LG WD-10121TD Service Manual ▷ View online
21
AC 220-240V
NO
NO
YES
YES
YES
NO
NO
NO
NO
YES
YES
NO
PWB ASSEMBLY (MAIN)
PWB ASSEMBLY (MAIN)
Replace the sensor
(pressure)
(pressure)
Replace the PWB
assembly
assembly
Repair drain hose
Remove foreign
material.
material.
Reconnect or repair the
connector
connector
Replace the pump
assembly
assembly
Replace the PWB
assembly (Main)
assembly (Main)
When pressing [Rinse] button and [Spin]
button at the same time after draining,
is the water level frequency 252 or more?
When pressing [Rinse] button and [Spin]
button at the same time while wash,
is the water level frequency between 230~245?
button at the same time after draining,
is the water level frequency 252 or more?
When pressing [Rinse] button and [Spin]
button at the same time while wash,
is the water level frequency between 230~245?
Checking voltage between two pins
as press the power button is the voltage
220 - 240V~ ?
as press the power button is the voltage
220 - 240V~ ?
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Is the connector disconnected,
disassembled?
disassembled?
Is the coil of drain pump cut-off?
(resistance of coil is 90~160
(resistance of coil is 90~160
)
When checking voltage between connectors
(
(
, ) on spinning, is the voltage
220 - 240V~ as the figure?
HEATING WITHOUT WATER
DRAIN MALFUNCTIONING
Rinse
Spin
22
NO
YES
YES
WASH HEATER TROUBLE
When checking the voltage between
connector the PWB assembly (Main)
during whites washing ,Is the voltage
220 - 240V ?
connector the PWB assembly (Main)
during whites washing ,Is the voltage
220 - 240V ?
Replace the PWB
assembly (Main)
assembly (Main)
YES
NO
After power off and the heater terminal is
disconnected, is the resistance 10 to 30 ?
disconnected, is the resistance 10 to 30 ?
Replace the heater
assembly
assembly
NO
After power off,is the resistance of wire
(RED-YELLOW) connectors between
10 to 30 ?
(RED-YELLOW) connectors between
10 to 30 ?
Normal
NO
YES
RED
YELLOW
1
2
3
~
220 - 240V~
PWB ASSEMBLY (MAIN)
Replace the thermistor
(6322FR2046C)
(6322FR2046C)
Push the thermistor
tightly to the rubber.
When checking thermistor on the tub,
is the thermistor loosened above 2mm from
the rubber?
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
23
Wash
Spin
NO
YES
YES
YES
NO
NO
YES
NO
NO
YES
SPIN TROUBLE
Check the sensor
(Pressure) or hose
(Sensor).
If the problem is on the
sensor or the hose, replace
the sensor or the hose.
(Pressure) or hose
(Sensor).
If the problem is on the
sensor or the hose, replace
the sensor or the hose.
Normal
Correct the connector.
Correct the connector.
Replace the STATOR
ASSEMBLY
(4417EA1002D)
ASSEMBLY
(4417EA1002D)
While spinning, is the frequency of the
water level 248 or more? The frequency can be
checked by pressing the Rinse button
and Spin button at the same time
on the program.
water level 248 or more? The frequency can be
checked by pressing the Rinse button
and Spin button at the same time
on the program.
When pressing Wash button and Spin button
and POWER button at the same time after
power off, press the START/PAUSE button 2 times,
is the drum low speed spin?
and POWER button at the same time after
power off, press the START/PAUSE button 2 times,
is the drum low speed spin?
Is it disconnected, or disassembled?
[White : 3pin ( ), Red:3pin ( ),
Red:3pin ( ), National:4pin ( )]
[White : 3pin ( ), Red:3pin ( ),
Red:3pin ( ), National:4pin ( )]
Is it disconnected, or disassembled?
White : 3pin( ), White:4pin( )]
White : 3pin( ), White:4pin( )]
Check the motor connector, Is the resistance of
the terminal same as the figure?
MOTOR TERMINAL (1)
Resistance of terminal:
Replace the PWB assembly.
(2)
(1)
~
~
~
/
/
Rinse
Spin
Power
24
Be sure to unplug the machine out of the outlet before disassembling and repairing the parts.
9. DISASSEMBLY INSTRUCTIONS
Unscrew 2 screws on the back of the top plate.
Pull the top plate backward and upward as shown.
Disconnect the PWB Assembly connector from Main
lead wire Assembly.
Pull out the drawer and unscrew 2 screws.
Push upper hooks down on the top and pull the control
panel.
Disconnect the PWB assembly (Main & Display) from
the control panel by unscrewing 3 screws.
CONTROL PANEL
PLATE ASSEMBLY (TOP)
PWB ASSEMBLY
(DISPLAY)
(DISPLAY)
HOOK
PANEL ASSEMBLY (CONTROL)
Click on the first or last page to see other WD-10121TD service manuals if exist.