DOWNLOAD LG WFS2018EKD Service Manual ↓ Size: 5.41 MB | Pages: 56 in PDF or view online for FREE

• Use to set a delayed finishing time.
• The time increases when the button

is pushed.

• The following settings are indicated

as the button is pushed 3    4    5

... 11    12    14    16    ...46    48

3 HOUR.

• To cancel delay time, turn the power

switch off.

(refer to page 24)

• Use for selecting wash program.
• This button allows you to  select 12

different  programs for  different kinds  of

laundry and dirtiness.

• program selections light up in sequence as

COTTON/NORMAL     STAIN CARE

SANITARY     SMART CLEANING

ECO COTTON     QUICK WASH 

BULKY/BEDDING     SPORTS WEAR

TOWELS     WOOL     TUB CLEAN

FAVORITE Select the desired program

by pressing the button.

• Use to start or pause the

washing process.

• Repeats start and pause by

pushing the button.

• It only operates in FUZZY Program..
• During being detected by the sensor,,the LED flashes green,orange

and red in turn.And,after detecting,the LED lights a specific color according to the detecting condition as

follows:

If the current washing condition (Detergent quantity,Water Temperature,water quality,etc.)is determined as

better than the standard one,it optimizes the algorithm to save the energy by decreasing washing       

time/strength,

and the LED automatically turns to red.

If the current washing condition is determined as worse than the standard one,it optimizes the algorithm by

increasing washing time/strength,and the LED automatically turns to orange.

If the current washing condition is determined as equal to the standard one,the algorithm has no change and the

LED turns to green.

• It marks the place to put the

phone to receive signal when a
problem occurs.

• Use to turn the power on or off.
• Push again and power goes on or off
• The power goes off automatically

*Because the detecting ability of the sensor may be decreased by using it for a long time,periodically use

TUB CLEAN course to clean the tub.(refer to page 21)

*Even if the water level is changed by the user in FUZZY(Normal)Program,

the sensor will still work.The sensor algorithm may differ according to models.

*The control panel may differ according to different models.

Used for normal loads, this mode
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly.

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL.
Or follow the
Detergent
manufacturer’s
instructions

• Use neutral Detergent

appropriate for the
laundry.

• When washing woolens

use a mild Detergent
recommended for
washing wool.

• Select the

WOOL
program on
the Control
panel.

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL
Or follow the
Detergent 
manufacturer’s
instructions

• Select the

QUICK
WASH
program on
the Control
panel.

• Select the

BULKY/BEDDING
program on the
Control panel.

• Select the 

SMART
CLEANING
program on the
Control panel.

• Spread

the jean
evenly in
the tub

Use this program for washing delicate
fabrics such as lingerie and woolens.
(wash only “water washable” clothes)
Before washing your woolens check
the care label for the washing
instructions.
(wash only water washable clothes)

Use this mode when washing
lightly soiled clothes for a short
time. The highly recommended
laundry amount is under 2.0kg.

Use BULKY/BEDDING program
when washing BULKY/BEDDING
of different sizes

Use this program to increaserinsing
performance.
This would include underwear and
baby clothes.
If someone has sensitive skin or
skin trouble,use this program.

• The pulsator rotates for

8 seconds to detect the

laundry load.

• Then the WATER

LEVEL and the amount

of Detergent to be

used will be shown and

water will be supplied.

• Water will be

supplied for 2

minutes after the

start of the wash to

supplement the

water the laundry

has absorbed.

• When the wash

program ends, the

buzzer will ring for

10 seconds before

the Power goes

off automatically.

• If water is already in the tub, or

putting wet laundry into the tub

before starting will increase the

WATER LEVEL. 

• With lightweight bulky loads,

WATER LEVEL can be set low. 

• Changes to Water Temperature

(HOT/COLD) and wash level are

possible during operation.

(refer to page 14) 

• When setting the WATER LEVEL manually,

do not set to Medium to prevent damage to

laundry.

• Washing with HOT water may damage the

laundry (Water is set to cold automatically).

Ensure that the load is under 2kg.

• In order to avoid  damage to laundry, the spin

cycle may appear slow. This also avoids

wrinkles and clothing may still contain some

water. This is normal.

• When static pressure of water is

more than 2kg/cm2, the QUICK

WASH course will be within

19min.

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL.
Or follow the
Detergent
manufacturer’s
instructions

• Select the

STAIN CARE
program on the
Control panel.

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL
Or follow the
Detergent 
manufacturer’s
instructions

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL
Or follow the
Detergent
manufacturer’s
instructions

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL
Or follow the
Detergent
manufacturer’s
instructions

• Select the

SANITARY
program on the
Control panel.

• Select the 

SPORTS WEAR 
program on the
Control panel.

• Select the 

TOWELS
program on the
Control panel.