LG 50PM6700-TK (CHASSIS:PA22A) Service Manual ▷ View online
- 7 -
3.4. EDID
(The Extended Display Identification Data)
■ RGB [C/S: B1]For FHD Models
EDID Block 0, Bytes 0-127 [00H-7FH]
Block Type: EDID 1.3
■ HDMI [C/S: 9804] :For FHD Models
Block Type: EDID 1.3
EDID Block 1, Bytes 128-255 [80H-FFH]
Block Type: CEA EDID Timing Extension Version 3
* CheckSum & Physical Address Table.
- Each HDMI Input has their own physical address(on
Address:9E). So, each HDMI Input has different C/S
value.
■ HDMI INPUT Physical Address Table
■ HDMI INPUT C/S Table.
- FHD
4. SET assembly adjustment method
* Caution: Each PCB assembly must be checked by check
JIG set. (Because power PCB Assembly damages
to PDP Module, especially be careful)
4.1. POWER PCB Assembly Voltage adjustment
(Va, Vs voltage adjustment)
Test equipment : D.M.M 1EA
Connection Diagram for Measuring : refer to fig.4
Adjustment method
4.1.1. Va adjustment
(1) Connect + terminal of D. M.M. to Va pin of P811, connect
-terminal to GND pin of P811.
(2) After turning VR502,voltage of D.M.M adjustment as same
as Va voltage which on label of panel right/top (deviation;
±0.5V)
4.1.2. Vs adjustment
(1) Connect + terminal of D. M..M. to Vs pin of P811, connect
-terminal to GND pin of P811.
(2) After turning VR901, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top (
deviation ; ±0.5V)
4.2. Adjustment of White Balance
- Required Equipment
● Remote controller for adjustment
● Color Analyzer ( CS-1000, CA-210 or same product
: CH 10 (PDP)
* Please adjust CA-210 by CS-1000 before measuring
● Auto W/B adjustment instrument(only for Auto
adjustment)
● 9 Pin D-Sub Jack(RS232C) is connected to the AUTO
W/B EQUIPMENT
Before Adjust of White Balance, Please press
POWER ONLY key
- Adjust Process will start by execute RS232C Command.
● Color temperature standards according to CSM and Module
● CS-1000/CA-100+/CA-210(CH 10) White balance adjust-
ment coordinates and color temperature.
Address
HDMI1
HDMI2
HDMI3
HDMI4
9E
10
20
30
40
HDMI1
HDMI2
HDMI3
HDMI4
CheckSum
9804
98F4
98E4
98D4
CSM
PLASMA
Cool
11000K
Medium
9300K
Warm
6500K
CSM
Color Coordination
Temp
± Color
Coordination
x
y
COOL
0.276
0.283
11000K
0.002
MEDIUM
0.285
0.293
9300K
0.002
WARM
0.313
0.329
6500K
0.002
- 8 -
* Manual W/B process (using adjusts Remote control)
- Please Adjust in AV 1 MODE, Turn off Energy Saving Mode.
1) Enter ‘PICTURE RESET’ on Picture Mode, and then
turn off Fresh Contrast and Fresh colour in Advanced
Control
2) After enter Service Mode by pushing “ADJ” key,
3) Enter White Pattern off of service mode, and change off
-> on.
4) Enter “W/B ADJUST” by pushing “►” key at “3. W/B
ADJUST”.
* Gain Max Value is 192. So, Never make any Gain Value
over 192 and please fix one Value on 192, between R, G
and B.
* Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (Illumination is less than 10ux).
(2) Measure and adjust after sticking the Color Analyzer (CA-
100+, CA210) to the side of the module.
(3) Aging time
- After aging start, keep the Power on (no suspension of
power supply) and heat-run over 5 minutes
* Auto adjustment Map (RS232C)
4.3. Serial number download & Model name D/L.
(1) Press "Power on" button of a service R/C.(Baud rate :
115200 bps)
(2) Connect RS232-C Signal Cable and start ‘Option Check
Program Ver3.8’
(3) Scan serial Number and press ‘F5’ button.
(4) Check ‘OK’ on program 1) program.
(5) Press ‘In start’ button on SVC R/C, check Serial Number
and Model Name.
4.4. Check Tool Option and write Country
Group & Area Code(Option) D/L
- Refer to Table 3.4 insert tool option.
No
Index
CMD1
CMD2
Set ID
Data
1
Start
w
b
0
00
2
Gain Start
w
b
0
10
3
Gain End
w
b
0
1F
4
Offset Start
w
b
0
20
5
Offset End
w
b
0
2F
6
End
w
b
0
FF
7
Medium R
j
a
0
00~FF
8
Medium G
j
b
0
00~FF
9
Medium B
j
c
0
00~FF
10
Warm R
j
d
0
00~FF
11
Warm G
j
e
0
00~FF
12
Warm B
j
f
0
00~FF
13
Cool R
j
g
0
00~FF
14
Cool G
j
h
0
00~FF
15
Cool B
j
i
0
00~FF
16
Cool R,G,B
j
j
0
00~FF
17
Medium
j
k
0
00~FF
18
Warm
j
l
0
00~FF
Min
Typ
Max
R-GAIN
0
192
192
G-GAIN
0
192
192
B-GAIN
0
192
192
Country Group
Market
Area Option
AJ
Myanmar
Etc.
257
Australia, New Zealand
Singapore, Malaysia
263
Indonesia
262
Vietnam
261
Thailand
16647
Sri Lanka
17671
India
18183
JA
Irap, Lybia, Yemen,
Syria, Sudan, West Afria
Ect.
257
Tunisia, Kuwait, Oman,
Kenya, Uganda
Palestine(SBITANY)
259
Qatar
Nigeria
260
U.A.E
Saudi Arabia
Barhrain
261
Egypt, Iran, Jordan
Lebanon
263
Pakistan
16642
IL
Israel(H.Y.E)
259
- 9 -
4.5. Checking the EYE-Q Operation.
(1) Press the EYE Key on the adjustment remote controller.
(2) Check the Sensor DATA ( It must be under 10) and keep
the data longer than 1.5s
(3) Check ‘OK’
(Sensor DATA 0 ~ 4095, Power Saving Mode 0 ~ 12)
* IF you press IN-STAP Button, change Green Eye-check
OSD.
4.6. PING TEST
* In this case Network setting is on Manual Setting.
Connect : SET->LAN Port == PC->LAN Port
4.6.1. Equipment Setting
(1) Play the LAN Port Test PROGRAM.
(2) Input IP set up for an inspection to Test
* IP Number : 12.12.2.2
4.6.2. LAN PORT inspection (PING TEST)
* In this case Network setting is on Manual Setting.
(1) Play the LAN Port Test Program.
(2) connect each other LAN Port Jack.
(3) Play Test (F9) button and confirm OK Message.
(4) remove LAN CABLE
4.7. Magic Motion Remote Controller test
(1) Equipment: RF R/C for test,
(2) You must confirm the battery power of RF-R/C before test
(Recommend that change the battery per every lot)
(3) Sequence (test)
1) if you select the ‘start key(Wheel Key)’ on the controller,
you can pairing with the TV SET.
2) You can check the cursor on the TV Screen, when select
the ‘Wheel Key’ on the controller
3) You must remove the pairing with the TV Set by select
‘Mute Key’ on the controller.
4.8. Wi-Fi Test(Except for PM47*)
Step 1) Turn on TV
Step 2) Select ‘Network Connection’ option in Network Menu.
Step 3) Select ‘Start Connection’ Button in ‘Network
Connection’.
Step 4) If the system finds any AP like blow PIC, it is working
well.
Green Eye-Check(Factory Mode)
Sensor Data
9
Power saving mode
1
OK
- 10 -
4.9. 3D function test
- Required Equipment
● Pattern Generator :
MSHG-600, MSPG-6100 [SUPPORT HDMI1.4])
MODE : HDMI mode NO. 872
Pattern No.83
(1) Please input 3D test pattern like below (HDMI mode NO.
872 , pattern No.83)
(2) When 3D OSD appear automatically, then press OK button
on ADJ Remote Controller.
(3) Check the picture. The picture must be same as below.
(Don’t have to wear 3D glasses.)
5. Set Information
(Serial No & Model name)
5.1. Check the serial number & Model Name
(1) Push the menu button and press red button on R/C to
enter ‘Customer Support’menu.
(2) Move to ‘signal test’ menu. And check Serial No & Model
Name Select the STATION -> Diagnostics -> To set
6. SW Download Guide.
* Before put a *.epk to USB Stick make ‘LG_DTV’ folder in
USB. Then, put *.epk file to ‘LG_DTV’ folder and Turn on TV
(1) Put the USB Stick to the USB socket
(2) Automatically detecting update file in USB Stick
* If your downloaded program version in USB Stick is Low,
it didn’t work.
But your downloaded version is High, USB data is
automatically detecting.
(3) Show the message “Copying files from memory”
(4) Updating is staring.
(5) Updating Completed, The TV will restart automatically.
After turn on TV, Please press ‘IN-STOP’ button on ADJ
Remote-control.
* IF you don’t have ADJ R/C, enter ‘Factory Reset’ in
OPTION MENU.
(6) When TV turns on, check the Updated version on Product/
Service Info. MENU.
Click on the first or last page to see other 50PM6700-TK (CHASSIS:PA22A) service manuals if exist.