LG WF-C9211T Service Manual ▷ View online
32
4-3. PROGRAM TIME CHART
2)
WFT(R,N,S,C,F)70A34(~5)D(E)P(H,C,D,E,F)
Contents of changed algorithm by the sensor
LED Display
Orange
Green
Red
W
ash Condition
Change Factor
W
ash time
W
ash time
W
ash pattern (Off time)
Spin time Rinse w
. level
Rinse times
Change Level
Max +8 min.
Max -4 min. Max +0.2 sec. Max +2 min. Max -0.2kHz Deep rinse addition
WF-C7611T / WF-C8015T
Algorithm change : The algorithm is automatically changed to operate at the optimum
Low Temperature High Hardness Little Detergent
Moderate Condition
High Temperature
Low Hardness
Much Detergent
Air Dry
Extra Rinse
Gentle Spin
Use this program to reduce remaining moiture inside off washing mashine and on the laundry
2nd deep rinse will be added. (Except for Speedy & Wool)
High speed spin is not operated.
33
4-4. ADJUSTMENT
1) Brake lever adjustment
• Shown as in the figure, untighten the adjustment
screw to keep clearance less than 1.9°æ0.1mm
between the tip and the brake lever.
And turn on the lock nut then paint it red.
between the tip and the brake lever.
And turn on the lock nut then paint it red.
• Painting part is adjusted in factory, it does not
need adjusting.
• Adjust the screw properly if the brake doesn't
work during spin.
CAUTION
2) Keeping clearance
• Keep the clearance about 2.0~3.5mm between
brake lever and P.V link as shown in the figure.
• Clutch pulley must be turning to one side P.V
Link is pulling the brake Lever.
• Clutch pulley must be turning to the left and the
right when P.V Linke does not pull the brake
Lever.
Lever.
CAUTION
3) V-belt adjustment
• Adjust the motor pulley by pushing the motor like
arrow , to make V-belt tension parallel when
pushed at the point of arrow .
pushed at the point of arrow .
• When the V-belt is not properly adjusted, the
motor will not be running or the belt will be
slipping.
slipping.
CAUTION
34
4-5. DISASSEMBLY INSTRUCTION
▶ Be sure to unplug the power to repair and
replace electric parts.
Be sure to make earth connection for
trouble diagnosis and parts replacement.
If impossible, touch earth wire on the body
to remove electric deviation between the
body and product before work.
trouble diagnosis and parts replacement.
If impossible, touch earth wire on the body
to remove electric deviation between the
body and product before work.
CAUTION FOR ELECTROSTATICS
1) Disassembly of Front Panel
& PCB Assembly
Remove two screw caps using a sharp tool
and two front panel fixing screws.
and two front panel fixing screws.
Push the front panel to the left side then
pull it out.
pull it out.
Disconnect the leads from the controller.
Remove 4 screw from the front panel.
Remove the PCB Assembly.
▶ Fuse is located in the PCB assembly For fuse
replacement use the following rated fuse
* Rating of fuse
* Rating of fuse
- 250V 6A fusing type for 220-240V product
- 125V 12A fusing type for 100-127V product
- 125V 12A fusing type for 100-127V product
leads
PCB Assembly
Fuse
35
2) Disassembly of Back Panel, Power
Cord, Inlet Valve & BP Sensor
Remove two back panel fixing screws in the
back side.
back side.
Disassemble the back panel.
Disconnect two connectors and disassemble
the power cord.
the power cord.
Remove a valve fixing screw & disconnect the
leads form the inlet valve.
leads form the inlet valve.
Remove the inlet valve.
Disconnect the leads & the pressure tube from
the BP sensor.
the BP sensor.
Remove the BP sensor.
3) Disassembly of Lid Assembly,
Top Cover, Tub Cover, Pulsator
& Inner Tub
& Inner Tub
Remove Q-spring & two hinge pins then
disassemble the lid assembly
disassemble the lid assembly
Remove two top cover fixing screws in the
rear then disassemble the top cover.
rear then disassemble the top cover.
Remove tub cover fixing screws then
disassemble the tub cover.
disassemble the tub cover.
Remove the pulsator fixing screw then
disassemble the pulsator.
disassemble the pulsator.
Remove the hub fixing nut by a special tool.
Disassemble the inner tub.
Inlet valve
Power cord
BP sensor
Q-spring
Hinge Pin
Hinge Pin
Click on the first or last page to see other WF-C9211T service manuals if exist.