LG WD14060D6 Service Manual ▷ View online
53
2 Push out PANEL ASSEMBLY, CONTROL after
Push the hook( , ) below.
2
1
1 The plate assembly(Top) is disassembled.
2 Pull out the drawer and unscrew 2 screws.
1 Unscrew two screws.
3 Unscrew the screws from the lower cover.
2 Disassembly lower cover assembly.
3 Unscrew the screw from the CABINET COVER.
1
2
3 Lift the side the Control Panel Assembly and
pull it out
CABINET COVER
Two screws are unscrewed
Pull the drawer to arrow direction.
Screws
Disassembly 3 connectors.
54
• Just check cut-off.
• Check the operating time.
* Door Locking time :
1~8
sec.
Check the time between from
input the power to parts
move up, then Door locked.
input the power to parts
move up, then Door locked.
* Door Releasing time :
25~100
sec.
Check the time between from off
the power to parts
move down, then Door released.
the power to parts
move down, then Door released.
1
1
1
1
2
4 Lift and separate the cabinet cover.
1 Unscrew two screws and cabinet cover
disassembled.
2 The Door Lock S/W is disconnected from the
wiring connector and the strap.
NOTE: When assembling the CABINET
COVER, connect the Door S/W connector.
COVER, connect the Door S/W connector.
SWITCH ASSY, DOOR LOCK
55
• V ~ U (8~11Ω)
• U ~ W (8~11Ω)
• W ~ V (8~11Ω)
• U ~ W (8~11Ω)
• W ~ V (8~11Ω)
Motor Stator
U V W
Hall Sensor
Ha
Hb
Common
• Common ~ Ha (5~15kΩ)
• Common ~ Hb (5~15kΩ)
• Common ~ Hb (5~15kΩ)
1 Remove the housing coupled the AG
(Connector, Hoses, Earth Screw)
2 Take out the screw of the AG.
1 Remove the back cover.
2 After loosening the bolt, Rotor, pull out the
rotor.
1 Remove the 6 bolts from the stator.
2 Disconnect the 2 connectors.
2 Disconnect the 2 connectors.
1 Remove the hinges (Damper) at the Tub.
3 The hinge at the base is pulled off.
(In directions of the arrow)
2 The Hinge(Damper) at the base is pulled off by
pressing on the snaps at the sharp end.
AG (Alpha Generator) (Option)
ROTOR ASSEMBLY, STATOR ASSEMBLY, FRICTION DAMPER
< Heater for STEAM>
• Rating : 230V 1100W
• Resistant : 42.5~49.5Ω
• Rating : 230V 1100W
• Resistant : 42.5~49.5Ω
56
1 Lower cover is disassembled.
2 Take out PWB assembly in front of washer.
3 Remove 3 clamps from the each hose.
4 Remove 4 screws from the base cabinet.
5 Disconnect the wire of pump.
6 Take out drain pump assembly in direction
of red arrow.
1 Loosen the nut.
2 Remove washing heater by pulling out.
2 Remove washing heater by pulling out.
When assembling the washing heater, insert
the heater to heater clip on the bottom of tub
and check the position of wire color.
the heater to heater clip on the bottom of tub
and check the position of wire color.
PUMP
HEATER
< Heater for Washing>
• Rating : 230V 2000W
• Resistant : 24.5~28.5Ω
• Rating : 230V 2000W
• Resistant : 24.5~28.5Ω
CAUTION
Click on the first or last page to see other WD14060D6 service manuals if exist.