DOWNLOAD Sony NEX-VG900 / NEX-VG900E (serv.man2) Service Manual ↓ Size: 10.23 MB | Pages: 35 in PDF or view online for FREE

Model
NEX-VG900 NEX-VG900E (serv.man2)
Pages
35
Size
10.23 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
nex-vg900-nex-vg900e-sm2.pdf
Date

Sony NEX-VG900 / NEX-VG900E (serv.man2) Service Manual ▷ View online

NEX-VG900/VG900E_L2
Sony Corporation
SERVICE MANUAL
Revision History
LEVEL 
2
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2012.10
Official Release
1.1
2012.12
Revised-1
(A1 12-285)
•  Correction of REPAIR PARTS LIST.
 Page 
2-12
Yes
1.2
2013.08
Revised-2
(A2 13-082)
•  Change of REPAIR PARTS LIST.
   Page 
2-15
Yes
SERVICE  NOTE (Check the following note before the service.)
983469533.pdf
2013H08-1
© 2013.08
Published by Sony Techno Create Corporation
Ver. 1.2  2013.08
INTERCHANGEABLE LENS DIGITAL HD VIDEO CAMERA RECORDER
The components identified 
by mark 
0 or dotted line with 
mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques 
pour la sécurité.
Ne les remplacer que par une 
pièce portant le numéro spécifié.
US Model
Canadian Model
AEP Model
E Model
Chinese Model
Japanese Model
Tourist Model
1-1. 
POWER SUPPLY DURING REPAIRS
1-2. 
PRECAUTION ON REPLACING THE VC-1006 BOARD
1-3. 
PRECAUTION FOR REPLACEMENT OF IMAGER UNIT
1-4.  
NOTES FOR REPLACING THE EVF DISPLAY DEVICE (LCD902) OR THE VC-1006 
BOARD
1-5. 
ADDITION OF DESTINATION DATA FILE
1-6. 
PRECAUTION ON REPLACING THE MB N PLATE AND NDF UNIT
1-7. SELF-DIAGNOSIS 
FUNCTION
1-8. 
METHOD OF COPING WITH LENS ERROR
1-9. 
NOTE ON REPLACEMENT OF MOUNT ADAPTOR (LA-EA3) (SERVICE)
9-834-695-33
– ENGLISH –
– JAPANESE –
1-1. 
修理時の電源供給について
1-2.   VC-1006 基板交換時の注意
1-3. 
イメージャーユニット交換時の注意
1-4.   EVF表示素子(LCD902)
またはVC-1006基板交換時の注意
1-5. 
Destination Data ファイルの追加について
1-6. 
MB NプレートとNDFユニット交換時の注意
1-7. 
自己診断機能
1-8.   レンズエラーの対処方法
1-9. 
マウントアダプター(LA-EA3)(サービス)交換時の注意
NEX-VG900/VG900E
Photo: NEX-VG900
Photo: LA-EA3
Revised-2
Replace the previously issued
SERVICE MANUAL 9-834-695-32
with this Manual.
NEX-VG900/VG900E_L2
– 2 –
SPECIFICATIONS
System
Signal format:
NEX-VG900:
NTSC color, EIA standards
HDTV 1080/60i, 1080/60p specification
NEX-VG900E:
PAL color, CCIR standards
HDTV 1080/50i, 1080/50p specification
NTSC color, EIA standards HDTV 1080/60i
specification (24p recording mode only)
Movie recording format:
HD: MPEG-4 AVC/H.264 AVCHD format
Ver.2.0 compatible
STD: MPEG2-PS
Audio recording system:
Dolby Digital 2ch/5.1ch
Dolby Digital 5.1 Creator
Photo file format
DCF Ver.2.0 Compatible
Exif Ver.2.3 Compatible
MPF Baseline Compatible
Recording media (Movie/Photo)
“Memory Stick PRO Duo” media
SD card (Class 4 or faster)
Viewfinder:
Electronic viewfinder: Color
Screen size: 1.3 cm (0.5 type)
Effective pixel number: 2 359 296 dots
(3 072 × 768)
Image device: 36.1 mm × 24.3 mm (35 mm full
size) CMOS sensor
Recording pixels (still 3:2 JPEG):
Max. 24.0 mega (6 000 × 4 000) pixels
Gross: Approx. 24 660 000 pixels
Effective (movie, 16:9):
Approx. 20 300 000 pixels
Effective (photo, 16:9):
Approx. 20 300 000 pixels
Effective (photo, 3:2):
Approx. 24 300 000 pixels
Color temperature: [Auto], [One Push], [Indoor]
(3 200 K), [Outdoor] (5 600 K), manual
(2 500 K - 9 900 K)
Minimum illumination
8 lx (lux) (in default setting, shutter speed
1/60 second (NEX-VG900) / 1/50 second
(NEX-VG900E), gain: 30 dB, aperture F3.5)
Input/Output connectors
A/V Remote Connector: Component/video and
audio output jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB
NEX-VG900E: output only
Headphone jack: Stereo minijack (ø 3.5 mm)
MIC input jack: Stereo minijack (ø 3.5 mm)
LCD screen
Picture: 7.5 cm (3.0 type, aspect ratio 16:9)
Total number of pixels: 921 600 (1 920 × 480)
General
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
Average power consumption:
During camera recording using viewfinder at
normal brightness:
HD: 5.2 W STD: 5.0 W
During camera recording using LCD screen
at normal brightness:
HD: 4.7 W STD: 4.5 W
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to + 60 °C (–4 °F to
+140 °F)
Dimensions (approx.):
105 mm × 130 mm × 223 mm (4 1/4 in. ×
5 1/8 in. × 8 7/8 in.) (w/h/d) including the
projecting parts
105 mm × 130 mm × 227 mm (4 1/4 in. ×
5 1/8 in. × 9 in.) (w/h/d) including the
projecting parts, supplied battery pack
(NP-FV70) and mount adaptor (LA-EA3)
Mass (approx.)
Camcorder body only:
Approx. 825 g (1 lb 13 oz)
When recording:
Approx. 1 030 g (2 lb 4 oz)
(With supplied battery pack (NP-FV70) and
mount adaptor LA-EA3)
AC Adaptor AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V
Output current: 1.7 A
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to + 60 °C (–4 °F to
+140 °F)
Dimensions (approx.): 48 mm × 29 mm × 81 mm
(1 15/16 in. × 1 3/16 in. × 3 1/4 in.) (w/h/d)
excluding the projecting parts
Mass (approx.): 150 g (5.0 oz) excluding the
power cord (mains lead)
Rechargeable battery pack NP-FV70
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 3.0 A
Capacity
Typical: 14.0 Wh (2 060 mAh)
Minimum: 13.0 Wh (1 960 mAh)
Type: Li-ion
Mount adaptor (LA-EA3)
Dimensions (approx.):
76 mm × 69 mm × 35 mm (3 in. × 2 3/4 in. ×
1 7/16 in.) (w/h/d)
Mass (approx.)
105 g (3.7 oz)
Design and specifications of your camcorder and 
accessories are subject to change without notice.
  Manufactured under license from Dolby 
Laboratories.
– ENGLISH –
– JAPANESE –
概略仕様
システム
信号方式
NTSC
カラー、
EIA
標準方式
HDTV 1080/60i
方式、
1080/60p
方式
ビデオ記録方式
HD
画質:
MPEG-4 AVC/H.264 AVCHD
規格
Ver.2.0
準拠
STD
画質:
MPEG-2 PS
音声記録方式
Dolby Digital 2ch/5.1ch
ドルビーデジタル
5.1
クリエーター搭載
静止画ファイルフォーマット
DCF Ver2.0
準拠
Exif Ver2.3
準拠
MPF Baseline
準拠
記録メディア(動画・静止画)
“メモリースティック
 PRO 
デュオ”
SD
カード(
Class4
以上)
ファインダー
電子ファインダー
画面サイズ:
1.3cm
0.5
型)
有効画素数:
2 359 296
ドット
3 072 
×
 768
相当)
撮像素子:
36.1 mm 
×
 24.3 mm
35mm
フルサイズ)
CMOS
センサー
記録画素数:静止画時
 
最大
2 400
万画素(
 6 000
×
 4 000
3
2
JPEG
総画素数:約
2 466
万画素
動画時有効画素数(
16
9
):約
2 030
万画素
静止画時有効画素数(
16
9
):約
2 030
万画素
静止画時有効画素数(
3
2
):約
2 430
万画素
色温度切り換え:
[オート]、[ワンプッシュ]、[屋内]
3 200 K
)、[屋外]
5 600 K
)、マニュアル
2 500 K - 9 900 K
最低被写体照度:
8 lx
 lux
)お買い上げ時
 
シャッター
スピード:
1/60
、ゲイン:
30dB
、絞り:
F3.5
入/出力端子
A/V
リモート端子:コンポーネント、映像音声出力兼
用端子
HDMI OUT
端子:
HDMI
ミニコネクタ
USB
端子:
mini-AB
ヘッドホン端子:ステレオミニジャック(ø
3.5 mm
MIC
入力端子:ステレオミニジャック(ø
3.5 mm
液晶モニター
画面サイズ:
7.5 cm
3.0
型、アスペクト比
16
9
総ドット数:
921 600
ドット
1 920
×縦
480
電源部、その他
電源電圧:バッテリー端子入力
 6.8 V/7.2 V
DC
端子入力
 8.4 V
消費電力:
ファインダー使用時、明るさ標準:
HD
5.2 W STD
5.0 W
液晶モニター使用時、明るさ標準
HD
4.7 W STD
4.5 W
動作温度:
℃∼
 40 
保存温度:−
20 
℃∼
 +60 
外形寸法:
105 mm 
×
 130 mm 
×
 223 mm
(突起部を含む)
(幅×高さ×奥行き)
105 
×
 130 
×
 227 mm
(突起部、付属バッテリー
(NP-FV70)
、マウント
アダプター(
LA-EA3
)を含む)
(幅×高さ×奥行き)
本体質量:
本体質量
 
825g
撮影時総質量
 
1 030g
(付属バッテリー
(NP-FV70)
、マウントアダプター
LA-EA3
)含む)
ACアダプター AC-L200D
電源:
AC 100 V - 240 V
50 Hz/60 Hz
消費電流:
0.35 A - 0.18 A
消費電力:
18 W
定格出力:
DC 8.4 V
動作温度:
℃∼
 40 
保存温度:−
20 
℃∼
 +60 
外形寸法:約
 48
×
29
×
81 mm
(最大突起部を除く)
(幅×高さ×奥行き)
質量:約
150 g
(本体のみ)
*その他の仕様については
AC
アダプターのラベルを
ご覧ください。
リチャージャブルバッテリーパック
NP-FV70
最大電圧:
DC 8.4 V
公称電圧:
DC 6.8 V
容量:
公称容量:
14.0 Wh
2 060 mAh
定格(最小)容量:
13 Wh
1 960 mAh
使用電池:
Li-ion
マウントアダプター(LA-EA3)
外形寸法:
76 
×
 69 
×
 35 mm
(幅×高さ×奥行き)
質量:約
105g
本機やアクセサリーの仕様および外観は、改良のた
め予告なく変更することがありますが、ご了承くだ
さい。
 
ドルビーラボラトリーズからの実施権に基づき製
造されています。
Model information table 
 
Model
NEX-VG900
NEX-VG900E
Destination
US, CND, E, J
AEP, E, CH, JE
COLOR system
NTSC
PAL
Internal Recording media
-
-
Lens
-
-
Projector
-
-
GPS
-
-
Hot shoe
-
-
Charging capacitor (for flash)
-
-
•   Abbreviation 
 
  CH   : Chinese model 
 
  CND   : Canadian model 
 
  J  
: Japanese model 
 
  JE  
: Tourist model 
 
NEX-VG900/VG900E_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Caution
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health 
and environment, and wastes resources.
Manage the chemicals carefully as follows.
•  Store chemicals sealed in a specific place to prevent from exposure 
to high temperature or direct sunlight.
•  Avoid dividing chemicals into excessive numbers of small containers 
to reduce natural evaporation.
•  Keep containers sealed to avoid natural evaporation when chemicals 
are not in use.
•  Avoid using chemicals as much as possible. When using chemicals, 
divide only required amount to a small plate from the container and 
use up it.
PLASTIC PARTS
Be careful to the following points for plastic parts used in this unit.
•  Use a piece of cleaning paper or cleaning cloth for cleaning plastic 
parts. Avoid using chemicals.
 
Even if you have to use chemicals to clean heavy dirt, don’t use paint 
thinner, ketone, nor alcohol.
•  Insert the specific screws vertically to the part when installing a 
plastic part.
 
Be careful not to tighten screws too much.
UNLEADED  SOLDER
This unit uses unleaded solder. 
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•  Set the soldering iron tip temperature to 350 °C approximately.
 
If cannot control temperature, solder/unsolder at high temperature 
for a short time.
 
Caution: The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!
 
 
Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.
•  Be sure to control soldering iron tips used for unleaded solder and 
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Keep the temperature of the soldering iron around 350 °C during 
repairing.
 
•   Do not touch the soldering iron on the same conductor of the circuit 
board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering or 
unsoldering.
各種薬品の取り扱いについて
現在使用されている薬品の中には揮発性の高い薬品もありま
す。
それらを不用意に取り扱い蒸発させてしまうと,環境や健康へ
影響を与えたり,資源の無駄使いになります。
各種薬品は,下記の点に注意して取り扱ってください。
・ 
保管場所を定め,高温になったり直射日光の当たらない場
所に密閉して保管してください。
・ 
小分け(ハンドラップ等)する数は必要最小限に留め,容器
による自然蒸発を防いでください。
・ 
作業に使用しない時は,必ずキャップ等をして自然蒸発を
防いでください。
・ 
薬品を使用する回数を極力少なくし,使用する場合は使用
する量だけ容器より出して受け皿に残さないようにしてく
ださい。
樹脂系部品の取り扱いについて
本機に使用されている樹脂系の部品は,下記の点に注意して取
り扱ってください。
・ 
清掃には薬品を使用せず,清掃紙や清掃布を使用してくだ
さい。
 
やむを得ず汚れがひどくて薬品を使用する場合は,シン
ナー,ケトン,エーテルは使用しないでください。
・ 
各部品の取り付けには指定されたねじを使用し,部品に対
して垂直に取り付けてください。
 
また,ねじを締め付ける時は,無理な力を加えないでくだ
さい。
1.  注意事項をお守りください。
 
サービスのとき特に注意を要する個所については,キャビ
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書きおよび取扱説明書等の
注意事項を必ずお守りください。
2.  指定部品のご使用を
 
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用してください。特に回路図,
部品表に
0
印で指定されている安全上重要な部品は必ず指
定のものをご使用ください。
3.  部品の取付けや配線の引きまわしはもとどおりに
 
安全上,チューブやテープなどの絶縁材料を使用したり,
プリント基板から浮かして取付けた部品があります。
 
また内部配線は引きまわしやクランパによって発熱部品や
高圧部品に接近しないよう配慮されていますので,これら
は必ずもとどおりにしてください。
4.  サービス後は安全点検を
 
サービスのために取外したネジ,部品,配線がもとどおり
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認してください。
5.  チップ部品交換時の注意
 
・  取り外した部品は再使用しないでください。
 
・  タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意してください。
6.  フレキシブルプリント基板の取扱いについて
 
・  こて先温度を350℃に設定して行ってください。
 
・  同一パターンに何度もこて先を当てないでください。
 
  (3回以内)
 
・  パターンに力が加わらないよう注意してください。
サービス,点検時には次のことにご注意ください。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
(注意: 基板サイズによっては,無鉛半田を使用していてもレッ
ドフリーマークがプリントされていないものがありま
す)
:レッドフリーマーク
無鉛半田は,下記の点に注意して使用してください。
・ 
半田こてのこて先温度は約350℃に設定してください。
 
温度調節が無理な場合は,高温短時間で作業を行ってくだ
さい。
 
注意: 半田こてを長く当てすぎると,基板のパターン(銅
箔)がはがれてしまうことがありますので,注意して
ください。また,従来の半田よりも粘性が強いため,
IC端子などが半田ブリッジしないように注意してく
ださい。
・ 
半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け
て管理してください。
 
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
– ENGLISH –
– JAPANESE –
1-1
NEX-VG900/VG900E_L2
1. SERVICE  NOTE
1-1.  POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 Vdc), the power is shut off 
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2.  PRECAUTION ON REPLACING THE VC-1006 BOARD
Note the following when replacing the board.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
USB Serial No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Imager DRA Data
Extract the imager data from the set before the VC board replacement using “Imager DRA Data Reference” in the DATA tab of the Adjust manual.
After the VC board has been replaced, write the data extracted from the set before the VC board replacement in the set using “Imager DRA Data Input” 
in the ADJUST tab of the Adjust manual.
EVF WB Adjustment data value
WB adjustment values of each EVF display device (LCD902) are stored on the VC board.
Therefore, when the LCD902 or the VC board has been replaced, write WB adjustment values.
Product ID
The unit is shipped after an ID (PRODUCT ID) unique to each model has been written.
This ID is not written to a new replacement board. Enter a unique ID after the board has been replaced.
Start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB SERIAL No. INPUT”.
Setting PRODUCT ID
No PRODUCT ID is set for a new replacement board.
Therefore, if the board is replaced with a new replacement board, a discrepancy with the user-registered PRODUCT ID provided by the customer
may be generated.
After the board has been replaced with a new replacement board, start Adjust Manual from Adjust Station and execute “PRODUCT ID & USB 
SERIAL No. INPUT”.
1-3.  PRECAUTION FOR REPLACEMENT OF IMAGER UNIT
In this model, the following procedure is required when the imager unit is replaced.
•  In the case that the imager data can be extracted from the set before the replacement, refer to “Imager DRA Data” in “1-2. PRECAUTION ON 
REPLACING THE VC-1006 BOARD”.
•  In the case that the imager data cannot be extracted from the set before the replacement, replace both VC board and imager unit.
  Capture the data to PC from CD-ROM supplied with the imager unit when it is ordered.
  Write the captured data in the set using “Imager DRA Data Input” in the ADJUST tab of the Adjust manual.
  After all adjustment items have been completed, execute “Phase Detection AF Check” on the SERVICE tab of the Adjust manual.
– ENGLISH –
1-4.  NOTES FOR REPLACING THE EVF DISPLAY DEVICE (LCD902) OR THE VC-1006 BOARD
WB adjustment values of each EVF display device (LCD902) are stored on the VC board.
Therefore, when the LCD902 or the VC board has been replaced, write WB adjustment values.
Adjustment
value
1-A
1-A
When LCD902 is replaced:
1.  Check and write down the adjustment values printed on the LCD902 label.
2.  After the LCD902 has been replaced, execute “EVF WB Adj” on the ADJUST tab by using the Adjust manual to write the adjustment values.
When replacing VC board (in case adjustment values can be read):
1.  In case the unrepaired unit starts and adjustment values can be read by using the Adjust manual, execute “ADJUSTMENT DATA BACKUP” on 
the DATA tab.
2.   After the VC board has been replaced with a VC board for repair, execute “ADJUSTMENT DATA BACKUP” on the DATA tab of the Adjust 
manual to write the extracted data to the unit.
When replacing VC board (in case adjustment values cannot be read):
1.   When adjustment values cannot be read from the unrepaired unit, disassemble the unit and write down the adjustment values printed on the LCD902 
label.
2.   After the VC board has been replaced with a VC board for repair, execute “EVF WB Adj.” on the ADJUST tab by using the Adjust manual to write 
adjustment values to the unit.
1-5.  ADDITION OF DESTINATION DATA FILE
If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
Note 1:  To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
 
Install the Adjust manual of the DSC-WX50 series in advance.
Note 2:  The actual image may differ from the image shown above.
1)  If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed.
 
Click the [OK] button.
 
 Fig. 
1
2)  The Destination Data Write window opens.
 
Check the version of the Destination Data file retained in the Adjust manual.
 
Destination Ver. window
Page of 35
Display

Sony NEX-VG900 / NEX-VG900E (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sony NEX-VG900 / NEX-VG900E (serv.man2) Service Manual ↓ Size: 10.23 MB | Pages: 35 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony NEX-VG900 / NEX-VG900E (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sony NEX-VG900 / NEX-VG900E (serv.man2) Digital Camera. Information contained in Sony NEX-VG900 / NEX-VG900E (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.