DOWNLOAD LG F96400WHR Service Manual ↓ Size: 15.96 MB | Pages: 66 in PDF or view online for FREE

Is the resistance of the 

out of range 44 ~

53 KΩ at 25°C? (Page 23) 

Replace the 

.

Is the 

connected correctly to 

the 

and the 

and the 

? 

Is the 

alright ?

Reconnect or repair the 

.

Or replace the 

.

Replace the 

.

Replace the 

.

Is the resistance of the 

out of range 24.5 ~

28.5Ω (for Washing) or 42.5 ~ 49.5Ω (for Steam) ?
(Page 25) 

S

P

E

C

Temp

30 °C

40 °C
60 °C

70 °C

95 °C

105 °C

Resistance (kΩ)

MIN

36.35

39.45

42.72

24.20

26.05

27.97

11.43

12.12

12.82

8.088

8.514

8.940

3.544

3.791

4.045

2.617

2.816

3.023

STD

MAX

Are the resistance of the 

5~15kΩ?

[Pre Check]
• Gentle wash cycles, such as Perm Press, Delicates, Hand Wash, and Wool/Silk should only be used for smaller loads.

Because these cycles are more gentle in tumbling and spinning, putting too much in the drum can register an issue
with the motor. Remove items, reset unit and test with a Rinse/Spin cycle.

• Don’t replace the PCB, when the hall sensor is replaced.

Replace the PCB, when the LE is displayed after replacing the hall sensor.

Is the 

connected correctly to 

the 

and the 

?

Is the 

alright ?

Disassemble the 

.

Is the 

of rotor cracked or broken?

: 5 ~ 15 kΩ

: 5 ~ 15 kΩ

Replace the 

.

Press the 

button & 

button.

Does the

stop when the start/pause button is pressed to start the cycle ?

Or Sometimes does the 

rotate weakly (under 15rpm)?

Magnet

Ha

Hb

Common

Is the resistance the same
between 

points?

V~U / U~W / W~V : 8~11Ω

Reconnect or repair the 

.

Or replace the 

.

Replace the 

.

Replace the 

.

Disassemble 

hall sensor carefully. 

Replace the 

.

Disassemble the Hall Sensor

1) Disassemble the hook of Hall Sensor by (-) driver.

2) Pull up  Hall Sensor slowly as shown in picture. 

1) Adjust the hole of Hall Sensor to 

the hooks of stator  as shown in red circle 

2) Push down the Hall sensor, 

and assemble to the hook securely.

If you disassemble by force,not following the directions, 
the hooks of stator(red circled) might  break.
Hence need change of stator assembly. 

So disassemble cautiously.

1

Assemble the Hall Sensor

2

Hall Sensor Part No.
• 24” / 25” : 6501KW2001A

• 27” : 6501KW2002A 

Check if there is some water on the base ?

Which part have broken.(ex.

Tub, dispenser, inlet hose,

circulation hose, steam

generator, pump, drain hose)

Replace the  broken part.

Check if there is some water on the base ?

Assemble the aqua switch.

Reconnect or repair the

connector. Or replace the harnes.

Replace the Aqua switch.

Is the connector connected correctly to the main PCB
and the aqua switch?
Or is the harness alright?

Is Aqua switch assembled correctly to

the base?

When you press and hold  the styrofoam

in the Aqua switch, is AE displayed?