DOWNLOAD LG F12695RDH Service Manual ↓ Size: 13.43 MB | Pages: 69 in PDF or view online for FREE

Check the horizontality with a level (Gage).

8

If washing machine legs are loose or not fully attached, then tighten with  the spanner wrench. 
Using the level, level the washing machine from front to back and side to side.

Use the spanner wrench to adjust legs until level and try the Diagonal test.

Perform a Rinse and Spin with some clothing in the machine.
To do this, put 2~3kg of clothing in the unit, turn on the unit, select the Rinse+Spin 
and then start. When the unit reaches the spin cycle, check vibrations.
If the unit vibrates, adjust the leveling foot slightly until the vibration subside. (Repeat step 2) 

Lower the foot until there is no gap between floor and foot.
And only use adjustment rubber when the gap  is more than 10mm.

Place your right hand on the back, right corner and your left hand on the front,
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right corner and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock.  However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot on the front right corner. 

A level

Lower

Tighten

Adjustable feet

Loosen

Adjustable feet

Higher

Tighten

Adjustable feet

Lower

4620ER4002B
(Gray)
for Wooden floors

Rubber Cup

4620ER4002A
(Black)
for Tile floors

Lock nut

10mm

Adjustable bolt

Tighen the lock nut

Floor

No Gap

Floor

No Gap

Floor

Gap

Test operation

9

Preparation
for 
washing.

· Connect the power plug to the

outlet.

· Connect the inlet hose.   

Press the power button.

Press the START/PAUSE
button.

Check the water heating.

· Touch the Temp. and Pre

Wash button simultaneously
to check the present
temperature. 

Page 22

· Check if the drum rotates

clockwise and  counterclockwise. 

Check automatic reverse turn.

Check the water supply.

· Check if water is supplied through

the detergent dispenser.

Check the drain and spin
functions.

· Turn power off and then power on.
· Select the spin rpm
· Press the START PAUSE button.
· Check the spin and drain

functions.

· Turn power off and then power on.
· Listen for a click to determine if the

door is unlocking.

Turn power off and open
the door.

Water removal.

· If SVC is needed during  check,

remove the remaining water by
pulling out the hose cap.

· In case of Coloreds program.

-   

    '

#    

'      

     

  

&*  ' ( .       ' '   '

 /01 

*  ( 2'  #  *     *

3     *      # 

3  ( 3   # *   '    

*4   '     

  ( 

          *

. 01*        

-  ( 3            # '   

-  
&*  ( &           *      # *

&                # *  

 (    '  '       

&* (     *      '   ' 

#

       

 

5. OPERATION (F1695RDH(1~9))

Use this option to prevent unwanted use of the

washer. Press and hold

Dry button button for 3 seconds to lock/unlock

When Child lock is set, CHILD LOCK

lights and all buttons are disabled

except the Power

button.

You can lock the washer while it is operating.

This display shows:

a) the estimated time remaining in the cycle when

In case of abormal operation, error indications are

(

)

¥ see troubleshooting

m.

Tub Clean course can be set by

pressing and holding Spin button

simultaneously.

Tub Clean is a special cycle to

clean the inside of the washer.

The Beep on/off function can be set by pressing

and holding the Wash and Temp. button

simultaneouly.

By pressing the Spin button, the

spin type can be selected.

By pressing the Rinse button, the

Rinse type can be selected.

operating.

displayed.

Time Left

Washing

20%

1600

40

°C

#

Normal

control.