DOWNLOAD LG 29278 Service Manual ↓ Size: 9.35 MB | Pages: 46 in PDF or view online for FREE

Allows a selection to be

make for the strength of the

wash action.

Power option selections light

up insequence as follows

Normal ▶ Heavy  ▶ Light
▶ Normal as the button is

pushed.

This can be selected for any

program.

Adjustment can be made

while washing.

Default SOIL LEVEL is

Normal.

Select to select Water

(Wash/Rinse)

Temperature.

Pressing the button allows

The selection of

COLD/COLD ▶

WARM/COLD ▶

WARM/WARM ▶

HOT/COLD ▶ EXTRA

HOT/COLD respectively.

Default setting is

Warm/Cold.

Delayed finishing time.

The time increases when the button is pushed.

The following settings are indicated as the button is

pushed 1 ▶ 2 ▶3 ▶ 4 ▶ ... 17▶ 18 ▶ 19▶
▶ Reservation off ▶ 1 ...

To cancel delay time, turn the power switch off or

push DELAY WASH button until off.

Causes the

dispensing of

fabric softener in

the final rinse

cycle.

Runs a cycle

without hot

water or the

wash heater,

For greater

efficiency, we

recommend

washing a small

load (less than 8

pounds) and a

low spin speed. 

Use to start or pause the wash

cycle.

Changes while be made to the

wash settings while the machine is

paused.

Repeats start and pause by

pushing the button.

Use for selecting wash program.

This button allows the selection

of 10 different programs for

different kinds of laundry and

dirtiness.

Program selections light up in

sequence as follows:

Normal/Casual

▶Cold Clean▶

Heavy duty▶Bulky/bedding▶

Whitest Whites▶Rinse/Spin▶

Sanitize▶Kids Wear▶Towels▶

Workout Wear▶Colors▶

Express Wash▶Handwash/Wool

Delicates select the desired

program by ressing the button.

MYCYCLE allows you to

store a customized wash

cycle for future use. It allows

you to save favorite tempera-

ture, spin speed, soil level,

and other options for a

cycle,and then recall them at

the touch of a button.

Before washer is

operating. Use when

you want only spin,

While washer is

operating. If you

press 5second.all

controls except

CONTROL LOCK

and POWER buttons

will be disabled. If you

want to deactivate.

press it again

5second

When there is the possibility of freezing temperatures

• Close the water taps and remove the water supply hoses.
• Remove the water which remains in the water supply.
• Lower the drain hose and drain the water in the sump and the drain hose by running a spin cycle. 

Cleaning the inside of your washer

If you use fabric softener or do regular COLD water washing, it is very important that you
clean the inside of your washer occasionally as described below. 
• Fill your washer with HOT water.
• Add 1 cup of bleach. 
• Let it operate for several minutes.
• Stop the washer, open the lid, and leave it to soak overnight.
• After soaking, drain the washer and run it through a normal cycle.

Products that might damage your washing machine

• Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of

your washer.

• Hydrocarbon solvents, i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and

blister paint.
(Be careful when washing garments stained with these solvents as they are flammable, DO NOT put
them in washer or dryer.)

• Some pretreatment sprays or liquids can damage your washer’s control panel.
• Use of dyes in your washer may cause staining of the plastic components. The dye will not damage

the machine but we suggest you thoroughly clean your washer afterwards. We do not recommend
the use of dye strippers in your washer.

• Do not use your washer lid as a work surface.

If frozen

• Remove the water supply hose and immerse it in HOT water. (40° C or 104° F).
• Pour approximately 2 liters (4

½ pounds ) of HOT water (40° C or 104° F) into the sump and allow it ti stand for

at least 10 minutes. 

• Connect the water supply hose to the water tap run a SPEED WASH cycle to confirm that the machine fills,

drains, and operates properly. 

Leave the lid open after washing to allow moisture to evaporate. If you
want to clean the inner-tub use a clean soft cloth dampened with liquid
detergent, then rinse. (Do not use harsh or gritty cleaners.)

Hoses connecting washer to faucet should be replaced every 5 years.

Immediately wipe off any spills. Wipe with damp cloth. Avoid hitting surface with sharp objects.

Be sure water supply is shut off at faucets. Drain all water from hoses if weather will be
below freezing.

WIRING DIAGRAM

4

AT

C

3

3

13

1

PRESS  S/W

24

2

4

25

5

6

COLD

5

62

MAIN PCB 

ASSEMBL

Y

HALL

 SENSOR

4

BL

1

21

12

3

2
1

5

1

JET SPRA

Y

HOT

SOFTNER

BLEACH

1

6

DRAIN PUMP

CLUTCH MOT

OR

12

3

6
3

BL

BL

BL

BL

OR

BN

BL
BK

YL

GY

GN/YL

BK

YL

WH
RD

GN/YL (GN)

BL

YL

YL

BL(WH)

HEA

TER

RD

YL

BL

BN

BK

BN

RD

BK

BN(BK)

WH

WH

OR

RD

BL
BN

BL

RD

GY

BL

YL

WH

WH

YL

VL

S K Y

GY

61

2

4

5

3

NOISE FIL

TER

WH

GY

BL

32

1

3
2
1

3

2

1

3

2

1

WH

GY

BN

BL

RD

YL

WH

BL

RD

YL

WH

WH

BL

BL

21

3

1

2

3

12

3

1

2

3

6

1

24

5

3

DOOR LOCK

2
14

5

6

3

7

56

7

4

8

2
14

5

6

37

CON1

DISPLA

Y PCB 

ASSEMBL

Y

GY

BL

WH

BN

1

2

BK

WH

YL

12 BK

WH

12

OVERFLOW SENSOR

3

1

2

12

3

4

567

8

CON2

4
3

BL

Thermostat

WH

WH

YL

RD

COLOR CODE

LETTERS

COLOR

LETTERS

COLOR

WH

WHITE

RD

RED

BK

BLACK

GY

GYAY

BN

BROWN

GN

GREEN

OR

ORANGE

VL

VIOLET

PK

PINK

YL

YELLOW

BL

BLUE

SKY

SKY BLUE

※

WT5001CW dosen’t have 

part.