DOWNLOAD LG 42LB5DC (CHASSIS:LA64A) Service Manual ↓ Size: 10.53 MB | Pages: 38 in PDF or view online for FREE

- 13 -

1) Select HCS12
2) Target Frequency Settings : 

A.  Checking  the  factor  ->  Use  Specified  Target

Frequency ..., Unsecure target...

B. Insert Target Bus Frequency -> 7372800

3) Specify Algorithm: 9S12dt128_128k .12P 
4) Specify S Record: select download file. 
5)  Checking  factor:  Erase  Device,  Blank  Check  Device,

Program Device, Verify Device 

* Notice!

Don't check other checking boxes. You must follow fig.
6)  Push  the  'Save  Image  to  Cyclone  PRO'  button,  files

transfer from PC to the Download JIG. 

5.1 Setting up like figure
(Setting: Press ADJ Key in the Adjust remocon.
Select  "System Control 3" by using  

D/E

(CH+/-) key, and press

V

(ENTER)

Using Adjust remocon, select module)

6.1 ADC adjustment on PCB Ass’y Level

1) Auto RF Color Balance.
2) Auto AV Color Balance.
3) Auto COMPONENT Balance.
4) Auto RGB Color Balance.

O 

ADC Calibration Protocol [ RS-232C]

* Baud Rate : 115,200bps
* RS232C Host : PC
* Echo : None

Processing programming..  Address  $0FFF80.  Done.

CMD> VM
Processing verifying... Done.

All Programming steps have been pre-processed.

Preparing CYCLONE PRO Flash....done.

Programming CYCLONE PRO Flash..  Address  $F0115B80

Running programming script...

Rushmore

Cortez Ver   :```

   1.05

D2A Ver       :``

   `    1.00

PTC Ver       :``

    1.00.001

Tool Option1```

         1

Tool Option2```

       73

Area Option```

         2

OPTION1```

         2

OPTION2```

         1

System Control1
System Control2

Power-off History
Panel Control
Fan Control
RJP Pin Check
Uart Control

System Control3

System Control3

System Control3

DAGC Setting

DAGC Setting
Decoder Setting

Decoder Setting
Turing Parameters

uring Parameters

Decoder Line Magin

Decoder Line Magin
Deburg Print

Deburg Print

MODULE``

MODULE``

  L42LPL

  L42LPL

MODULE OPTION``

MODULE OPTION``

SW

SW

PC -> Download Jig

Before ADC Calibration, should be executed the "Module type
selection".

MSPG-925

In-house

2CH

Model No:207

Pattern No:65

Model No:217

Pattern No:65

Model No:60

Pattern No:65

ADC Mode

ADC adjust

Input change

Data Read

End

Enter ADC Adjust mode

ADC adjust

Change input to AV1

Change input to COMP

Change input to RGB

ADC Parameter(Main)

ADC parameter(Sub)

Adjustment Confirmation

Escape ADC mode

NO

Item

Remark

CMD1 CMD2 Data 0

a

a

x

x

x

a

a

a

a

d

d

b

b

b

d

d

d

d

0

0

0

0

0

0

1

9

0

0

1

2

4

6

2

2

9

9

Change input to RF

Tune channel 2

Split display to DW

Change input to RF after

RGB adjustment

Escape DW mode

1.8Byte

(Input, resolution)

Check ADC in WB level

- 14 -

6.2 Auto AV (CVBS) Color Balance

6.1.1 Required Equipment
- Remote controller for adjustment 
- AV  Pattern  Generator:  802F  Pattern  Generator,  Master

(MSPG-925FS), etc

(Which  has  NTSC-J  Composite  Video  format  output  with
standard (1.0 Vpp) See Fig. 1)  

- It  is  very  import  to  use  correct  adjustment  pattern  like

Fig.1. 

6.1.2 Method of Auto AV (CVBS) Color Balance
1) Input  the  NTSC-J  Composite  Video  (Fig.1.)  into  video

input. 

=> MSPG-925FS Model No: 207 / Pattern No: 65 / NTSC-J
2) Set the EZ Picture to Daylight mode in Video menu.
3) Press INSTART key on R/C for adjustment.
4) Press  the 

G

(Vol.  +)  key  operate  to  set,  then  it  becomes

automatically.

5) Auto-RGB OK means completed adjustment.

* When adjust main picture, sub picture is included.

6.3 Auto Component Color Balance

6.2.1 Required Test Equipment
- Remote controller for adjustment
- 802F  Pattern  Generator  Which  has  720p  YPbPr  output

with Standard (0.7Vpp) See Fig. 2

- It  is  very  important  to  use  correct  adjustment  pattern  like

Fig. 2.

6.2.2 Method of Auto Component Color Balance
1) Input  the  Component  1280*720p  60Hz  signal  into

Component.

=> MSPG-925FS Model No: 217 / Pattern No: 65

2) Set the EZ Pictures to Daylight mode in Video menu.
3) Press INSTART key on R/C for adjustment. 
4) Press the 

G

(Vol. +) key operate To set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment

<Fig.2> Auto Component Color Balance Test Pattern

Default Value on OSD

<Fig.1> Auto AV (CVBS) Color Balance Test Pattern

Default Value on OSD

6.4 Auto RGB Color Balance

6.3.1 Required Test Equipment
- Remote controller for adjustment
- 802F Pattern Generator, Master (MSPG-925FS), etc.

(Which  has  XGA  60Hz  PC  Format  output  with  standard

(0.7Vpp) See  Fig. 3 )

-  It is very import to use correct adjustment pattern like Fig.

3.

6.3.2 Method of Auto RGB Color Balance
1) Input the PC 1024x768 @ 60Hz into RGB.

=> MSPG-925FS Model No: 60 / Pattern No: 65

2) Set the EZ Pictures to Daylight mode in Video menu.
3) Press INSTART key on R/C for adjustment. 
4) Press the 

G

(Vol. +) key  operate To set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

6.5 RF Color Balance

1) Input the RF cable(2 ch)
2) Set the EZ Pictures to Daylight mode in Video menu.
3) Press INSTART key on R/C for adjustment.  
4) Press the 

G

(Vol. +) key operate To set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment 

- 15 -

NM02

Default Value on OSD

<Fig.3> Auto RGB Color Balance Test Pattern

Default Value on OSD

7.1 EDID(The  Extended  Display  Identification  Data)  /

DDC(Display Data Channel) download

7.1.1 Required Test Equipment
1) Adjusting PC with S/W for writing EDID Data.
2) A Jig for EDID Download
3) Cable: Serial (9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable.

7.1.2 Setting of device

- When input HDMI EDID data through RGB or HDMI jack,

writing  8bits  of  the  data  at  every  turn  with  'DDC2B'
protocol.

7.1.3Data of EDID for 42LB5DC-UA

7.1.3.1 DDC data of Analog-RGB

7.1.3.2 DDC data of Digital-HDMI1

7.1.3.3 DDC data of Digital-HDMI2

8.1 Required Equipment

- Remote controller for adjustment 
- Color Analyzer (CA-210 or same product )
- Auto W/B adjustment instrument(only for Auto adjustment)
- Use inner(SELF) Pattern 

8.2 Adjustment of White Balance (For Manual adjustment)

Set TV input to RF.
Operate the zero-calibration of the CA-210, Ch.9. 
Then stick sensor to LCD module surface when you adjust. 
For  manual  adjustment,  it  is  also  possible  by  the  following
sequence.
1) Select white pattern of heat-run mode by pressing power

on  key  on  remote  control  for  adjustment  then  operate
heat run more than 15 minutes. 

2) Enter  the  White  Balance  adjustment  mode  by  pressing

the INSTART key twice (White Balance) on R/C.

3) Stick  sensor  to  center  of  the  screen  and  select  each

items using  

D/E

(CH +/-) key on R/C.

4) Adjust G Gain / B Gain using  

F/G

(VOL +/-) key on R/C.

5) Adjust it until color coordination becomes as below. 

- By controlling G, B GAIN, adjust X, Y target value. 
- R Gain fixed at cool, normal, warm mode.
- But, Control the R GAIN, unless it has correct value

(Initially, R/G/B gain and R/G/B offset values are fixed as below.)
Red Gain: 80h

Green Gain:  80h Blue Gain: 80h

Red Offset: 80h

Green Offset: 80h Blue Offset: 80h 

*Target value

6) When  adjustment  is  completed,  Exit  adjustment  mode

using EXIT key on R/C.

- 16 -

Before  adjustment  of  white  balance,  should  be  executed  the
'color balance adjustment'

<Fig.4> Connection Diagram of DDC download

x

y 

0.283±0.002

0.293±0.002

0.329±0.002

11000K

9300K

6500K

0.000

0.000

0.003

0.276±0.002

0.285±0.002

0.313±0.002

COOL

MEDIUM

WARM

Mode

Temp

uv