DOWNLOAD LG F1092QDT2 / F1092QDT25 / F1092QDTA5 Service Manual ↓ Size: 20.05 MB | Pages: 45 in PDF or view online for FREE

5. OPERATION

13 programs can be set
depending on the type of
the laundry.
If the power button is
pressed, all lamps are on
By turning the dial, [Cott on -
Cott on Quick - Synthetic -
Duvet - Bulky - Quick 30 -
Rinse+Spin - Spin - Delicate -
Hand Wash/Wool - Bio Care -
Boiling Care - Baby Care ]
can be selected.
This is a bi-directional selector.

Use the button to start or pause wash
cycle.
The power turns off automatically 4
minutes after the pause button is
pressed.

Child Lock system can

be set and canceled by

pressing and holding

both 

butt on

and 

butt on

simu ltaneously more

than 3 seconds.

Tub Clean course can be set by
pressing and holding 

and

button simultaneously.

Tub Clean is special cycle to clean the
inside of the washer.

Medic Rinse : Function that offers more purity in rinse operation by 

maintaining the optimum temperature for elimination of 

remnant detergent. It can be selected in all courses with the 

exception of Quick 30. Hand Wash/Wool, Delicate course.

 If the laundry is heavily soiled “Intensive” option is effect

ive.

 By selecting the Intensive option, the wash time may be 

extended, depending on the program selected.

Pre Wash : If the laundry is heavily soiled, “Pre Wash” course is effective.

Pre Wash is available in Cotton and Synthetic Program.

Crease Care : If you want to prevent crease, select this button with spin

5-1. F**89Q/TDT(P)2(A)(0~9) / F**92Q/TDT(P)2(A)(0~9)

Option

Child -Lock

Wash program selector

Start/Pause button

Tub Clean

Press the button when reservation washing
is needed.
When the button is pressed, [        ] is
displayed, maximum delay of [        ] hours
can be set.
Each press advances time delay by the hour. 
Use [Power] button to cancel [Time Delay]
[Time Delay] means the time required from
the present to the completion of washing.
The Beep on/off function can be set by
pressing and holding the Time Delay button
(About 3 seconds).
The Beep on/off function can be set at any time
and it is automatically cancelled in the event of
a power cut.
The Beep on/off function also works when
power is off.

Press the button to turn power on and off.
Press the button to cancel the time delay.

Page 17

- Press and Hold ‘

’ & ‘

’ buttons and then press ‘

’ button.

- Press and Hold ‘

’ & ‘

’ buttons simultaneousl

y.

By pressing the Spin Button the spin speed

can be chosen

F10**Q/TDT(P)2(A)(0~9)

Rinse Hold/No spin/400/800/1000

F12**Q/TDT(P)2(A)(0~9)

Rinse Hold/No spin/400/800/1200

F14**Q/TDT(P)2(A)(0~9)

Rinse Hold/No spin/400/800/1400

F80**Q/TDT(P)2(A)(0~9)

Rinse Hold/No spin/400/600/800

Display the estimated remaining time 
(Hour : Minute) to finish.
In case of abnormal operation, error indications are
displayed.
(                                                              

              )

See troubleshooting guide.

Press the button to select water temperature.
95°C is selected for Cotton and Baby Care
only.
By pressing the button while operating the
washer, the present temperature is displayed.

6. WIRING DIAGRAM / PCB LAYOUT / PROGRAM CHART

Wiring Diagram

[Note]
RD : Red

YL : Yellow

BL : Blue

WH : White

GY : Gray

BK : Black

VL : Violet

OR : Orange

SBL : Sky Blue

NA : Natural

Display

Display

PCB Power & Heater

Pressure Switch

&

Heater Thermistor

Measure Hz impossible here

Just check cut-off.

Heater Thermistor

(44~53K , 25°C)

Pressure Switch

Common

Drain Pump

&

Door

&

Inlet  alve

Door Switch

Measure R impossible here

Common

Motor

&

Hall Sensor

V ~ U / U ~ W / W ~ V

R : 8 ~11

V   

U  

W

Hb

(5~15k )

Ha

(5~15k )

Common

Drain Pump

(160~177 )

Pre. Valve

(3.5~4.5k )

Main Valve

(3.5~4.5k )

Heater

(24.7~28.0 )

PCB Power

PCB Layout

15

PCB Power & Heater

Heater

(24.7~28.0 )

PCB Power

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω