DOWNLOAD LG 42LG500H (CHASSIS:LA66A) Service Manual ↓ Size: 10.72 MB | Pages: 41 in PDF or view online for FREE

- 17 -

(1) Check Order 'Pass' Judgment

1) Connecting RJP Test JIG & RJP Port of Set with Modem

Cable(8Pin)

2) Check the RJP operation on OSD(In-start -> RJP Pin

Check -> 

G

3) 'SUCCESS! PIN CONNECTION OK' -> PASS
4) 'Pin Check Fail!!!!' -> NG
5) If the Result is 'NG', try One More

(2) Needs JIG & Equip. & Cable

1) RJP Check JIG, Modem Cable (8 Pin)

1) Push the ADJ key in an Adjust Remote controller.
2) Input the Option Number that was specified in the BOM,

into the Shipping area.

3) The work is finished, Push 

A

Key.

- 18 -

CURRENT PROBE : P6022A or same product

4.6 k‰ / 500 W

SC100

P203

P202

P401

400PF
3.15KV

400PF
3.15KV

P402

INPUT CONTROL SIGNAL

BURST DIMMING SIGNAL

INVERTER + POWER BOARD

VOLTAGE PROBE P6015A
or same product

VOLTAGE PROBE P6015A
or same product

INVERTER
CONNECTION
WIRE

INVERTER
TRANSFORMER

ON/OFF : 5V

SELECT
180Hz : 5V
150Hz : 0V

SYNC
180Hz, 3.3V, 50% Duty
150Hz, 3.3V, 50% Duty

INV_CTRL :5V

3.4V_ON : 5V

BURST_DIM
0-3.3V

A_DIM
0-1.65V

P201

AC INPUT

4.6 k‰ / 500 W

- 19 -

1) Does not  minute discharge at module. 
2) Non does not come into the front LED. 

Is plug in power cord?

Plug in power cord.

Yes

No

Is connect the Line Filter and

Power Board Cable?

Connect Cable.

Yes

No

Is Normal the Fuse(F100) on

Power Board?

Replace Fuse.

Yes

No

Is connect the Power Board and

13P cable of Main Board?

Connect Cable.

Yes

No

After remove the cable connect to Power Board(except the SC100
connection cable), authorizes the AC Voltage marking on manual.  When
ST-BY 5V does not operate, replace Power Board.

- 20 -

Does minute discharge

At Module?

Is the LVDS 

cable normal?

Is the IC1111 output

normal?

Check the LCD Module

Yes

No

YES

Yes

Reconnect the LVDS

cable in P600.

No

Is the IC506 (FLI8662)

Output normal?

Replace the main

board

No

Yes

Is the LED change when 

Push remote-control?

Replace the IR board

No

NO

Replace the 

Power board.

Is output the normality

Low/High voltage except

stand-by 5V?

NO

1) No OSD and image occur at screen.
2) It maintains the condition where the front LED is Blue

The screen does not become the display from specific input mode.

(RF, AV, Component, RGB, DVI).

- Check the all input mode should become normality display.
- Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode.

(Re-Check it Swap) 

Is normal the Tuner?

Is normal the

FIL8662?

Check the tuner cable.
* Isn’t cable has broken?
* Is the cable connected 
well from MPI card to tuner?

Cable inserts well.

Yes

No

No

Replace Tuner

No

Is normal the Input voltage, IIC
Communication and CVBS output?

Yes

Is normal the Input voltage, IIC
Communication and HV sync?

No

Replace IC or Main Board

No