DOWNLOAD LG WF-F63PC Service Manual ↓ Size: 1.79 MB | Pages: 62 in PDF or view online for FREE

Be sure to unplug the power to repair and replace

electric parts.

Remove two screw caps using a sharp tool and two

front panel fixing screws.

Push the front panel to the left side then pull it out

Disconnect the leads from the controller

Remove 4 screw from the front panel

Remove the PCB Assembly.

Fuse is located in the PCB assembly

For fuse replacement use the following rated fuse

* Rating of fuse

- 250V 6A fusing type for 220-240V product

- 125V 12A fusing type for 100-127V product

Be sure to make earth connection for trouble
diagnosis and parts replacement. If impossible,
touch earth wire on the body to remove electric
deviation between the body and product before
work.

leads

PCB Assembly

Fuse

Remove two back panel fixing screws in the back

side.

Disassemble the back panel.

Disconnect two connectors and disassemble the

power cord.

Remove a valve fixing screw & disconnect the

leads form the inlet valve.

Remove the inlet valve.

Disconnect the leads & the pressure tube from the

BP sensor.

Remove the BP sensor.

Remove Q-spring & two hinge pins then

disassemble the lid assembly

Remove two top cover fixing screws in the rear

then disassemble the top cover.

Remove tub cover fixing screws then disassemble

the tub cover.

Remove the pulsator fixing screw then disassemble

the pulsator.

Remove the hub fixing nut by a special tool.

Disassemble the inner tub.

Inlet valve

Power cord

BP sensor

Q-spring

Hinge Pin

Hinge Pin

Remove back cover fixing screws then disassemble
the back cover.

Disconnect the leads and the drain hose-p from the
drain pump.

Remove the pump fixing screws then disassemble
the drain pump.

Fall down the washer for clutch & motor removal.

Remove the belt.

Disassemble the clutch.

Remove two motor fixing screws then disassemble
the motor.

Separate top cover from washing machine.

As in the fig, lift snubber bar and take it out of out 

case with out tub.

Damper assembly shall not be disassembled.
Replace damper as assembly.

For assembly, keep the following.(Location & color)

Location

P/No.

PIVOT(Color)

,

A051

NATURAL

,

A052

BLUE

A

D

C

B

Pump fixing screw

Leads

Drain hose-p

Pulsator

Tub cover

Inner tub

Hub fixing nut

EX-LARGE

LARGE

MEDIUM

SMALL

8

4

2

1

8

4

2

1

8

4

2

1

FUZZY

ECONOMY

JEAN

WOOL

TURBO(SOAK) , Speedy soak

WASH

RINSE

SPIN

8

4

2

1

EX-LARGE

LARGE

MEDIUM

SMALL

8

4

2

1

8

4

2

1

FUZZY

ECONOMY

JEAN

WOOL

TURBO(SOAK), Speedy soak

WASH

RINSE

SPIN

• To use the CHECK PROGRAM (QC TEST MODE), press PROCESS key, and PROGRAM key at the

same time and then the POWER switch on without depositing any laundry.

NO

CHECK METHOD

LED INDICATOR

CHECK ITEM

1

2

3

4

5

6

7

8

Initial state

Press once

Press twice

Press 3 times

Press 4 times

Press 5 times

Press 6 times

Press 7 times

• After laundry amount detecting,

LED indicates laundry amount
and WATER LEVEL.

• Pump model: MEDIUM water

level Led ON.

• Non-pump model:water level

MEDIUM water level Led OFF.

• All LED on.

• After 2~3 seconds water level

frequency is displayed on LED.

• Laundry amount test.

• After checking laundry amount, motor

is on. (Left & Right)

• Cold water

• Hot water.

• Drain motor is 1st state is play.
• If lid is opened door error display.

(wash and spin LED blinks)

• Drain motor is 2nd state.(Only WF-T Series)

• Drain pump is on.

• AUTO off switch.

• WATER LEVEL FREQUENCY & LAUNDRY AMOUNT ARE DISPLAY BY THE LED (WATER LEVEL,

PROCESS, PROGRAM)

Ex) Water level check ; Frequency : 26.7 KHz

Ex) Laundry amount ; Water level : MEDIUM

Pulse : 25