LG WD-80160FU Service Manual ▷ View online
20
NO
YES
NO
YES
NO
YES
NO
NO
YES
YES
YES
NO
NO
NO
YES
Wiring diagram
option (HOT)
option (HOT)
MAX
max
Is the water supply shut-off?
Is the tap opened?
Is the inlet valve filter clogged with impurity?
Is resistance of the inlet valve connector
between the 2 to 8
between the 2 to 8
k
?
Check the voltage between each terminals of inlet
Valve is 220 - 240V~.
(Refer to 7-2 TEST MODE)
Is water supplied?
Are replaceptacles correctly connected to the
terminals of inlet valve?
terminals of inlet valve?
Is detergent put in the correct compartment of
the drawer?
the drawer?
Is the detergent caked or hardened?
Open the tap.
Clean the filter.
Replace the inlet valve.
Replace PWB assembly
Refer to solution
NO INLET
Check the wiring on the
dispenser.
Put the detergent in the
correct position
PRE+MAIN
MAIN WASH
: Detergent
Clean the drawer.
NO WATER SUPPLY
DETERGENT DOES NOT FLOW IN
MAIN
WASH
SOFTENER
PRE -
WASH
21
YES
YES
YES
NO
NO
NO
NO
NO
YES
YES
YES
YES
Wiring diagram
option (HOT)
MAX
max
ABNORMAL SOUND
SOFTENER DOES NOT FLOW IN
Fix the bolt tightly.
Replace the V-belt
(4400FR3116A)
(4400FR3116A)
Replace the motor.
Refer to
NO WATER SUPPLY
Check the wiring on the
dispenser.
dispenser.
Put it in the correct
compartment.
compartment.
Clean the cap and
drawer.
drawer.
Is the pulley bolt loosened?
Is the belt worn?
Is there friction noise from the motor?
Is water supplied?
Are receptacles correctly connected to the terminals
of inlet valve?
of inlet valve?
Is softener put in the correct compartment of
drawer?
Is the softener cap clogged?
22
YES
YES
NO
NO
NO
NO
YES
YES
NO
PWB ASSEMBLY
PWB ASSEMBLY
YES
NO
1
2
Replace the sensor
(pressure).
Replace the sensor
(pressure).
Repair drain hose
Remove foreign material.
Reconnect or repair the
connector
connector
Replace the pump
assembly
assembly
Replace the PWB
When pressing [Option] and [Spin] at the same time
after draining, is the water level frequency 252 or
more?
When pressing [Option], [Spin] buttons at the
same time while wash, is the water level
frequency between 220 - 240?
after draining, is the water level frequency 252 or
more?
When pressing [Option], [Spin] buttons at the
same time while wash, is the water level
frequency between 220 - 240?
Replace the PWB assembly.
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Is the connector disconnected, disassembled?
Is the coil of drain pump cut-off?
(resistance of coil is 90~160 )
When checking voltage between connectors
( , )on spinning, is the voltage 220 - 240V~
as the figure?
HEATING WITHOUT WATER
DRAIN MALFUNCTIONING
23
NO
YES
YES
WASH HEATER TROUBLE
4
1
AC 220-240V
NO
NO
YES
NO
YES
(1)
Replace the thermistor
Push the thermistor
tightly to the rubber.
When disconnect the connector (1) on the
PWB assembly is the resistance of the
Natural connectors
PWB assembly is the resistance of the
Natural connectors
( White),
(Blue / White) between 2.5k
to 180k
(105
~0
)?
When checking thermistor on the tub,
is the thermistor loosened above 2mm from
the rubber?
When checking the voltage between two
receptacles of the PWB assembly during
washing.
Is the voltage AC 220-240V?
receptacles of the PWB assembly during
washing.
Is the voltage AC 220-240V?
After power off, is the resistance between yellow
wire and red wire of
connector 10 to 30 ?
wire and red wire of
connector 10 to 30 ?
After power off, is the resistance of heater
10 to 30 ?
Replace the PWB
assembly.
assembly.
Normal.
Replace the heater
assembly.
assembly.
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
Click on the first or last page to see other WD-80160FU service manuals if exist.