LG WD-90MFD Service Manual ▷ View online
Before servicing ask troubles of customers
Check the adjustment(power supply is 220-240V~, remove the transit bolts....)
Check the troubles referring to the trouble shooting.
Decide service steps referring to disassembly instructions.
And then, service and repair.
After servicing, operate the appliance whether it works O·K or NOT.
Check the adjustment(power supply is 220-240V~, remove the transit bolts....)
Check the troubles referring to the trouble shooting.
Decide service steps referring to disassembly instructions.
And then, service and repair.
After servicing, operate the appliance whether it works O·K or NOT.
■ STANDARD INSTALLATION
The appliance should be installed as follows.
REMOVE THE TRANSIT
INSTALL THE APPLIANCE
ADJUST THE
BOLTS
ON FLAT AND FIRM SURFACE
HORIZONTAL
• Remove the transit bolts
• Turn the leveling feet to
(4EA:①)with supplied spanner.
set the appliance horizontally.
• Keep the transit bolts and
spanner for future use.
• Insert the 4 caps
provided into the hole
• The appliance goes up by
rotating the feet clockwise.
• The appliance come down by
rotating the feet counter
clockwise.
4. INSTALLATION
7
1
Low
High
■ HOW TO CONNECT INLET HOSE
• Check that the rubber packing is inside of the
valve connector.
• Connect the inlet hose firmly to prevent leak.
■ CONNECT DRAIN HOSE
■ CONNECT POWER PLUG
8
· Make sure that the hose is not twisted.
※ The drain hose should be placed under 100cm from the floor.
· Connect the power plug to the wall outlet.
· Avoid connecting several electric devices,
It may be the cause of the fire.
· Avoid submerging the end of the hose.
TEST OPERATION
9
•Connect the power plug to
the outlet.
•In case of Coloreds program.
•Connect the inlet hose.
Preparation for
Press the POWER button.
Press the Start/Pause
washing.
button.
·Check if the drum rotates
·Check if water is supplied
clockwise and counterclockwise.
through the detergent
dispenser.
dispenser.
·Press the Time Delay and Rinse
Hold buttons simultaneously and
the present temperature will be
displayed.
the present temperature will be
displayed.
·Power off and then power on.
·Check if the door can be
·Check if the door can be
opened after 3 minutes.
·Turn off Wash and Rinse after
pressing the Start/Pause button
and start the machine again.
and start the machine again.
·Check drain and spin.
·If SVC is needed during
check, remove
the remaining water by pulling
out the hose cap.
Check the water heating.
Check automatic reverse
Check the water supply.
turn.
Check drain and spin
Power off and open the
Water removal
door
10
5. OPERATION
LED display
•Display the estimated remaining time
(Hour : Minute) to finish.
•In case of abnormal operation, error
indications are displayed.
( )
•See troubleshooting guide.
Water temperature selector
•Press the button to select water
temperature.
•95。C is selected for Cotton only.
•By pressing the button while
•By pressing the button while
operating the washer, the present
temperature is displayed.
temperature is displayed.
Wash program selector
•8 program can be set depending on the type of the laundry.
•If the power button is pressed, Cotton program is automatically
•If the power button is pressed, Cotton program is automatically
set.
•By turning the dial, [Cotton-Synthetic -Wool/Silk-Hand Wash -
Drain-Rinse+Spin-Quick 30-Delicate ]can be selected.
(The opposite is possible)
(The opposite is possible)
Start/Pause button
•Use the button to start or
pause wash cycle.
•The power turns off
automatically 4 minutes
after the pause button is
pressed.
after the pause button is
pressed.
• If the laundry is heavily
soiled “Intensive” option
is effective.
is effective.
• By selecting the
Intensive option, the
wash time may be
extended, depending on
the program selected.
wash time may be
extended, depending on
the program selected.
• Is selected by pressing the Rinse Hold
button this function leaves clothes in
the machine; suspended in the water
after a rinse without entering into spin.
the machine; suspended in the water
after a rinse without entering into spin.
• To proceed through to a drain or spin,
once the rinse hold function is
completed using to program dial scroll
to the required program. (Spin)
completed using to program dial scroll
to the required program. (Spin)
Intensive
Rinse Hold
, , , , , , , , ,
Click on the first or last page to see other WD-90MFD service manuals if exist.