LG F84923WHS / F84933WHS Service Manual ▷ View online
11
Rubber Cup
Check the horizontality with a level (Gage).
8
Step 1
If washing machine legs are loose or not Screwed in, then
tighten
with the spanner wrench.
Using the level, level the washing machine from front to back and side to side.
Step 2
Use the spanner wrench to adjust Legs until level and try the
Diagonal test
.
Step 3
Perform a Rinse and Spin with some clothing in the machine.
To do this, put 2~3kg of clothing in the unit, turn on the unit, Select the Rinse+Spin
and then start. When the unit reaches the spin cycle, watch for vibrations.
If the unit is vibrating, make small adjustments to the leg until they subside. (Repeat step 2)
To do this, put 2~3kg of clothing in the unit, turn on the unit, Select the Rinse+Spin
and then start. When the unit reaches the spin cycle, watch for vibrations.
If the unit is vibrating, make small adjustments to the leg until they subside. (Repeat step 2)
Step 4
Tighten
the lock nut against the base of the machine to
lock
the
position leg
.
Lower the foot until there is no gap between floor and foot.
And only use
And only use
adjustment rubber
when difference at the leg adjustment is more than
10mm
.
Place your right hand on the back, right corner and your left hand on the front,
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right side and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock. However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot under the hand that is on the front of the machine.
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right side and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock. However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot under the hand that is on the front of the machine.
How to perform a diagonal test:
A level
Higher
Tighten
Adjustable feet
Diagonal test
Tighten
Adjustable feet
Higher
Tighten
Adjustable feet
Lower
4620ER4002B
(Gray)
(Gray)
for Wooden floors
Rubber Cup
4620ER4002A
(Black)
(Black)
for Tile floors
Lock nut
10mm
Adjustable bolt
Tighen the lock nut
Floor
No Gap
Floor
No Gap
Floor
Gap
12
Test operation
9
1
Preparation
for
washing.
for
washing.
· Connect the power plug to the
outlet.
· Connect the inlet hose.
2
Press the power button.
3
Press the START/PAUSE
button.
button.
6
Check the water heating.
· Press the left Option + temp
button simultaneously and the
present temperature will be
displayed.
present temperature will be
displayed.
Page 20
· Check if the drum rotates
clockwise and counterclockwise.
5
Check automatic reverse turn.
4
Check the water supply.
· Check if water is supplied through
the detergent dispenser.
7
Check the drain and spin
functions.
functions.
· Turn power off and then power on.
· Select the spin rpm
· Press the START PAUSE button.
· Check the spin and drain
· Select the spin rpm
· Press the START PAUSE button.
· Check the spin and drain
functions.
· Turn power off and then power on.
· Listen for a click to determine if the
· Listen for a click to determine if the
door is unlocking.
8
Turn power off and open
the door.
the door.
9
Water removal.
· If SVC is needed during check,
remove the remaining water by
pulling out the hose cap.
pulling out the hose cap.
· In case of Coloreds program.
13
Cycle Selector
Additional programs
Start/Pause
Option Button
Power
5. OPERATION
14
Button
Use this option to prevent unwanted
use of the washer. Press and hold
Spin button button for 3 seconds
to lock/unlock control.
When Child lock is set, CHILDLOCK
lights and all buttons are disabled
except the Power
button. You can
lock the washer while it is operating.
The Beep on/off function can be set by pressing
and holding the Temp. and Rinse button
This display shows:
a) the estimated time remaining in the
cycle when operating.
EST. T ime remaining
Beep on/off
In case of abormal operation, error
indications are displayed.
(
)
¥ see troubleshooting
simultaneouly.
Tub Clean course can be set by
pressing and holding Rinse button
simultaneously.
Tub Clean is a special cycle to
clean the inside of the washer.
Tub Clean
Select water temperature based
on the load type.
By pressing the Rinse button, the
Rinse type can be selected.
Child Lock
Rinse,
Temp.
Click on the first or last page to see other F84923WHS / F84933WHS service manuals if exist.