DOWNLOAD LG 41722 Service Manual ↓ Size: 10.47 MB | Pages: 60 in PDF or view online for FREE

5-5. EXPLANATION OF EACH PROCESS

No.

Process

Explanation

1.

Stay

• Electrical power is supplied
• Washer is ready to work and the micom is in the active mode.

2.

Water
supply

• After loading laundry and selecting a course and a cycle, water is

supplied and  drum rotates.

• When a user selects Pre-wash course, water is supplied through 

pre wash valve.

3.

Soaking
& washing
laundry

• To get laundry wet, drum rotates clockwise and counterclockwise.
• If water amount is insufficient at this time, the Inlet valve will supply

water again. 

4.

Heating &
washing

• The heater heats the water in drum to the selected water temperature

and drum rotates for washing. 

5.

~

6.

Washing
& heating
/ washing

• When the water temperature reaches to the selected temperature, the

heating stops and only the drum rotates.

• If water temperature becomes lower than selected because of 

re-supplied water, the heating starts again.

7.

Washing

• Fuzzy Logic decides washing time according to the laundry load, water

temperature, and other factors.

8.

Drainage

• A pump motor drains the water from the drum.
• After sensing drained water amount by water level frequency, spin starts.
• When a heating course is selected, stay cooling process is performed to

decrease the water temperature gradually to prevent laundry from being
damaged and for safety reasons.

9.

Untangling
(Sensing
eccent-
ricity)

• It balances laundry load and senses the eccentricity of the load, to only

allow spinning  without vibration 

• If the eccentricity is worse than the allowed level, it repeats the

disentangling process. When the repeated time is more than allowed
level, it displays UE.

• If the eccentricity is good, the intermittent spin starts.
• During this process, the drain pump works for drainage intermittently.

No.

Process

Explanation

A.

Intermittent
spin

• To reach the correct set speed, the motor rotates clockwise and

counterclockwise directions after spin process starts.

• If the water level frequency is lower than 23.0 kHz, a washer senses

suds and starts suds removal process.

B.

Rinse
spin

• In this process, the remaining water during washing process is

extracted and the selected speed is kept.

• Removing suds process is in active mode at this cycle.

C.

Remaining
spin

• After spin finishes, the drum rotates by remaining spin power until it stops.

Motor power is off.

• This process is overlapped with next process. 

D.

Rinse water
supply

• Water supply for rinse process

E.

Rinse

• Rinsing process.

F.

Last
drainage

• After spin finishes and power is not supplied to motor, the drum

rotates by remaining spin power

• If rinse hold is selected, the drainage is not proceeded after rinse

finishes.

G.

Disentangling

• The same as item 9.

H.

Intermittent spin • The same as item A.

I.

Main spin1

• The same as item B.

J.

Main spin2

• At the end of a main spin, the spin speed will reach the selected rpm.

K.

Remaining spin • The same with item C.

L.

Disentangling

• After spin finishes, disentangling starts to remove unbalanced

laundry.

M.

End

• After 'end' signal is displayed, it stays for 8 seconds and power is

automatically turned off. (Auto type door switch)

• After door switch is off, end signal is displayed in the case of

manual type and it takes around 2 minute to turn off door switch.

6. PROGRAM CHART

Cool-down  

Extra Rinse

Steam Refresh

Sanitize

Bulky

/Bedding

0

2

1
0

0

6

0

2

4

420

420

120

60

420

360

~

720

4

120

120 

59

65

24

23

20

70

12

15

11

8

11

3

63

60

Wo

rkout 

W

ear

Normal/

Casual

41

2

47

51

60

14

20

83

15

103

103

Heavy Duty

Cold Clean

57

  7

  6

47

52

105

20

Express 

W

ash

Hand W

ash

/W

ool

Kid W

ear

Whitest

White

Rugged

14

20

68

18

43

25

57

60

60

7. TEST MODE

7-1. SAFETY CAUTION

There's built-in AC 110V and DC power in output terminal of PWB assembly in common. Be careful electric
shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves when working.)
After cutting off the power when changing PWB assembly, disconnect or assemble.
Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack when delivering
or keeping it. 

7-2. LOAD TEST MODE.

The washer must be empty and the controls must be in the off state. 
1. Press the SPIN SPEED and SOIL LEVEL buttons simultaneously.
2. Press the POWER       button, while the above condition. Then buzzer will sound twice.
3. Press the Steam button.
4. Press the START/PAUSE      button repeatedly to cycle through the test modes.

7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY

Press the WASH/RINSE and DELAY S

button simultaneously.

The digits indicate the water level frequency ( x.1 kHz ).

So, for example a display indicating 241: a Water level frequency of 241 x.1 kHz

=  24.1 kHz

None 

1 time 

2 times 

3 times 

4 times 

5 times 

6 times 

7 times 

8 times 

9 times 

10 times

11 times

Turns on all lamps and locks the door.

Tumble clockwise.

Low speed Spin.

High speed Spin.

It will be take about 2minits to be

high speed spin

Inlet valve for prewash turns on.

Inlet valve for main wash turns on.

Inlet valve for hot water turns on.

Inlet valve for bleach turns on.

Tumble counterclockwise.

Heater turns on for 3 seconds.

Drain pump turns on.

off

LOAD TEST MODE

rpm (42~50)

rpm (35~45)

rpm (110~117)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

rpm (42~50)

Water temperature

Water level (0-255)

-

NOTES:

RPM < 220 : RPM = display / RPM > 200 : RPM = display X 10
WATER LEVEL : o255 = empty / o248 = normal / o255 = tub clean

None 

1 time 

2 times 

3 times 

4 times 

5 times 

6 times 

7 times 

8 times 

9 times 

10 times 

11 times 

12 times 

13 times 

14 times

Turns on all lamps.

Tumble clockwise.

Low speed Spin.

High speed Spin.

Inlet valve for prewash turns on.

Inlet valve for main wash turns on.

Inlet valve for Hot water turns on.

Inlet valve for bleach turns on.

Inlet valve for steam turns on.

Tumble counterclockwise.

Heater turns on for 3 seconds.

Circulation pump turns on.

Drain pump turns on.

Steam water level sensor operates.

Steam Heater turns on for 1.2 sec.

LOAD TEST MODE

rpm (42~50)

rpm (35~45)

rpm (110~117)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

rpm (42~50)

Water temperature

Water level frequency (0~255)

Water level frequency (0~255)

AG tub water level frequency (0~255)

15 times

Vibration sensor check

16 times

off

- None error (bs0)
- Main vibration error (bs1)
- Display vibation error (bs2)
- Both error (bs3)