DOWNLOAD LG 40518 Service Manual ↓ Size: 6.67 MB | Pages: 59 in PDF or view online for FREE

No.

Process

Explanation

A.

Intermittent
spin

• To reach the correct set speed, the motor rotates clockwise and

counterclockwise directions after spin process starts.

• If the water level frequency is lower than 23.0 kHz, a washer senses

suds and starts suds removal process.

B.

Rinse
spin

• In this process, the remaining water during washing process is

extracted and the selected speed is kept.

• Removing suds process is in active mode at this cycle.

C.

Remaining
spin

• After spin finishes, the drum rotates by remaining spin power until it stops.

Motor power is off.

• This process is overlapped with next process. 

D.

Rinse water
supply

• Water supply for rinse process

E.

Rinse

• Rinsing process.

F.

Last
drainage

• After spin finishes and power is not supplied to motor, the drum

rotates by remaining spin power

• If rinse hold is selected, the drainage is not proceeded after rinse

finishes.

G.

Disentangling

• The same as item 9.

H.

Intermittent spin • The same as item A.

I.

Main spin1

• The same as item B.

J.

Main spin2

• At the end of a main spin, the spin speed will reach the selected rpm.

K.

Remaining spin • The same with item C.

L.

Disentangling

• After spin finishes, disentangling starts to remove unbalanced

laundry.

M.

End

• After 'end' signal is displayed, it stays for 8 seconds and power is

automatically turned off. (Auto type door switch)

• After door switch is off, end signal is displayed in the case of

manual type and it takes around 2 minute to turn off door switch.

6. PROGRAM CHART

61

11

20

16

22

34

40

19

75

63

20

97

20

80

59

59

100

25

44

50

Heavy Duty

Normal /Casual

Sanitize

Bulky /Bedding

Whitest Whites

Cold Clean

Express W

ash

Kids wear

120

120

120

120

120

NOTE: Cycles are dif

ferent depending on the models

53

59

11

26

23

20

58

20

53

100

Handwash

/wool

Rugged

W

orkout wear

Steam Refresh

120

120

120

120

120

NOTE: Cycles are dif

ferent depending on the models

7. TEST MODE

7-1. SAFETY CAUTION

There's built-in AC 110V and DC power in output terminal of PWB assembly in common. Be careful electric
shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves when working.)
After cutting off the power when changing PWB assembly, disconnect or assemble.
Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack when delivering
or keeping it. 

7-2. LOAD TEST MODE.

The washer must be empty and the controls must be in the off state. 
1. Press the SPIN SPEED and SOIL LEVEL buttons simultaneously.
2. Press the POWER       button, while the above condition. Then buzzer will sound twice.
3. Press the START/PAUSE      button repeatedly to cycle through the test modes.

7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY

Press the WASH/RINSE and DELAY S

button simultaneously.

The digits indicate the water level frequency ( x.1 kHz ).

So, for example a display indicating 241: a Water level frequency of 241 x.1 kHz

=  24.1 kHz

None 

1 time 

2 times 

3 times 

4 times 

5 times 

6 times 

7 times 

8 times 

9 times 

10 times

11 times

Turns on all lamps and locks the door.

Tumble clockwise.

Low speed Spin.

High speed Spin.

It will be take about 2minits to be

high speed spin

Inlet valve for prewash turns on.

Inlet valve for main wash turns on.

Inlet valve for hot water turns on.

Inlet valve for bleach turns on.

Tumble counterclockwise.

Heater turns on for 3 seconds.

Drain pump turns on.

off

LOAD TEST MODE

rpm (42~50)

rpm (35~45)

rpm (110~117)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

rpm (42~50)

Water temperature

Water level (0-255)

-

NOTES:

RPM < 220 : RPM = display / RPM > 200 : RPM = display X 10
WATER LEVEL : o255 = empty / o248 = normal / o255 = tub clean