LG T1209DB / T1209DS / T1409DB / T1409DS Service Manual ▷ View online
36
Water Guide
Fixing Bolt
Hall Sensor
Stator Housing
6) Replacement of Rotor & Stator
Disassemble rotor nut with boxer(M18) or spaner.
(
(
In assembled, the force is over than 200kgf.cm)
Disassemble rotor, pull out the rotor as shown the
figure.
figure.
Disconnect fixing screw and disassemble the water
guide.
guide.
Before disassemble stator,disconnect the hall sensor
and stator housing.
and stator housing.
37
7) Replacement of Bearing housing asm
SNAP RING.
Hall Sensor
Stator Housing
Water Guide
Loosen the 6 fixing screws on the stator.
(Lower
(Lower
upper position screws)
Check the direction of SNAP RING.
(The handle of snap ring is toward to rotor and stator.)
(The handle of snap ring is toward to rotor and stator.)
Preventing fallen the stator, tighten with one hand and
then loosen the last screw.
then loosen the last screw.
For assembly take care lead wire's state, it produce a
noise and cut attach the rotor.
noise and cut attach the rotor.
Loosen 14 Fixing screws on the Bearing Housing ASM
and pull up it.
and pull up it.
38
4-6. TROUBLE SHOOTING AGAINST COMMON WASHING PROBLEMS
Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage. For
satisfactory washing results, follow these instructions.
satisfactory washing results, follow these instructions.
WASH PROBLEM
Problems
Poor soil
removal
removal
• Not enough Detergent
• Wash Water
• Wash Water
Temperature too low.
• Overloading the washer
• Incorrect wash cycle
• Incorrect sorting
• Stain not pre treated.
• Incorrect wash cycle
• Incorrect sorting
• Stain not pre treated.
Possible Causes
Solutions & Preventive Measures
• Use correct amount of Detergent for load size, amount of soil and
water Hardness.
• Use WARM or HOT water for normal soil.
Different Water Temperature may be required according to soil
type. (refer to page 10)
type. (refer to page 10)
• Reduce load size.
• Wash with JEAN or SOAK & JEAN wash cycle for heavy soiled
• Wash with JEAN or SOAK & JEAN wash cycle for heavy soiled
laundry.
• Separate heavily soiled items from lightly soiled ones.
• Pretreat stain and heavy soil according to directions shown on
• Pretreat stain and heavy soil according to directions shown on
page 9.
Blue, Grey, or
Brown Stains
Brown Stains
• Undiluted fabric softener
dispensed directly onto
fabric
fabric
• Rub the stain with bar soap. Wash.
• Do not overfill fabric softener dispenser and do not pour liquid
• Do not overfill fabric softener dispenser and do not pour liquid
fabric softener directly onto fabric.
See page 12 for more instructions.
See page 12 for more instructions.
Black or Gray
marks on
clothes
marks on
clothes
• A buildup caused by the
interaction of fabric
softener and Detergent
can flake off and mark
clothes
softener and Detergent
can flake off and mark
clothes
• Not enough Detergent
• Refer to the recommendations against Scrud(waxy buildup).
(refer to scrud page12.)
• Use correct amount of Detergent for load size, amount of soil
and water Hardness.
Yellow or
brown rust
stains
brown rust
stains
• Iron or manganese in
water supply, water
pipes, or water heater
pipes, or water heater
• To restore discolored load of whites, use rust remover safe for fabric.
• Install nonprecipitating water softener or an iron filter in your
• Install nonprecipitating water softener or an iron filter in your
water supply system for an ongoing problem.
• Before washing, run water for a few minutes to clear lines.
Lint
• Incorrect sorting
• Tissues left in pocket
• Overloading the washer
• Tissues left in pocket
• Overloading the washer
• Wash lint givers eg towels, flannelette sheets, separately from
lint collectors eg synthetic fabrics and remove tissues in pockets
before wash. See page 9 for sorting and caring before loading.
before wash. See page 9 for sorting and caring before loading.
• Do not overload the washer
Residue or
Detergent
Detergent
• Overloading the washer
• Undissolved Detergent
• Too much Detergent
• Undissolved Detergent
• Too much Detergent
• Do not overload the washer.
• Some Detergents need to be pre-dissolved, check the Detergent
• Some Detergents need to be pre-dissolved, check the Detergent
instructions. Try pre-dissolving the detergent in warm water.
• Increase Water Temperature using HOT water safe for fabric.
• Use proper amount of Detergent.
• Use proper amount of Detergent.
Holes, tears,
or snags
or snags
• Incorrect use of chlorine
bleach.
• Unfastened zippers,
hooks, buckles
• Ribs, tears and broken
threads
• Overloading the washer
• Degradation of fabric
• Degradation of fabric
• Never pour chlorine bleach directly on fabric.
See page 11 for adding liquid bleach.
• Fasten zippers, hooks, and buckles.
• Remove objects in pockets. See page 9 for caring before
• Remove objects in pockets. See page 9 for caring before
loading.
• Do not overload the washer.
39
4-7. TROUBLE SHOOTING METHODS ACCORDING TO ERROR MESSAGE
For more detailed information for trouble shooting refer to page 46 to 57.
Symptom
Water Supply
Failure
Failure
Error Message
Check up
• Is the water tap shut off?
• Is the water supply cut off?
• Is the tap or water supply hose frozen?
• Is the water pressure low or is the filter of the inlet valve
• Is the water supply cut off?
• Is the tap or water supply hose frozen?
• Is the water pressure low or is the filter of the inlet valve
clogged with impurities?
• Is the Hot hose connected to cold?
• Is the Cold hose connected to hot?
• Is the Cold hose connected to hot?
If the Washing Machine is subjected to an unstable supply
of water , " " is on the DISPLAY.
of water , " " is on the DISPLAY.
Drainage Failure
• Is th drain hose positioned correctly?
• Is the drain hose bent or placed too high?
• Is the internal part of the hose or drain pump (only pump
• Is the drain hose bent or placed too high?
• Is the internal part of the hose or drain pump (only pump
model) clogged with impurities?
• Check if power has gone off.
Spin Failure
• Is the laundry evenly balanced?
• Is the washing machine placed on a flat surface?
• Is too much soap being used.
• Is the washing machine placed on a flat surface?
• Is too much soap being used.
Door(Lid) Open
• Is the lid closed?
Abnormal level
sensing
sensing
Overflow failure
Abnormal motor
Brake Resister Error
Clutching Error
Coupling Error
• Please call your nearest LG Electronics service center for
help.
Click on the first or last page to see other T1209DB / T1209DS / T1409DB / T1409DS service manuals if exist.