LG 42PC5D-UC / 42PC5DC-UC (CHASSIS:PA-73E) Service Manual ▷ View online
- 13 -
ADJUSTMENT INSTRUCTIONS
5-5. Adjustment(LG IT: EAY32957901)
(1) Va Adjustment
1) Connect + terminal of D.M.M to Va pin of P812 and
connect – terminal to GND pin of P812.
2) Adjust VR951 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P812 and
connect – terminal to GND pin of P812.
2) Adjust VR901 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
6. ADC-Set Adjustment
6-1. Synopsis
ADC-Set adjustment to set the black level and the Gain to
optimum.
optimum.
6-2. Test Equipment
Service R/C, 801GF(802V, 802F, 802R) or MSPG925FA
Pattern Generator
(480i/1080i The Horizontal 100% Color Bar Pattern adjust to
within 0.7±0.1Vp-p)
Pattern Generator
(480i/1080i The Horizontal 100% Color Bar Pattern adjust to
within 0.7±0.1Vp-p)
[ADC adjustment (MSPG-925Fx series) Model No. & Pattern No.]
- Model No.: #209(480i adjustment), #223(1080i adjustment)
- Pattern No.: #65(7ColorBar Pattern)
- Model No.: #209(480i adjustment), #223(1080i adjustment)
- Pattern No.: #65(7ColorBar Pattern)
<Fig. 1-4> 50” PSU(LG IT: EAY32957901)
<Fig. 2> Adjustment Mode
<Fig. 3> Adjustment Pattern: 480i/1080i 60Hz HozTV31Bar
Pattern
- 14 -
ADJUSTMENT INSTRUCTIONS
6-3. Adjustment
(1) Select Component1 as the input with 100% Horizontal
Color Bar Pattern(HozTV31Bar) in 480i Mode
(2) After receiving signal for at least 1 second, press the ADJ
Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘2. ADC 480i Comp1’.
Pressing the Enter Key to adjust automatically.
the ‘2. ADC 480i Comp1’.
Pressing the Enter Key to adjust automatically.
(3) When the adjustment is over, 'MST3361 Component
Success’ is displayed. If the adjustment has errors,
'MST3361 Configuration Error’ is displayed.
'MST3361 Configuration Error’ is displayed.
(4) Select Component1 as the input with 100% Horizontal
Color Bar Pattern(HozTV31Bar) in 1080i Mode.
(5) After receiving signal for at least 1 second, press the ADJ
Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘3. ADC 1080i Comp1/RGB’.
Pressing the Enter Key to adjust automatically.
the ‘3. ADC 1080i Comp1/RGB’.
Pressing the Enter Key to adjust automatically.
(6) When the adjustment is over, 'MST3361 Component
Success’ is displayed. If the adjustment has errors,
'MST3361 Configuration Error’ is displayed.
'MST3361 Configuration Error’ is displayed.
(7) After the Component MST3361 adjustment is over, convert
the RGB-DTV Mode and display Pattern.
When the adjustment is over, 'MST3361 RGB_DTV
Success’ is displayed.
When the adjustment is over, 'MST3361 RGB_DTV
Success’ is displayed.
(8) Readjust after confirming the case Pattern or adjustment
condition where the adjustment errors.
(9) After adjustment is complete, exit the adjustment mode by
pressing the ADJ KEY.
7. EDID(The Extended Display
Identification Data)/DDC
(Display Data Channel) Download
(Display Data Channel) Download
This is the function that enables “Plug and Play".
7-1. HDMI EDID Data Input
(1) Required Test Equipment
1) PC, Jig for adjusting DDC. (PC serial to D-sub
Connection equipment)
2) S/W for writing DDC(EDID data write & read)
3) D-Sub cable
4) Jig for HDMI Cable connection
3) D-Sub cable
4) Jig for HDMI Cable connection
(2) Preparation for Adjustments &
Setting of Device
1) Set devices as below and turn on the PC and JIG.
2) Open S/W for writing DDC (EDID data write & read).
2) Open S/W for writing DDC (EDID data write & read).
(operated in DOS mode)
7-2. EDID DATA for PA-73E
[42PC5D-UC]
:
EDID for HDMI-1 (DDC (Display Data Channel) Data)
EDID Block 0 table =
EDID Block 0 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
__________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 02 20 00 00 00 FC
70 | 00 34 32 50 43 35 44 2D 55 43 0A 20 20 20 01 5D
EDID Block 1 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
__________________________________________________
0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 10 00 01 1D 00 72 51 D0 1E 20 6E 28 55
20 | 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20 58
30 | 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0 2D
40 | 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A 20
50 | E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A7
:
EDID for HDMI-2 (DDC (Display Data Channel) Data)
EDID Block 0 table =
EDID Block 0 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
__________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28
40 | 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20
50 | 58 2C 25 00 C4 8E 21 00 00 9E 00 00 00 FC 00 34
60 | 32 50 43 35 44 2D 55 43 0A 20 20 20 00 00 00 FD
70 | 00 38 4B 1F 3C 09 00 0A 20 20 20 20 20 20 01 0D
EDID Block 1 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
__________________________________________________
0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 20 00 8C 0A D0 8A 20 E0 2D 10 10 3E 96
20 | 00 C4 8E 21 00 00 18 8C 0A D0 8A 20 E0 2D 10 10
30 | 3E 96 00 13 8E 21 00 00 18 00 00 00 00 00 00 00
40 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 35
PDP TV SET
(or Digital Board)
- 15 -
ADJUSTMENT INSTRUCTIONS
:
EDID for RGB-PC
EDID Block 0 table =
EDID Block 0 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
___________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 68 73 41 96 0A CF 30 A3 57 4C B0 23
20 | 09 50 4E A1 08 00 01 01 01 01 01 01 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 34 32 50 43 35 44 2D 55 43 0A 20 20 20 00 77
[50PC5D-UC]
:
EDID for HDMI-1 (DDC (Display Data Channel) Data)
EDID Block 0 table =
EDID Block 0 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
___________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 02 20 00 00 00 FC
70 | 00 35 30 50 43 35 44 2D 55 43 0A 20 20 20 01 5E
EDID Block 1 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
____________________________________________________
0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 10 00 01 1D 00 72 51 D0 1E 20 6E 28 55
20 | 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20 58
30 | 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0 2D
40 | 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A 20
50 | E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A7
:
EDID for HDMI-2 (DDC (Display Data Channel) Data)
EDID Block 0 table =
EDID Block 0 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
___________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28
40 | 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20
50 | 58 2C 25 00 C4 8E 21 00 00 9E 00 00 00 FC 00 35
60 | 30 50 43 35 44 2D 55 43 0A 20 20 20 00 00 00 FD
70 | 00 38 4B 1F 3C 09 00 0A 20 20 20 20 20 20 01 0E
EDID Block 1 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
____________________________________________________
0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 20 00 8C 0A D0 8A 20 E0 2D 10 10 3E 96
20 | 00 C4 8E 21 00 00 18 8C 0A D0 8A 20 E0 2D 10 10
30 | 3E 96 00 13 8E 21 00 00 18 00 00 00 00 00 00 00
40 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 35
:
EDID for RGB-PC
EDID Block 0 table =
EDID Block 0 table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
___________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 68 73 41 96 0A CF 30 A3 57 4C B0 23
20 | 09 50 4E A1 08 00 01 01 01 01 01 01 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 35 30 50 43 33 44 2D 55 45 0A 20 20 20 00 78
- 16 -
ADJUSTMENT INSTRUCTIONS
8. Adjustment of White Balance
8-1. The Purpose and Principal of Color
Temperature Adjustment
(1) Purpose: to reduce the difference in color temperature
among modules
(2) Principal: A module is in full dynamic range when RGB
Gain on OSD is 192. To adjust the white balance without
causing full dynamic range and full data, fix one of RGB
Gains at 192 and control the other two by reducing them
from 192.
causing full dynamic range and full data, fix one of RGB
Gains at 192 and control the other two by reducing them
from 192.
8-2. Required Equipment
(1) Color Analyzer : CA-100+(CH 10), CA-100(CH 10) or CA-
210(CH 10)
=> To adjust color temperature of Plasma, CS-1000 is the
=> To adjust color temperature of Plasma, CS-1000 is the
Color Analyzer and should be set to use CH 10 in which
white, red, green, and blue color are corrected. Conduct
the adjustment according to the coordinates for White
Balance adjustment in the table below.
white, red, green, and blue color are corrected. Conduct
the adjustment according to the coordinates for White
Balance adjustment in the table below.
In the case of using color-corrected CA-100, CA-100+,
and CA-210 (using CH10) to adjust Plasma, there are
differences for CS-1000 in the result due to the
characteristics of a module or filter. The target values of
the color coordinates in the table below are given to
prevent it.
and CA-210 (using CH10) to adjust Plasma, there are
differences for CS-1000 in the result due to the
characteristics of a module or filter. The target values of
the color coordinates in the table below are given to
prevent it.
(2) Automatic adjustor (with automatic adjustment necessity
and the RS-232C communication being possible)
8-3. Connection Diagram of Equipment
for Measuring
(Automatic Adjustment)
Use the internal pattern to adjust White Balance. The pattern
is automatically given when the automatic adjustment device
is connected or when a user presses ADJ on the remote
controller to start Ez Adjust and then selects 6.White-Balance.
is automatically given when the automatic adjustment device
is connected or when a user presses ADJ on the remote
controller to start Ez Adjust and then selects 6.White-Balance.
[
Requirements for Automatic Adjustment
(1) The illuminance of surroundings
10 lux or less; preventing light in surroundings as much as
possible
possible
(2) The location of the Probe
1) For PDP: place the color analyzer (CA-100, CA-100+,
and CA-210) close to the surface of a module and start
the adjustment.
the adjustment.
2) For LCD: place the color analyzer (CA-210) close to the
surface of a module within 10 cm and keep the probe of
the color analyzer at 80° to 100° angle from the surface
of a module.
the color analyzer at 80° to 100° angle from the surface
of a module.
(3) Aging time
1) Once Aging is started, keep the power on without power
supply interruption for at least 15 minutes for heat run.
2) For PDP, use the internal pattern to adjust White
Pattern.
3) For LCD, use NO SIGNAL or Full White Pattern to
ensure the backlight is turned on.
8-4. Adjustment of White Balance
(Automatic Adjustment)
(1) Turn on the POWER ON(
Â
) of the remote controller to set
the adjustment and then start the automatic adjustment or
set the Baud Rate to 115200.Â) of the remote controller to
set the Baud Rate to 115200.Â) of the remote controller to
(2) Start the adjustment from “wb 00 00” and complete it at
“wb 00 ff”. (Adjust the offset if necessary)
wb 00 00 the automatic adjustment of White Balance is
started.
wb 00 10 adjusting gain (internal pattern appears) is
started.
ja 00 ff adjusting data
jb 00 c0
...
wb 00 1f adjusting gain is completed.
Adjust the offset (from wb 00 20 to wb 00 2f) if necessary.
wb 00 ff the automatic adjustment of White Balance
(internal pattern disappears) is completed.
started.
wb 00 10 adjusting gain (internal pattern appears) is
started.
ja 00 ff adjusting data
jb 00 c0
...
wb 00 1f adjusting gain is completed.
Adjust the offset (from wb 00 20 to wb 00 2f) if necessary.
wb 00 ff the automatic adjustment of White Balance
(internal pattern disappears) is completed.
C A -100+
C O L O R
A N A L Y Z E R
T Y P E ; C A -100+
F u l l W h i t e P at t er n
R S-232C
Connection Diagram of Automatic Adjustment
Click on the first or last page to see other 42PC5D-UC / 42PC5DC-UC (CHASSIS:PA-73E) service manuals if exist.