DOWNLOAD LG 50PQ100R-ZA (CHASSIS:PP91A) Service Manual ↓ Size: 9.62 MB | Pages: 68 in PDF or view online for FREE

- 5 -

V

(1) 42” XGA 

(2) 50” WXGA

(3) 50” FHD

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No

Item

Specification

Remark

50 inch 16:9 Color plasma Display Module

16:9

PDP50G2####,

RGB Closed(Well) Type 

1) Temp.

: 0 ~ 55deg

2) Humidity : 20 ~ 80%

3) Temp. : -10 ~ 60deg

4) Humidity : 10 ~ 90%

AC100-240V~, 50/60Hz

PDP

Glass Filter

LGE SPEC.

Maker: LGIT

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No

Item

Specification

Remark

50 inch 16:9 Color plasma Display Module

16:9

PDP50H3####,

RGB Closed Type 

1) Temp.

: 0 ~ 55deg

2) Humidity : 20 ~ 80%

3) Temp. : -10 ~ 60deg

4) Humidity : 10 ~ 90%

AC100-240V~, 50/60Hz

PDP

Glass Filter

LGE SPEC.

Maker: LGIT

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No

Item

Specification

Remark

42 inch 16:9 Color plasma Display Module

16:9

PDP42G2####,

RGB Closed Type 

1) Temp.

: 0 ~ 60deg

2) Humidity : 20 ~ 80%

3) Temp. : -20 ~ 60deg

4) Humidity : 10 ~ 90%

AC100-240V~, 50/60Hz

PDP

Glass Filter

LGE SPEC.

Maker: LGIT

- 6 -

V

(1) EU Spec.(ZA)

(2) NON-EU Spec.(TA)

 

 

 

 

 

 

 

- 7 -

This spec sheet is applied to all of the PP91A/B/C/D chassis. 

(1) Because this is not a hot chassis, it is not necessary to use

an  isolation  transformer.  However,  the  use  of  isolation
transformer will help protect test instrument.

(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of

25±5°C  of  temperature  and  65±10%  of  relative  humidity  if
there is no specific designation.

(4)  The  input  voltage  of  the  receiver  must  keep  100~240V,

50/60Hz.

(5) The receiver must be operated for about 5 minutes prior to

the adjustment when module is in the circumstance of over
15°
- In case of keeping module is in the circumstance of 0°C,

it should be placed in the circumstance of above 15°C for
2 hours

- In case of keeping module is in the circumstance of below

-20°C,  it  should  be  placed  in  the  circumstance  of  above
15°C for 3 hours,.

This  is  for  downloading  the  s/w  to  the  flash  memory  of  the
IC603

(1) PC
(2) ISP_tool program
(3) Download jig

(1) IC name and circuit number : Flash Memory and IC603
(2) Use voltage : 3.3V (5 pin)
(3) SCL : 15 pin
(4) SDA : 12 pin
(5) Tact time : about 2min and 30seconds

(PP91C/D Not support)

1) Connect the download jig to D-sub jack

2) Connect the PC to USB jack

1) Execute ‘ISP Tool’ program in PC, then a main window will

be opened

Double click

2) Click the connect button and confirm “Dialog Box”.

3) Click the Config button and Change speed

E2PROM Device setting : over the 350Khz

4) Read and write bin file

Click “(1)Read” tab, and then load download file(XXXX.bin)
by clicking “Read”.

5) Click “Auto(2)” tab and set as below
6) Click “Run(3)”.
7) After downloading, check “OK(4)” message. 

[Caution]
- Using ‘power on’ button of the control R/C, power on TV.
-  USB  file  (EPK)  version  must  be  bigger  than  downloaded

version of main B/D.

(1) Using ‘Power ON’ button of the control R/C, Power on TV.
(2) Insert the USB memory stick to the SET.
(3)  Display  USB  loding  message  then,  push  the  ‘Exit’  Key  of

control R/C

(4)  Push  the  ‘MENU’  Key  and  move  the  cusor  ‘OPTION’  of

OSD ( Fig. 1)
*  Caution:  Don’t  push  the  ‘OK’  key.Just  cusor  is  on  the

‘OPTION’ menu.

(5) Push the “7” key of control R/C continuously.

Then, Display “TV Software Update” Pop-up menu. (Fig. 2)

- 8 -

( Fig. 1)

( Fig. 2)