LG F96400WHR Service Manual ▷ View online
26
7-6. TROUBLESHOOTING WITH ERROR
Water Inlet Error (IE)
Is the water tap closed?
[Note] Environmental safety check list
1. No water tap leakage or freeze 4. No entanglement of water supply hose.
2. No water shortage. 5. No water supply hose leakage
3. The inlet filter is not cloggeed.
Check the
Water tap
and open it fully.
When there is water in the tub,
is the water level frequency
over 26.0khz?
is the water level frequency
over 26.0khz?
Reconnect or repair the
Connector
.
Or replace the
Harness
.
Replace the
Inlet Valve
.
Is the
Connector
connected correctly to the
Main PCB
and the
Inlet Valve
? is the
Harness
alright ?
Check the
Air Chamber
and
the Tube
(clogged)
Check the water level frequency again,
if it is over 26.2KHz, replace
if it is over 26.2KHz, replace
the Pressure switch.
YES
YES
NO
Replace the
Main PCB
.
NO
YES
YES
NO
NO
Is the resistance of each lnlet valve within 3.5 ~4.5 kΩ ?
When the washing machine is started, is the inlet valve
operating?
operating?
Pre Valve
Steam Valve
Main Valve
1
2
1
2
3
3
NO
27
Unbalanced Error (UE)
Does the load lean toward one
side
side
, or is the load a few items?
Is the washing machine installed
at an angle?
at an angle?
Adjust the height of washing
machine to be kept horizontally.
( Page 8)
machine to be kept horizontally.
( Page 8)
Is the laundry mixed?
The few items of clothing will clump together
and their weight will be in one place on the drum,
throwing the weight off during spin mode.
So add some laundry to overcome UE error.
and their weight will be in one place on the drum,
throwing the weight off during spin mode.
So add some laundry to overcome UE error.
And rearrange load to allow proper spinning.
Try rearranging the laundry in drum
Or the laundry is separated by size, type, and color.
Or the laundry is separated by size, type, and color.
Separate by size,
type and color
YES
YES
NO
NO
YES
28
Water Outlet Error (OE)
Is the drain hose kinked ?
Check drain hose for kink and straighten the
Hose
.
Drain Hose
Is the
Pump filter
clogged ?
Next Page
Check & Clean
Pump Filter
.
YES
YES
NO
NO
This kind of accumulation on the drain filter not only
prevents proper drainage, but also will promote
bacteria growth and cause odors.
This drain filter should be cleaned once a month.
prevents proper drainage, but also will promote
bacteria growth and cause odors.
This drain filter should be cleaned once a month.
* How to disassemble and clean pump filter
Open the Cover by coin or
finger(only new model)
finger(only new model)
Cover
Drain water by removing the
hose cap.
hose cap.
Disassemble the pump
filter by turning the filter
cap counterclockwise.
filter by turning the filter
cap counterclockwise.
Filter clogged by foreign objects
Assemble & close cap
Pump Filter
filter Cap
Hose Cap
Clean the filter
Filter Cap
29
Is the
Connector
connected correctly to
the
Main PCB
and the
Pump Motor
?
Or is the
Harness
alright ?
Is the
Standpipe Height
greater
than 1.0 m above the floor?
When there is no water in the
pump casing, is the water level
frequency over 26.0khz ?
pump casing, is the water level
frequency over 26.0khz ?
Observe
Standpipe Height
requirements
of
1.0
m
maximum.
- Your washer will not be able to drain out
water adequately, if the standpipe exceeds 1.0 m.
In this case, water may flow back into the washer.
In this case, water may flow back into the washer.
Check the
Air Chamber
and the
Tube
(clogged).
Check the water level frequency again, if it is over
25.5KHz, replace the
25.5KHz, replace the
If it is clogged, Pressure
switch.
YES
NO
Reconnect or repair the
Connector
.
Or replace the
Harness
.
NO
Replace the
Main PCB
.
NO
Replace the
Pump Motor
.
Is the resistance of the Pump Motor out
of range 152~175Ω?
Or is the Impeller operating normally?
of range 152~175Ω?
Or is the Impeller operating normally?
Does the Pump motor start, when the spin mode
starts?
starts?
Clean the drain hose.
If the drain hose blocked?
Escape
Binding
NO
NO
YES
YES
YES
OR
YES
YES
Click on the first or last page to see other F96400WHR service manuals if exist.