DOWNLOAD LG 50PQ100R-ZA (CHASSIS:PP91A) Service Manual ↓ Size: 9.62 MB | Pages: 68 in PDF or view online for FREE

(6) Select SW file (XXXX.bin) you want, push the “OK” Key.
(7) S/W download process is excuted automatically.

Tool Option
Area Option
Option 1
Option 2
Option 3(Available for EU & Non EU model)

*  Profile:  Must  be  changed  the  option  value  because  being

different  with  some  setting  value  depend  on  module,  inch
and market 

* Equipment : Adjustment Remote Controller

(1) Push the IN-START key in the Adjust R/C.
(2) Enter Password number. The value of Password is “0 0 0

0”.

(3)  Input  the  Option  Number  that  was  specified  in  the  BOM,

into the Shipping area.

(4)  Select  “Tool  Option/  Area  Option”  by  using 

D

/

E

(CH+/-)

key, and press the number key(0~9) consecutively

(5) if it is EU model ( such as 42/50PQ**R-ZA ), select “Area

option” by using 

D

/

E 

(CH+/-) key , and press the number

key(0~9) consecutively.
ex)  If  the  value  of  Tool  Option1  is  4,  input  the  data  using

number key “4” (Fig. 3)

Caution:  Don’t  Push  “IN-STOP”  key  after  PCB  assembly

adjustment.

(5) EDID D/L Method

After  software  D/L  or  PCBA  manufacturing,  you  can
download EDID Data.
When  you  adjust  Tool  Option,  H6  Model  EDID  download
process is executed automatically

* If the model don’t have HDMI 3, HDMI 3 will be disappeared

at OSD Window.

Caution: When you adjust tool option, don’t connect HDMI or D-

sub cable. 
If  you  connect  some  cable,  EDID  D/L  process  will  be
failed. 

(6) Adjustment method    

Before PCBA check, have to change the Tool option and Area
option  

[ About PDP

After  done  all  adjustments,  Press  IN-START  button  and
compare Tool option and Area option value with its BOM, if it
is  correctly  same  then  Change  “RF  mode”  and  then  unplug
the AC cable.
If it is not same, then correct it same with BOM and unplug AC
cable. 
For correct it to the model’s module from factory JIG model.

[ Don’t push The IN-STOP KEY after completing the function

inspection.

[ Appendix - EDID (The Extended Display Identification Data )

Caution: Never Use the cable( HDMI or D-sub cable) for EDID

Writing. Automatically H6 Model EDID download
process is executed when you adjust Tool Option.

- 9 -

..

..

MODEL : XXXXXX     Module : XXXX
S/W Ver. : X.XX          ROM : XXXXXXX
UTT                X           Temp : xxxxx : Celsius
ADC CAL.
RGB :WW

    OK  

Component SDW

    OK 

Component HDW

    OK 

EDID    RGB(OK)  HDMI1(NG)  HDMI2(NG)  HDMI3(NG)

Tool OptionW    W

   

4

Area OptionW   W

  40W

Option 1W

                      17

Option 2W

                      40

..

MODEL : XXXXXX     Module : XXXX
S/W Ver. : X.XX          ROM : XXXXXXX
UTT                X           Temp : xxxxx : Celsius
ADC CAL.
RGB :WW

    OK  

Component SDW

    OK 

Component HDW

    OK 

EDID    RGB(OK)  HDMI1(OK)  HDMI2(OK)  HDMI3(OK)

Tool OptionW    W

   

4

Area OptionW   W

  40W

Option 1W

                      17

Option 2W

                      40

( Fig. 3)

Model 

Tool option 

Model 

Tool option

Model 

Tool option 

42PQ20R 

42PQ70BR

7 

42PQ600R 

13 

50PQ20R 

50PQ70BR

8 

50PQ600R 

14 

42PQ30R-TA 

42PQ200R

9 

50PS80BR 

19 

50PQ30R-TA

50PQ200R

10 

60PS80BR 

20 

42PQ60R 

42PQ300R

11 

50PS60FR 

21 

50PQ60R 

50PQ300R

12 

42PQ30R-MA 

22 

50PQ30R-MA 

42PQ10R 

50PQ10R 

25 

24 

2 

1

3 

 

4 

5 

6 

23 

O

WXGA EDID DATA(50inch)

<Analog(RGB) : 128bytes>

<HDMI 1 : 256bytes>

<HDMI 2 : 256bytes>

<HDMI 3 : 256bytes>
SIDE HDMI(HDMI 3) is adjusted above 60 Tool model

O

XGA EDID DATA(42inch)

<Analog(RGB) : 128bytes>

<HDMI 1 : 256bytes>

<HDMI 2 : 256bytes>

<HDMI 3 : 256bytes> 
SIDE HDMI(HDMI 3) is adjusted above 60Tool model

- 10 -

O

FHD EDID DATA (50/60inch–PQ70BR, PS60FR, PS80BR Tool )

<Analog(RGB): 128bytes>

< HDMI 1 : 256bytes>

< HDMI 2 : 256bytes>

<HDMI 3 : 256Bytes> SIDE HDMI(HDMI 3)

HDCP download process is deleted in H6 models
In H6 models, it is usimg the EEPROM masking HDCP Key

- Do not connect external input cable
- Adjustment result is applied to SET On/Off later.

*  Adjustment  is  done  using  internal  ADC,  so  input  signal  is  not

necessary.

(1) Convert to Component1 input source.
(2) Press ADJ key on R/C for adjustment.
(3) Enter Password number. The value of Password is “0 0 0

0”.

(4) Select “0. ADC calibration” by using 

D

/

E

(CH +/-) and press

ENTER(

V

).

(5)  Start  ADC  adjustment  by  using 

F

/

G

(VOL  +/-)  or  press

ENTER(

V

).

(6) ADC adjustment is executed automatically .

When ADC adjustment is finished, this OSD appear.

(PP91C/D Not Support)

Auto RGB Gain/Offset Adjustment

(1) Convert to PC in Input-source
(2) Press ADJ key on R/C for adjustment.
(3) Enter Password number. The value of Password is “0 0 0

0”.

(4) Select “0. ADC calibration” by using 

D

/

E

(CH +/-) and press

ENTER(

V

).

(5)  Start  ADC  adjustment  by  using 

F

/

G

(VOL  +/-)  or  press

ENTER(

V

).

(6) ADC adjustment is executed automatically .

When ADC adjustment is finished, this OSD appear.

Notice : After All mode check, set the Speaker Volume “0”.

(Only for PP91C/D)

(1) Convert to RF input source.
(2) Press ADJ key on R/C for adjustment.
(3) Enter Password number. The value of Password is “0 0 0

0”.

(4) Select “0. ADC calibration” by using 

D

/

E

(CH +/-) and press

ENTER(

V

).

(5)  Start  ADC  adjustment  by  using 

F

/

G

(VOL  +/-)  or  press

ENTER(

V

).

(6) ADC adjustment is executed automatically .

When ADC adjustment is finished, this OSD appear

- 11 -

RF input

NO SIGNAL or White noise

AV / Component / RGB input

NO SIGNAL

Notice : After All mode check, set the Speaker Volume “0”.
Caution : Don’t Press the Power Key on Remote Controller.
Just AC Power Off. ( Not DC off )
Notice : From this sentence, All working is mass production.

(Vs voltage Adjustment)

D.M.M 1EA

Refer to (Fig. 4)

1)  Connect  +  terminal  of  D.  M..M.  to  Vs  pin  of  P702,

connect -terminal to GND pin of P702.

2)  After  turning  VR901,  voltage  of  D.M.M  adjustment  as

same as Vs voltage which on label of panel right/top  (
deviation ; ±0.5V)

(1)  Purpose:  Adjust  the  color  temperature  to  reduce  the

deviation of the module color temperature.

(2)  Principle  :  To  adjust  the  white  balance  without  the

saturation,  Fix  the  one  of  R/G/B  gain  to  C0  and  decrease
the others.

(3) Adjustment mode: Two modes of Cool, Warm and Medium

(1) Remote controller for adjustment 
(2) Color Analyzer : CA-100+ or CA-210 or same product

- PLASMA TV(ch : 10)

(3) Auto W/B adjustment instrument(only for Auto adjustment)

- Do the white balance adjustment under the 10LUX

[ Notice:  When  using  the  Color  Analyzer  with  PDP,

recommend the CA-100 more than CA-210.
If CA-100 can not available, it is also good to use the CA-210.

(4) PC (for communication through RGB) 
(5) Pattern Generator (MSPG-925FA etc.)

-Before  white  balance,  press  the  ADJ  key  and  select  third

row like (Fig. 5)

-To enter White-balance mode, Enter Password Number “0

0 0 0” and  select third row. 

[ Caution: System control Host should be “DDC” for adjustment.

(6) Adjust W/B DATA, for all CSM, choose ‘COPY ALL’

(For Automatic Adjustment) 

(Method 2, using RS-232C, You connect RS-232C Cable)

- 12 -

(Fig. 4)

EZ ADJUST

0. ADC CALIBRATION  : TV

1. ADC ADJUST
2. SUB B/C ADJUST

3. W/B ADJUST

4. WHITE PATTERN   : OFF
5. EDID D/L

(Fig. 5)

3. W/B ADJUST

ModeWWW

: TV

TEMPERATUREWW

: Medium

R-Gain.WWW

: 192

G-Gain.WWW

: 192

B-Gain.WWW

: 192

R-OffsetWWW

: 128

G-OffsetWWW

: 128

B-OffsetWWW

: 128

COPY ALL

(Fig. 6)

Method 2-(RS-232C)