DOWNLOAD LG 32LT75 / 32LT76 (CHASSIS:LD74A) Service Manual ↓ Size: 7.37 MB | Pages: 33 in PDF or view online for FREE

- 13 -

- One of R Gain / G Gain / B Gain should be kept on 80, and

others  are controlled lowering from 80 

1) Press ‘power on’ of the control R/C, set heat run to white by

pressing 

G

, and heat run over 15 minutes. (Set : RS-233

Host : PC, Baud Rate : 115200bps, Download : Cortez)

2) Zero Calibrate CA-210, and when controlling, stick the

sensor to the center of LCD module surface.

3) Double click In-start key on Controlling R/C and get in

‘white balance’.

4) Set test-pattern on and display inside pattern. Control is

carried out on three color temperature, COOL, MEDIUM,
WARM. (Control is carried out three times,)

5) When the R/G/B GAIN is 80 on OSD, it is the FULL

DYNAMIC Range of the Module. In order to control white
balance without the saturation of FULL DYNAMIC Range
and DATA, one of R Gain / G Gain / B Gain should be kept
on 80, and other two is controlled lowering from 80.

* Color Temperature: Cool, Medium, Warm

1) When R GAIN is set to 80

- Control G GAIN and B GAIN by lowering from 80. 

2) When B GAIN is set to 80

- Control R GAIN and G GAIN by lowering from 80.

3) When G GAIN is set to 80

- Control R GAIN and B GAIN by lowering from 80.

One of R Gain / G Gain / B Gain should be kept on 80,
and adjust other two lower than 80.
(When R/G/B GAIN are all 80, it is the FULL DYNAMIC
Range of Module)

- Remote controller for adjustment
- MSPG-925FS Pattern Generator

(Which has Video Signal : Color Bar Pattern shown in Fig.2)
-> Model : 232 / Pattern : 80

1) Input the Video Signal : Color Bar signal into AV1

(Using Full Scart Cable)

2) Set the PSM to Dynamic mode in Picture menu.
3) Press the IN-START key on R/C for adjustment
4) Press the TURBO-PICTURE key on R/C for adjustment
5) Press the 

G

(Vol.+) key operate To set , then it becomes

automatically.

6) Auto-RGB OK means adjustment is completed.

(1) Setting up like bottom figure (After setting white balance,

this is set)
1) Press ADJ Key in the Adjust remocon.
2) Select  “System Control 2” by using 

D

/

E

(CH+/-) key,

and press 

A

(ENTER).

3) Using Adjust remocon, RS-232 Host & Baud Rate &

Download value change (RS-232 Host:Gprobe, Baud
Rate:115200bps, Download:Cortez)

(2) Bar-code scanning

1) Push the menu button in DTV mode. 

Select the STATION -> Diagnostics -> To set

2) Check the Serial Number.

A u t o   C o l o r   B a l a n c e ( H e x )

   

A u t o- S c a r t R G B

T o   S e t 

R g a i n

1 6

G g a i n   1 6

B g a i n

1 4

Y G a i n

2 2

C b G a i n

2 2 

C r G a i n   1 A

R e s e t

T o S e t

S c a r t   R G B ( D V R )

N G

G

G

- 14 -

1) Does not  minute discharge at module. 
2) Non does not come into the front LED. 

Is the power cord plugged in?

Plug in the power cord.

Yes

No

Is the Line Filter and Power

Board Cable connected?

Connect the Cable.

Yes

No

Is the appropriate Fuse(F100) on

the Power Board?

Replace the Fuse.

Yes

No

Is the Power Board and 13P of

VSC Board Cable connected?

Connect the Cable.

Yes

No

After removing the cables, connect them to the Power Board(except the
SC101 connection cable), and change the AC voltage marking to manual.
When ST-BY 5V does not operate, replace the Power Board.

- 15 -

1) After lighting up once, it does not discharge 

minutely from module.

2) The rely falls.(there is an audible “click”) 
3) The color of the front LED turns from green to red.

Is the Power Board

normal ?

Replace the Power Board.

Is the output Low/High voltage normal

except for Stand-by 5V?

Yes

No

No

Is the each connector

normal?

Replace the connector.

After connecting each connector do

they operate normally? 

No

Yes

Yes

Is the VSC

Board normal?

Is the output voltage normal after

removing P900, P901 of VSC Board?

If it operates normally after removing the
P900, P901 : Replace the VSC Board

No

Yes

Does minute

discharge at Module?

Is the LVDC cable

normal?

Is the inverter on?

Check the LCD Module

Yes

No

YES

Yes

Reconnect the LVDS

cable in P1901

No

Is the IC700(FLI8548)

Output normal?

Replace the VSC.

No

Replace VSC board.
Is it ok?

YES

YES

No

Is the Low/High output voltage

normal except for stand-by 5V?

No

Replace the Power

board

Is the voltage (P900 5pin

on VSC) 0V or Low?

No

1) No OSD and image occur at screen. 
2) It maintains the condition where the front LED is green.

- 16 -

1) LED is green.
2) The minute discharge is continuously accomplished from the module.

Is the LVDS cable

normal ?

Is the VSC Board

normal?

Is the LVDS cable

connected?

Insert the Cable.

Yes

No

No

Yes

Does the FIL8548

IC(IC700) operate?

Replace the FIL8548

IC(IC700)

No

Is the Ctrl Board of

Module normal?

Replace the Ctrl B/D.

No

No

Yes

Replace the VSC B/D.

Replace the cable.

Yes