LG WD-80154S Service Manual ▷ View online
28
① Remove the back cover.
② Take off the belt turning the pulley.
③ Unscrew the bolt to pull out the pulley.
② Take off the belt turning the pulley.
③ Unscrew the bolt to pull out the pulley.
① Unscrew 2 screws from the bracket.
② Push the motor in the arrow direction for
② Push the motor in the arrow direction for
disassembling.
③ When reassembling the motor, make sure that motor
mounting bushings are not taken off from the bracket.
① Pull out the hinge, pressing its snap.
② Do not use the pulled out hinge again. It may be taken
② Do not use the pulled out hinge again. It may be taken
off during operation.
PULLEY, MOTOR, DAMPER
(PULLEY)
(MOTOR)
(DAMPER)
Open the lower cover cap (①) by
using a coin. Turn the drain plug
(②) to pull out the hose.
using a coin. Turn the drain plug
(②) to pull out the hose.
Unplug the drain plug (②), then
the water flows out,
At this time use a vessel
to prevent water flowing on the
floor. If the water does not flow any
more,turn the pump filter (③) open
to the left.
the water flows out,
At this time use a vessel
to prevent water flowing on the
floor. If the water does not flow any
more,turn the pump filter (③) open
to the left.
Take out any foreign material
from the pump filter (③). After
cleaning, turn the pump filter(③)
clockwise and insert the
drain plug (②)to the original
place. close the lower cover cap.
from the pump filter (③). After
cleaning, turn the pump filter(③)
clockwise and insert the
drain plug (②)to the original
place. close the lower cover cap.
Clean the drain pump filter
1
100
2
3
2
3
Pump Outlet Hose
Tub Pump
Bellows
Bellows
29
① Remove pump outlet hose.
② Remove tub pump bellows.
③ Remove cap (Remaining Hose.)
④ Disconnect the wiring.
⑤ Unscrew 2 screws.
⑥ Remove the pump.
② Remove tub pump bellows.
③ Remove cap (Remaining Hose.)
④ Disconnect the wiring.
⑤ Unscrew 2 screws.
⑥ Remove the pump.
① Loosen the M6 heater nut to pull out the heater.
When mounting the heater, be sure to insert the heater
into the heater clip on the bottom of the tub.
① Pull it out by holding the thermistor bracket.
If it is pulled by the wire, it may be broken.
② When mounting the thermistor again, make sure that it
is got back tight to the bushing.
PUMP
HEATER
THERMISTOR
CAUTION
30
SWITCH ASSEMBLY, DOOR LOCK
WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB
① Take apart the cabinet cover clamp and release
the gasket.
② Unscrew 2 screws holding the door lock.
③ Disconnect the door lock from the wiring connector.
③ Disconnect the door lock from the wiring connector.
① Remove the heater.
② Remove the foreign material (wire, coin and others) by
② Remove the foreign material (wire, coin and others) by
inserting a long bar through the hole.
10-1.THE EXPLODED VIEW OF CABINET ASSEMBL
Y
31
10. EXPLODED VIEW
A485
A110
A101
A141
A131
A130
A133
A303
A276
A310
A300
A220
A440
A410
A103
A430
A104
A102
A100
A153
A150
A151
A140
A152
A154
A134
Click on the first or last page to see other WD-80154S service manuals if exist.