LG BIDLFL Service Manual ▷ View online
37
NO
2. Water Leak from Dispenser
Are the gasket (seal)
and door cleaned regularly?
and door cleaned regularly?
Is the door or gasket damaged?
Are the inlet hoses loose or cracked/split?
Replace the damaged parts.
Replace the
Inlet Hoses
.
Clean the periphery of
Gasket
and
Door
regularly.
3. Unknown – Water on Floor
YES
Is the washer horizontal ?
Adjust the height of washing machine to be kept
horizontally. (Page 7)
horizontally. (Page 7)
NO
Are the drain filter and manual
drain hose open?
drain hose open?
YES
NO
Check!!
Turn the filter cap clockwise to close.
YES
YES
NO
38
9. DISASSEMBLY INSTRUCTIONS
Disassemble and repair the parts after pulling out power cord from the outlet.
1 Unscrew the screws on the top plate.
3 The cover(Inner) is disassembled.
2 The plate assembly(Top) is pulled back and
then upward to arrow direction.
1 Pull out the drawer and unscrew 2 screws.
2 Lift the side the Control Panel Assembly and
2 Lift the side the Control Panel Assembly and
pull it out
1 Two screws is unscrewed.
2 Push out PANEL ASSEMBLY, CONTROL after
2 Push out PANEL ASSEMBLY, CONTROL after
Push the hook below.
1 The PWB assembly(Display) is disconnected.
2 When 7 screws are unscrewed on the PWB
2 When 7 screws are unscrewed on the PWB
insulator and the PWB assembly(Display) is
disassembled from the PWB insulator.
disassembled from the PWB insulator.
CONTROL PANEL
39
1 The back cover is removed.
2 One screw is unscrewed.
3 Pull the PWB assembly(Main) to arrow
2 One screw is unscrewed.
3 Pull the PWB assembly(Main) to arrow
direction
4 Two screws is unscrewed.
5 The cover of PWB assembly(Main) is
5 The cover of PWB assembly(Main) is
removed.
6 Disconnect connector from the wiring.
PWB ASSEMBLY(MAIN)
1 The plate assembly(Top) disassembled.
2 The cover of PWB assembly(Power) is
2 The cover of PWB assembly(Power) is
removed.
(Push the hook bellow.)
(Push the hook bellow.)
4 Disconnect connector from the PWB.
5 Two screw is unscrewed.
5 Two screw is unscrewed.
PWB ASSEMBLY(POWER)
1 The plate assembly(Top) are disassembled.
3 Two screws are unscrewed.
2 Pull the drawer to arrow direction.
1 The hose clamps and the hose are
disassembled.
2 The ventilation bellows are disassembled on
the tub.
DISPENSER ASSEMBLY
40
VALVE (PRE)
VALVE (MAIN)
VALVE (DRY)
VALVE (HOT)
1 Disconnect the wiring connector.
1
2
3
4
2 Remove the valve by two screws of the valve
holder.
• Rating : 240V 50Hz
• Resistant : 3.5~4.5k
• Resistant : 3.5~4.5k
Ω
When reconnecting the connector
1 Open the door completely.
2 Remove the three screws from the hinge.
2 Remove the three screws from the hinge.
When removing the Door Assembly, it is
necessary to hold the Bracket that is inner of
the Cabinet Cover.
necessary to hold the Bracket that is inner of
the Cabinet Cover.
First, prepare a bucket to put in the remained
water.
water.
Pull it out from hose.
GY/WH - BK
WH/BK - BK
YL/BK - BK
BK/WH - BK
INLET VALVE
DOOR
Removing method of remained water
Click on the first or last page to see other BIDLFL service manuals if exist.