LG WD-D1217RD6 Service Manual ▷ View online
12
6. OPERATION
Power Button
• Use this button to turn the power
On/Off.
Cycle Selector Knob
• Rotate the Cycle selector knob to select the cycle designed for
different types of fabric and soil levels.
Start/Pause
• Use this button to Start/
Stop the washer.
Status Indicator
• It shows elapsed time of the cycle the washer
is operating.
13
W
WAASSH
H RRIIN
NSSEE SSPPIIN
N
D
DRRYY
WASH
, RINSE, SPIN button
• Select a water temperature based on the type of load you
are washing.
• To change the spin speed, press the Spin Speed button
repeatedly to cycle through available options.
TEMP. SELECTOR
•
Select a water temperature
based on the type of load you
are washing.
Option Button
•
LOW TEMP - For delicate fabrics
•
IRON - For damp drying fabrics
•
NORMAL - For general drying
•
MORE - For heavier fabrics
14
7. TROUBLESHOOTING
7-1. BEFORE PERFORMING SERVICE
Be careful of electric shock when disconnecting parts while troubleshooting.
The voltage of each terminal is 120 V AC and DC when the unit is plugged in.
7-2. QC TEST MODE.
The washer must be empty and the controls must be in the off state.
1. Press the SPIN SPEED and SOIL LEVEL buttons simultaneously.
2. Press the Power button, while the above condition. Then buzzer will sound twice.
3. Press the Start/Pause button repeatedly to cycle through the test modes.
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY
Press the Spin and Rinse button simultaneously.
So, for example a display indicating 241: a Water level frequency of 241 x.1 kHz
= 24.1 kHz
The digits indicate the water level frequency ( x.1 kHz ).
Number of times the
Start/Pause button is pressed
Check Point
Display Status
None
Turns on all lamps and locks the door.
1 time
Tumble clockwise.
rpm
2 times
Low speed Spin.
rpm + Water Level
3 times
High speed Spin.
rpm + Water Temperature
4 times
Inlet valve for prewash turns on.
Water level frequency (25~65)
5 times
Inlet valve for main wash turns on.
Water level frequency (25~65)
6 times
Inlet valve for hot water turns on.
Water level frequency (25~65)
7 times
Inlet valve for steam turns on.
Water level frequency (25~65)
8 times
Inlet valve for bleach turns on.
Water level frequency (25~65)
9 times
Tumble counterclockwise.
rpm (42~50)
10 times
Heater turns on for 3 sec.
Water temperature
11 times
Circulation pump turns on.
Water level frequency (25~65)
12 times
Drain pump turns on.
Water level frequency (25~65)
13 times
Off
-
15
7-4. ERROR DISPLAY
If you press the START/PAUSE button when an error is displayed, any error except
will
disappear and the machine will go into the pause status.
In case of
if the error is not resolved within 20 sec., or the in case of other errors,
if the error is not resolved within 4 min., power will be turned off automatically and the error code will
blink. But in the case of
blink. But in the case of
, power will not be turned off.
ERROR SYMPTOM
CAUSE
WATER INLET
ERROR
• Correct water level (246) is not reached within 8 minutes
after water is supplied or it does not reach the preset water
level within 25 minutes.
level within 25 minutes.
• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.
1
2
IMBALANCE
ERROR
• Not fully drained within 10 minutes.
3
DRAIN
ERROR
• Water is overflowing (water level frequency is over 213).
If is displayed, the drain pump will operate to
drain the water automatically.
drain the water automatically.
4
OVER FLOW
ERROR
• The SENSOR SWITCH ASSEMBLY is out of order.
5
PRESSURE
SENSOR
ERROR
• Door not all the way closed.
• Loose electrical connections at Door switch and
• Loose electrical connections at Door switch and
PWB Assembly.
• The DOOR SWITCH ASSEMBLY is out of order.
6
DOOR OPEN
ERROR
• The THERMISTOR is out order.
7
HEATING
ERROR
Click on the first or last page to see other WD-D1217RD6 service manuals if exist.