DOWNLOAD LG 42PX5D-UB (CHASSIS:AF-05FB) Service Manual ↓ Size: 20.23 MB | Pages: 41 in PDF or view online for FREE

These instructions are applied to all of the PDP TV, AF-05FB.

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help protect test equipment.

(2) Adjustments must be done in the correct order.
(3) The adjustments must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.

(4) The input voltage of the receiver be must kept 110V, 60Hz

when adjusting.

(5) The receiver must be operational for about 15 minutes

prior to the adjustments.  

1) After receiving 100% white pattern, the receiver must be

operated prior to adjustment. (Or 7. White Pattern
condition in EZ - Adjust)

2) Enter into White Pattern 

- Press POWER ON Key on the Service Remote

Control (S R/C)

- Enter the Ez - Adjust by pressing ADJ Key on the

Service Remote Control (S R/C).

- Select the 7. White Pattern using CH +/- Key and

press the Enter(

Y

) Key. 

Display the 100% Full White Pattern. 

[

Set is activated HEAT-RUN without signal generator in

this mode.

If you turn on a still screen more than 20 minutes (Especially
Digital pattern(13 CH), Cross Hatch Pattern), an afterimage
may occur in the black level part of the screen.

(1) Test Equipment: PC, Jig for download
(2) Connect the power of VSC B/D.
(3) Execute download program(iMPACK) of PC.
(4) After executing the hot key on the Programmer, click icon
(5) End after confirming

(1) As shown below, connect the MPLAB ICD2 equipment, PC

and Digital Connector.

(2) Turn on the MPLAB ICD2 POWER Supply.
(3) After turn on the PC and MONITOR, select the ‘MPLAB

IDE’ from the screen.

(1) When the program is executed, select the MPLAB ICD2

from Programmer -> Select Programmer . 

(2) Select "Configure -> Select Device".

(3) When the "Select Device" window appears, select the

PIC18F1220 from "Device" and press OK.

- 9 -

PC

VSC

B/D

<Fig 1>  Connection Diagram of EPLD Download

+13V

<Digital Board>

Connect the MPLAB ICD2 and connector of Digital Board

Connect the RS-232 or USB Cable

GND
Data

- 10 -

(4) Select "Programmer -> Connect".

When connected with the Micom, the display message on
the Output window appears as below. 

(5) Select "File -> Import", select the Work HEX file and open.

(6) Select "Programmer -> Program".

(7) Download is executed and about 5 seconds later, the

"Programming succeeded" message is displayed on the
Output window and the Download process is ended. 

(8) The execution of process (6) is convenient when using the

short-cut icon. 

(1) As shown below, connect the MPLAB ICD2 equipment, PC

and Digital Connector.

(2) Turn on the MPLAB ICD2 POWER Supply.
(3) After turn on the PC and MONITOR, select the ‘MPLAB

IDE’ from the screen.

(1) When the program is executed, select the MPLAB ICD2

from "Programmer -> Select Programmer" . 

(2) Select "Configure -> Select Device".

+13V

+5V

GND
Data
Clock

<Digital Board>

Connect the MPLAB ICD2 and connector of Digital Board

Connect the RS-232 or USB Cable

Connecting to MPLAB ICD 2

...Connected

Setting Vdd source to MPLAB ICD 2

Target Device PIC18F1220 found, revision = 0x4 

...Reading ICD Product ID

Running ICD Self Test

...Passed

MPLAB ICD 2 Ready

- 11 -

(3) When the "Select Device" window appears, select the

PIC18F242 from "Device" and press OK.

(4) Select "Programmer -> Connect".

When connect with the Micom, the display message on the
Output window appears as below. 

(5) Select "File -> Import", select the Work HEX file and open.

(6) Select "Programmer -> Program".

(7) Download is executed and about 3 seconds later, the

"Programming succeeded" message is displayed on the
Output window and the Download process is ended. 

(8) The execution of process (6) is convenient when using the

short-cut icon. 

(1) Connect the MEMORY JIG and PC.
(2) Turn on the JIG MAIN POWER SWITCH.
(3) After turn on the PC and MONITOR, execute the

‘Certificate Downloader v1.4’  from the screen.

(1) After open the ‘Certificate Downloader v1.4’, enter

Connection set and set the as same below.
The port settings are determined by each PC's setup.

Connecting to MPLAB ICD 2

...Connected

Setting Vdd source to MPLAB ICD 2

Target Device PIC18F242 found, revision = 0x7 

...Reading ICD Product ID

Running ICD Self Test

...Passed

MPLAB ICD 2 Ready

- 12 -

(2) Select ‘Connection’ and SET connected to RS-232C. 
(3) After clicking "Enter", confirm that "Enter Password:"

appears. 

(4) Click the "OpenFile - Download" button from CP Data

Download, ‘select the Private Key’ appears and click
ENTER.  

(5) After clicking ENTER, the ‘opens Private key' window

appears and select the Private key applied to the SET.
The Private Key file name is on the Label of the Digital
Board.

(6) When the Dialog window appears, click OK and the write

work will begin.

(7) When completed, click ‘CP Data Download: OK’ 

[

When ‘CP Data Download: OK’ does not appear, certificate

has not Download correctly.
SET is rebooted and certificate Download work must be
repeated.  

(8) Now, you may begin IEEE1394 (DTCP) Download work.

Select the “DTCP.dat” file by pressing the ‘DTCP File
Open’ button.