LG WD-1050FB Service Manual ▷ View online
■ HOW TO CONNECT INLET HOSE
Check that the rubber washer is inside of the
valve connector.
Connect the inlet hose firmly to prevent leak.
■ CONNECT DRAIN HOSE
■ CONNECT POWER PLUG
8
· Make sure that the hose is not twisted.
※ The drain hose should be placed under 100cm from the floor.
· Connect the power plug to the wall outlet.
· Avoid connecting several electric devices,
It may be the cause of a fire.
· Avoid submerging the end of the hose.
TEST OPERATION
9
Connect the power plug to
In case of Coloreds program.
the outlet.
Connect the inlet hose.
Preparation for
Press the power button.
Press the START/PAUSE
washing.
button.
·Press the button TEMP
·Check if the drum rotates
·Check if water is supplied
and the present temperature
clockwise and counter-
through the detergent
will be displayed.
clockwise.
dispenser.
·Power off and then power on.
·Check if the door can be
·Check if the door can be
opened after door lock lamp
turns off.
·Turn off Wash and Rinse after
pressing the Start/Pause button
and start the machine again.
and start the machine again.
·Check drain and Spin.
·If SVC is needed during check,
remove the remaining water by
pulling out the hose cap.
pulling out the hose cap.
Check the water heating.
Check automatic reverse
Check the water supply.
turn.
Check drain and spin
Power off and open the
Water removal
door
10
5. OPERATION
■ WD-1050(5)F(H)(B) / WD-1253(5)F(H)(B) / WD-1054(6)F(H)B / WD-1254(6)F(H)B
60
.
LED display
Display the remaining time (Hour : Minute ) to
finish.
In case of abnormal operation, error indications
are displayed.
finish.
In case of abnormal operation, error indications
are displayed.
( )
See troubleshooting guide.
Water temperature selector
Press the button to select water temperature.
The water temperature
The water temperature
[40
。C
60
。C
cold
(30
。C)] can be selected in
Coloreds, or Synthetic.
95
。C is selected for Whites hHeatingionly.
By pressing the button while operating the washer,
the present temperature is displayed.
the present temperature is displayed.
For manual wash, rinse, and spin speed
Use these buttons to change wash/ rinse/spin.
When lamp is off, no selection has been made.
Prewash is available for Coloreds, Whites,
and Synthetic.
When lamp is off, no selection has been made.
Prewash is available for Coloreds, Whites,
and Synthetic.
hColoreds, Heating, and Synthetici
Door lock lamp
It shows whether the
door can be opened or
not.
when the lamp is on,
door can be opened or
not.
when the lamp is on,
the door can’t be
opened.
Error display.
The display blinks if there is
an error.
an error.
no inlet : Trouble with
water supply.
imbalance : The laundry is
tilted to one
side.
side.
no drain : If the drain pump
filter is clogged.
Rinse hold
If you desire to leave fabrics in the machine
without spinning after rinse to prevent wrinkling,
you may select rinse Hold by pressing the
Rinse button.
To drain and spin, press the Rinse button to
turn off the rinse hold lamp.
without spinning after rinse to prevent wrinkling,
you may select rinse Hold by pressing the
Rinse button.
To drain and spin, press the Rinse button to
turn off the rinse hold lamp.
,
,
,
,
,
,
Refer
Refer
14
11
: for Australia
Wash program selector
5 programs can be set depending on the type of the
laundry.
If the power button is pressed.
Coloreds program is automatically set.
By pressing the button, [ Coloreds
laundry.
If the power button is pressed.
Coloreds program is automatically set.
By pressing the button, [ Coloreds
Whites
Synthetic
Delicate
Wool ] can be selected.
hColoreds Favourite Heating Synthetic Wooli
Start/Pause button
Use the button to start or
pause wash cycle.
The power turns off
automatically 4 minutes
after the pause button is
pressed.
pause wash cycle.
The power turns off
automatically 4 minutes
after the pause button is
pressed.
Time Delay
Press the button when delayed washing is
needed.
needed.
When the button is pressed, [
3:00
] is displayed,
A maximum delay of [19:00] hours can be set.
Each press advances time delay by the hour.
Use [Power] button to cancel [Time Delay].
Use [Power] button to cancel [Time Delay].
Eco/Rapid
If you press the Eco/Rapid button in White
hHeatingi
program, Eco function is selected. Eco function gives
you almost the same washing effect as that in 95
you almost the same washing effect as that in 95
。C
with less energy consumption.
If you press the Eco/Rapid button in Coloreds or
Synthetic program, Rapid function is selected.
Rapid function reduces the whole time including the
washing and rinsing time about by half an hour.
If you press the Eco/Rapid button in Coloreds or
Synthetic program, Rapid function is selected.
Rapid function reduces the whole time including the
washing and rinsing time about by half an hour.
Child - lock
Child Lock system can be
set and canceled by pressing
both [Temp] and [Eco/Rapid ]
button simultaneously.
set and canceled by pressing
both [Temp] and [Eco/Rapid ]
button simultaneously.
Once Child Lock is set,
all button are inoperable.
all button are inoperable.
Child Lock system can be
set anytime even during
Power-off, on pause and
operation.
set anytime even during
Power-off, on pause and
operation.
It is automatically cancelled
when an operational error
occur, and when the cycles
ends.
when an operational error
occur, and when the cycles
ends.
Power button
Press the button to
turn power on and
off.
turn power on and
off.
Click on the first or last page to see other WD-1050FB service manuals if exist.