LG GL-4312WT Service Manual ▷ View online
28
Remove the back cover.
Take off the belt turning the pulley.
Unscrew the bolt to pull out the pulley.
Unscrew 2 screws from the bracket.
Push the motor in the arrow direction for
disassembling.
When reassembling the motor, make sure that motor
mounting bushings are not taken off from the bracket.
Pull out the hinge, pressing its snap.
Do not use the pulled - out hinge again. It may be
taken off during operation.
Hinge,
Damper
Damper
Damper
1
2
3
PULLEY, MOTOR, DAMPER
(PULLEY)
(MOTOR)
(DAMPER)
Open the lower cover cap (
) by
using a coin. Turn the drain plug
(
(
) to pull out the hose.
Unplug the drain plug (
) , then
the water flows out,
At this time use a vessel
To prevent water from flowing on
the floor. If the water does not flow
any more,turn the pump filter (
At this time use a vessel
To prevent water from flowing on
the floor. If the water does not flow
any more,turn the pump filter (
)
open to the left.
Take out any foreign material
from the pump filter (
from the pump filter (
). After
cleaning, turn the pump filter(
)
clockwise and insert the
drain plug (
drain plug (
)to the original
place. close the lower cover cap.
Clean the drain pump filter
1
100
2
3
2
3
29
Pump Outlet Hose
Tub Pump
Bellows
Bellows
Remove pump outlet hose.
Remove tub pump bellows.
Remove cap (Remaining Hose.)
Disconnect the wiring.
Unscrew 2 screws.
Remove the pump.
Loosen the M6 heater nut to pull out the heater.
When mounting the heater, be sure to insert the heater
into the heater clip on the bottom of the tub.
Pull it out by holding the thermistor bracket.
If it is pulled by the wire, it may be broken.
When mounting the thermistor again, make sure that it
is got back tight to the bushing.
PUMP
HEATER
THERMISTOR
CAUTION
30
SWITCH ASSEMBLY, DOOR LOCK
WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB
Take apart the cabinet cover clamp and release
the gasket.
Unscrew 2 screws holding the door lock.
Disconnect the door lock from the wiring connector.
Remove the heater.
Remove the foreign material (wire, coin and others) by
inserting a long bar through the hole.
QC MODE CHECK FUNCTION
Push the Power Key when push the Time and
Option 1 Key(Rinse+,Prewash) at the
same time. The Buzzer work 2 times and the program go into TEST MODE.
You can see the Display from the window(Ex.18:A1 etc…)
You can see the Display from the window(Ex.18:A1 etc…)
LOOK
Size
rpm
Display
Konsul_best1
(rotary)
1000RPM
360mm
440mm
550mm
1000rpm
1000rpm
1000rpm
18:A1
18:A6
18:Ab
Konsul_best2
(rotary)
800RPM
360mm
440mm
550mm
800rpm
800rpm
800rpm
18:b0
18:b5
18:bA
Konsul_better1
(tect)
1000RPM
360mm
440mm
550mm
1000rpm
1000rpm
1000rpm
18:C1
18:C6
18:Cb
Konsul_better2
(tect)
800RPM
360mm
440mm
550mm
800rpm
800rpm
800rpm
18:d0
18:d5
18:dA
Display
18：E1
18：E6
18：Eb
18：H0
18：H5
18：HA
18：F1
18：F6
18：Fb
18：L0
18：L5
18：LA
Worldwide
Australia
LOOK
Size
rpm
表示
Konsul_best1
(rotary)
1200RPM
360mm
440mm
550mm
1200rpm
1200rpm
1200rpm
18:A2
18:A7
18:AC
Konsul_better1
(Tact)
1200RPM
360mm
440mm
550mm
1200rpm
1200rpm
1200rpm
18:C2
18:C7
18:CC
-1200RPM Worldwide
Click on the first or last page to see other GL-4312WT service manuals if exist.