LG WD-1050FB Service Manual ▷ View online
36
①
① Disassemble the top plate assembly.
②
②
② Pull out the drawer slightly upward.
③
③
③ Unscrew 2 screws.
①
① Disassemble hose clamps and hoses.
②
②
② Disassemble ventilation bellows and water inlet
bellows from tub.
①
① Disassemble the top plate assembly.
②
②
② Unscrew 2 screws.
③
③
③ Disconnect connector from the wiring.
DISPENSER ASSEMBLY
PWB ASSEMBLY (POWER)
DISPENSOR ASSEMBLY
Option (HOT)
DRAWER
WD-6550F/WD-8050F(H)
37
① Disconnect the wiring connector.
② Unscrew 2 screws from the back.
② Unscrew 2 screws from the back.
When reconnecting the connector
~WD-1253FH(B)/1255FH(B)/1254(6)FHB/
WD-1054(6)FHB/ 1050FH(B)/1055FH(B)/8050(4)FH(B)
₩
① Remove the back cover.
② Unscrew 2 screws.
③ Pull the PWB assembly (Main) as shown.
② Unscrew 2 screws.
③ Pull the PWB assembly (Main) as shown.
① The Top cover is removed.
② Unscrew 2 screws.
③ Pull the PWB assembly (Main) as shown.
② Unscrew 2 screws.
③ Pull the PWB assembly (Main) as shown.
1
2
3
INLET VALVE
PWB ASSEMBLY (MAIN)
VALVE#1 (MAIN)
White/Black - Black
VALVE#2 (PRE)
Gray/ White - Black
VALVE#3 (HOT)
Blue/Red-Black
■ WD-6550FB / WD-8050(4)F(H)B / WD-1050(5)F(H)B / WD-1253(5)F(H)(B) / WD-1054(6)F(H)B / WD-1254(6)F(H)B
■ WD-6550F / WD-8050F(H) / WD-1050(5)F(H)
38
①
① Open the door completely.
②
②
② Remove the two screws from the hinge.
①
① Take apart the cabinet gasket clamp.
②
②
② Unscrew 2 screws from the cabinet cover.
③
③
③ Open the lower cover cap and unscrew 1 screw inside.
④
④
④ Take apart the lower cover.
①
① Unscrew all the screws on the upper and lower sides of
the cabinet cover.
①
① Take apart the tub gasket clamp.
②
②
② Make sure that the drain hole of the gasket is put
beneath when reassembling the gasket.
※Refer to the arrow mark on the tub cover.
GASKET ASSEMBLY
DOOR
39
①
① Remove the back cover.
②
②
② Take off the belt turning the pulley.
③
③
③ Unscrew the bolt to pull out the pulley.
①
① Unscrew 2 screws from the bracket.
②
②
② Push the motor in the arrow direction for
disassembling.
③
③ When reassembling the motor, make sure that motor
mounting bushings are not taken off from the bracket.
①
① Pull out the hinge, pressing its snap.
②
②
② Do not use the pulled out hinge again. It may be taken
off during operation.
1
2
3
Hinge,
Damper
Damper
Damper
PULLEY, MOTOR, DAMPER
(PULLEY)
(MOTOR)
(DAMPER)
Open the lower cover cap (
)
by using coin.Turn the drain plug
(
(
) to pull out the hose.
Unplug the drain plug (
) , then
the water flows out.
At this time use a vessel
to prevent water flowing on the
floor. If the water does not flow any
more,turn the pump filter (
At this time use a vessel
to prevent water flowing on the
floor. If the water does not flow any
more,turn the pump filter (
)
open to the left.
Take out any foreign material
from the pump filter (
from the pump filter (
).
After cleaning, turn the pump
filter (
filter (
) clockwise and insert
the
drain plug (
) to the
original place. close the lower
cover cap.
cover cap.
Clean the drain pump filter
1
100
3
2
3
2
■ WD-6550F(B) / WD-8050F(H)(B) / WD-1050(5)F(H)(B) / WD-1253(5)F(H)(B)
Click on the first or last page to see other WD-1050FB service manuals if exist.