LG WD-12479RD Service Manual ▷ View online
20
8-2.FAULT DIAGNOSIS AND TROUBLE SHOOTING
1. Be careful of electric shock or disconnecting the parts while trouble shooting.
2. First of all, check the connection of each part terminal with wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, Put in the connectors correctly.
NO
NO
YES
YES
YES
NO
NO
YES
Check the fuse?
Replace MAIN PWB
ASSEMBLY
ASSEMBLY
Reconnect the PWB
ASSEMBLY
ASSEMBLY
Reconnect the PWB
ASSEMBLY
ASSEMBLY
When measuring the voltage of the outlet,
is the voltage AC 220-240V~?
Is the led(1) on?
Is connector(2) disconnected or
disassembled?
Is wire of the PWB ASSEMBLY disconnected?
Replace PWB ASSEMBLY
NO POWER
CAUTION
21
NO
YES
NO
NO
YES
NO
YES
YES
NO
NO
YES
YES
YES
NO
NO
NO
YES
5
4
Dry
Steam
Steam
Dry
Is water supply shut-off?
Is the tap opened?
When you press both Rinse button and Spin button
simultaneously, is the water level frequency below
240?
simultaneously, is the water level frequency below
240?
Is the inlet valve filter clogged with impurity?
Is resistance between each terminal of INLET
VALVE ASSEMBLY is 2~8
VALVE ASSEMBLY is 2~8
kΩ
?
Check the voltage of the inlet valve connector
AC 220-240V~.
(Refer to 7-2 QC TEST MODE)
Is water supplied?
Are replaceptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
terminals of the INLET VALVE ASSEMBLY?
Is detergent put in the correct compartment of
the drawer?
the drawer?
Is the detergent hardened?
Open the tap.
Check the AIR CHAMBER
and the tube clogged
with impurity.
and the tube clogged
with impurity.
Clean the filter.
Replace the INLET VALVE
ASSEMBLY.
Replace the MAIN PWB
ASSEMBLY
Refer to
「NO WATER SUPPLY」
Check the wiring on the
dispenser.
dispenser.
Put the detergent in the
correct position
PRE+MAIN
MAIN WASH
: Detergent
Clean the drawer.
NO WATER SUPPLY
DETERGENT DOES NOT FLOW IN
22
YES
YES
NO
NO
NO
NO
YES
YES
YES
YES
Steam
Dry
A B N O R M A L S O U N D
S O F T E N E R D O E S N O T F L O W I N
Fix the bolt tightly.
Replace the STATOR
ASSEMBLY or ROTOR
ASSEMBLY.
ASSEMBLY or ROTOR
ASSEMBLY.
Refer to
「NO WATER SUPPLY」
Check the wiring on the
dispenser.
dispenser.
Put it in the correct
compartment.
compartment.
Clean the cap and
drawer.
drawer.
Is the motor bolt loosened?
Is there friction noise from the motor?
Is water supplied?
Are receptacles correctly connected to the terminals
of the INLET VALVE ASSEMBLY?
of the INLET VALVE ASSEMBLY?
Is softener put in the correct compartment of the
drawer?
Is the softener cap clogged?
23
(1)
(2)
AC 220-240V
Replace the
S.PRESSURE SWITCH
ASSEMBLY
S.PRESSURE SWITCH
ASSEMBLY
Replace the MAIN PWB
ASSEMBLY
ASSEMBLY
Repair the DRAIN HOSE
ASSEMBLY.
ASSEMBLY.
Remove foreign material.
Reconnect or repair the
connector
connector
Repair the DRAIN PUMP
ASSEMBLY.
ASSEMBLY.
Repair the MAIN PWB
ASSEMBLY.
ASSEMBLY.
When pressing Rinse and Spin at the same time
after draining, is the water level frequency 255?
When pressing Rinse and Spin buttons at the
same time while washing, is the water level
frequency between 230 - 243 ?
after draining, is the water level frequency 255?
When pressing Rinse and Spin buttons at the
same time while washing, is the water level
frequency between 230 - 243 ?
After completely drained and turn
off water, the washing machine is
operated under the [Sanirary] condition.
Check the voatage between two pins is the
Voltage 0 V AC?
off water, the washing machine is
operated under the [Sanirary] condition.
Check the voatage between two pins is the
Voltage 0 V AC?
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Is the connector disconnected, disassembled?
Is the coil of the drain pump cut-off?
(resistance of coil is 80~150Ω)
(resistance of coil is 80~150Ω)
When checking voltage between connectors
(①, ②)on spinning, is the voltage 220-240V
as the figure?
HEATING WITHOUT WATER
D R A I N M A L F U N C T I O N I N G
Click on the first or last page to see other WD-12479RD service manuals if exist.