LG 32PG6000-ZA (CHASSIS:PD81A) Service Manual ▷ View online
(2) 42” XGA Module
(3) 50” FHD Module
(4) 60” FHD Module
- 5 -
Display Screen Device
Aspect Ratio
PDP Module
Operating Environment
Storage Environment
Input Voltage
1
2
3
4
5
6
No
Item
Specification
Remark
42 inch Wide Color Display Module
16:9
PDP42G1####,
RGB Closed(Well) Type, Glass Filter(38%)
Pixel Format : 1024 horiz. By 768 ver.
1) Temp. : 0 ~ 40 deg
2) Humidity : 20 ~ 80 %
3) Temp. : -20 ~ 60 deg
4) Humidity : 10 ~ 90 %
100-240V~, 50/60Hz
PDP
LGE SPEC.
Maker LG
Display Screen Device
Aspect Ratio
PDP Module
Operating Environment
Storage Environment
Input Voltage
1
2
3
4
5
6
No
Item
Specification
Remark
50 inch Wide Color Display Module
16:9
PDP50H2####,
RGB Closed(Well) Type, Glass Filter(38%)
Pixel Format : 1920 horiz. By 1080 ver.
1) Temp. : 0 ~ 40 deg
2) Humidity : 20 ~ 80 %
3) Temp. : -20 ~ 60 deg
4) Humidity : 10 ~ 90 %
100-240V~, 50/60Hz
PDP
LGE SPEC.
Maker LG
Display Screen Device
Aspect Ratio
PDP Module
Operating Environment
Storage Environment
Input Voltage
1
2
3
4
5
6
No
Item
Specification
Remark
60 inch Wide Color Display Module
16:9
PDP60H2####,
RGB Closed(Well) Type, Glass Filter(38%)
Pixel Format : 1920 horiz. By 1080 ver.
1) Temp. : 0 ~ 40 deg
2) Humidity : 20 ~ 80 %
3) Temp. : -20 ~ 60 deg
4) Humidity : 10 ~ 90 %
100-240V~, 50/60Hz
PDP
LGE SPEC.
Maker LG
- 6 -
V
Model General Specification
Market
Broadcasting system
Receiving system
Scart Jack(2EA)
Video Input (1EA)
S-Video Input (1EA)
Component Input (1EA)
RGB Input
HDMI Input(4EA)
Audio Input (3EA)
SPDIF Out(1EA)
USB
1
2
3
4
5
6
7
8
9
10
11
12
No
Item
Specification
Remark
Austria,Belgium,Bulgaria,Coratia,Czech,Denmark,Finland
,France,Germany,Greece,Hungary,Italy,Luxembourg,
Netherlands,Norway,Poland,Portugal,Rumania,Russia,
Serbia,Slovenia,Spain,Sweden,Switzerland,UK,Morocco,
Turkey
1) PAL/SECAM BG
2) PAL/SECAM DK
3) PAL I / II
4) SECAM L/L’
5) DVB T
Analog : Upper Heterodyne
Digital : COFDM
PAL, SECAM
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC
HDMI-PC
HDMI-DTV
RGB/DVI Audio, Component, AV
SPDIF OUT
For SVC, S/W Download, X-Studio
27 Country
EU(PAL Market)
Scart1 Jack is Full scart and support
RF-OUT(Analoge)
Scart2 Jack is Half scart and
support MNT-OUT
Side AV
Side AV
Analog(D-Sub 15Pin)
HDMI1/DVI,HDMI2,HDMI3,HDMI4
L/R Input
Side(X-Studio Only PG60 Series)
(5) 32” XGA Module
Display Screen Device
Aspect Ratio
PDP Module
Operating Environment
Storage Environment
Input Voltage
1
2
3
4
5
6
No
Item
Specification
Remark
32 inch Wide Color Display Module
16:9
PDP32G1####,
RGB Closed(Well) Type, Glass Filter(38%)
Pixel Format : 1024 horiz. By 720 ver.
1) Temp. : 0 ~ 40 deg
2) Humidity : 20 ~ 80 %
3) Temp. : -20 ~ 60 deg
4) Humidity : 10 ~ 90 %
100-240V~, 50/60Hz
PDP
LGE SPEC.
Maker LG
- 7 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet is applied to all of the PD81A chassis
manufactured at LG TV Plant all over the world.
Ex.) PD81A: 50PG6000-ZA, 42PG6000-ZA, 50PG7000-ZB,
manufactured at LG TV Plant all over the world.
Ex.) PD81A: 50PG6000-ZA, 42PG6000-ZA, 50PG7000-ZB,
60PG7000-ZB, 32PG6000-ZA ...
2. Specification.
[
Caution: The module keeping condition
1. The module keeping condition: The normal temperature
condition(more than 15°C)
--> Immediately the line supply.
--> Immediately the line supply.
2. The module keeping condition: 0°C
--> The module must be kept for more than 2 hours at the
normal temperature.
3. The module keeping condition: -20°C
--> The module must be kept for more than 3 hours at the
normal temperature.
4. The case of Gu-mi factory at the winter season.
--> The module must be kept for more than 5 minutes at
the heating zone(40°C~45°C).
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
there is no specific designation.
(4) The input voltage of the receiver must keep 100~240V,
50/60Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment.
O
After RGB Full White in HEAT-RUN Mode, the receiver
must be operated prior to the adjustment.
O
Enter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) Press the ADJ KEY on R/C and enter EZ ADJUST
2) Press the ADJ KEY on R/C and enter EZ ADJUST
Select “3. Test Pattern” by using
D
/
E
(CH +/-) and press
ENTER(
V
)
Select “White” by using
F
/
G
(VOL +/-) and press
ENTER(
V
)
- Set is activated HEAT run without signal generator in this
mode.
- Single color pattern (RED / BLUE / GREEN) of HEAT RUN
MODE uses to check panel.
- Caution: If you turn on a still screen more than 20 minutes
(Especially digital pattern, cross hatch pattern), an after
image may be occur in the black level part of the screen.
image may be occur in the black level part of the screen.
[
Caution
- Using ‘power on’ button of the control R/C, power on TV.
- All adjustment process is executed through RS-232C.
- Do not connect external input cable.
- All adjustment process is executed through RS-232C.
- Do not connect external input cable.
3. S/W Auto Download Using the
USB Memory Stick
[
Caution
- Using ‘power on’ button of the control R/C, power on TV.
- USB file (EPK) version must be bigger than downloaded
- USB file (EPK) version must be bigger than downloaded
version of main B/D.
(1) Insert the USB memory stick to the SET.
(2) Using ‘power on’ button of the control R/C, power on TV.
(3) S/W download process is executed automatically.
(2) Using ‘power on’ button of the control R/C, power on TV.
(3) S/W download process is executed automatically.
4. Auto-control Adjustment is Process
(1) All adjustment process is executed through RS-232C.
(2) Command send --> ADC Calibration --> Model name
(2) Command send --> ADC Calibration --> Model name
download --> EDID download.
(3) Auto-control adjustment protocol(RS-232C)
(4) Defined model name protocol (RS-232C)
- 8 -
5. Manual Model Name Download
(1) Press ADJ key on R/C for model name D/L
(2) Select “. Model Option” and press ENTER(
(2) Select “. Model Option” and press ENTER(
V
)
(3) Insert Option value by a number key
(4) Press the ENTER(
(4) Press the ENTER(
V
)
6. Manual ADC Adjustment
[
Caution
- Do not connect external input cable
- Adjustment result is applied to SET On/Off later.
- Adjustment result is applied to SET On/Off later.
[
Adjustment is done using internal ADC, so input signal is
not necessary.
(1) Press ADJ key on R/C for adjustment.
(2) Select “2. ADC calibration” by using
(2) Select “2. ADC calibration” by using
D
/
E
(CH +/-) and
press ENTER(
V
).
(3) Select “Start’ by using
F
/
G
(VOL +/-) and press
ENTER(
V
).
(4) ADC adjustment is executed automatically.
7. Manual EDID Download
(1) Press the ADJ KEY on R/C and enter EZ ADJUST.
(2) Select “5. EDID D/L” by using
(2) Select “5. EDID D/L” by using
D
/
E
(CH +/-) and press
ENTER(
V
).
(3) Select “Start” and press ENTER(
V
).
(4) EDID download is executed automatically.
(5) Press EXIT key on R/C.
(5) Press EXIT key on R/C.
8. EDID Data
(1) HDMI 1 (256 bytes)
(2) RGB (128 bytes)
=> Detail EDID Options are below(
,
,
,
)
1.
-> Product ID
2.
-> Serial No : Controlled on production line
3.
-> Month, Year : Controlled on production line
NO SIGNAL or White noise
NO SIGNAL
RF Input
AV / Component / RGB input
Click on the first or last page to see other 32PG6000-ZA (CHASSIS:PD81A) service manuals if exist.