DOWNLOAD LG 32LG80UR (CHASSIS:LP81G) Service Manual ↓ Size: 2.56 MB | Pages: 32 in PDF or view online for FREE

- 9 -

This spec. sheet is applied all of the 32” LCD TV, LP81G
chassis (HURRICANE 5-Modified) by manufacturing LG TV
Plant all over the world.

1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help protect test instrument.

2) Adjustment must be done in the correct order.
3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.

4) The input voltage of the receiver must keep 100-220V,

50/60Hz.

5) Before adjustment, execute Heat-Run for 15 minutes at RF

no signal.

(1) Download method 1  (PCB Assy)

- HD

(2) Connect the download jig to D-sub jack

(1) Execute ‘ISP Tool’ program in PC, then a main window will

be opened

(2) Click the connect button and confirm “Dialog Box”.

(3) Click the Config button and Change speed

E2PROM Device setting : over the 350Khz

(4) Read and write bin file

Click “(1)Read” tab, and then load download file(XXXX.bin)
by clicking “Read”.

(5).Click “Auto(2)” tab and set as below
(6).click “Run(3)”.
(7).After downloading, check “OK(4)” message.

 

 

( 1 ) 

 

                f i l ex x x .bi n

 

 

     

     f i l ex x x .bi n

(4)

 

.......... OK

)

( 3

( 2 )

 

- 10 -

(1) Put the USB Stick to the USB socket 

(2) Automatically detecting update file in USB Stick

(3) Select “Start” Button and  press “ok” button
(4) Updating is staring.

(5) After finish firmware update, The TV set reset detect the

update file automatically.

* Required Equipments

- Remote controller for adjustment
- MSPG-925F Pattern Generator

(1) Convert to RGB PC in Input-source
(2) Input the PC 1024x768 @ 60Hz 1/2 Black & White Pattern

into RGB.(MSPG-925F model:60, pattern:54)

(3) Adjust  by  commanding AUTO_COLOR_ADJUST(0xF1)

0x00 0x02 instruction.

(1) We confirm whether “0xF1 (offset), 0xF2 (gain)” address of

EEPROM “0xBC” is “0xAA” or not.

(2) If “0xF1”, “0xF2” address of EEPROM “0xBC” isn’t “0xAA”,

we adjust once more

(3) We  can confirm the ADC values from “0x00~0x05”

addresses in a page “0xBC”

* Manual ADC process using Service Remocon. After enter

Service Mode by pushing “ADJ” key, execute “Auto-RGB” by
pushing “

G

” key at “Auto-RGB”.

(1) Convert to Component in Input-source
(2) Input the Component (Which has 720p@60Hz YPbPr

signal : 100% Color Bar into Component. (MSPG-925F
Model: 217/ Pattern: 65 )

(3) Adjust  by  commanding AUTO_COLOR_ADJUST (0xF1)

0x00 0x02 instruction

(1) We confirm whether “0xF3 (offset), 0xF4 (gain)” address of

EEPROM “0xBC” is “0xAA” or not.

(2) If “0xF3”, “0xF4” address of EEPROM “0xBC” isn’t “0xAA”,

we adjust once more.

(3) We  can confirm the ADC values from “0x06~0x0B”

adresses in a page “0xBC”.

* Manual ADC process using Service Remocon. After enter

Service Mode by pushing “ADJ” key, execute “Auto-RGB” by
pushing “

G

” key at “Auto-RGB”

Before PCBA check, you have to change the Tool option, Area
option and have to AC off/on (Plug out and in)
(If missing this process, set can operate abnormally)

(1) Equipment : adjustment remote control.
(2) Profile : Must be changed the option value because being

different with some setting value depend on
module maker, inch and market.

(3) Adjustment method

The input methods are same as other chassis.(Use IN-
START Key on the Adjust Remocon.)
(If not changed the option, the input menu can differ the
model spec.)
* Refer to Job Expression of each main chassis ass’y

(EBTxxxxxxxx) for Option value  

* Never push the IN-STOP KEY after completing the function

inspection.

** After TOOL Option/ Area Option change, you have to AC

off/oon (Plug out and in)

Before PCBA check , you ha ve to change the Tool opition,
Area option and have to AC off/on (Plug out and in)
(If missing this process, set can operate abnormally)

(1) Push In-start key on Adjust remote-control.
(2) Check “ MainV3.xx USB V3.xx”

* Caution

Use the proper signal cable for EDID Download

* Caution:

- Never connect HDMI & D-SUB Cable at the same time.
- Use the proper cables below for EDID Writing

* EDID Data

<Analog : 128bytes>

<HDMI 1 : 256bytes> / <HDMI 2 : 256bytes>
The data is same without Physical address

-> Physical address(F) : HDMI 1 -> 10, HDMI 2 -> 20

- 11 -

Item

Manufacturer ID

Version

Revision

Condition

GSM

Digital : 1

Digital : 3

Data

1E6D

01

03

For HDMI EDID

For RGB EDID

- 12 -

- Detail EDID Options are below (A, B, C, D, E, F) 

A. Product ID
B. Serial No:  Controlled on production line
C. Month, Year: Controlled on production line:

ex)  Monthly: ‘09  ‘09

Year:  ‘2007 ->  ‘11’

D. Model Name(Hex): 

E. Checksum: Changeable by total EDID data

(1) Connect D-sub Signal Cable to D-Sub Jack
(2) Input HDCP key with HDCP-key- in-program
(3) HDCP Key value is stored on EEPROM(AT24C64) which

is From “0x80” addresses of 0xA0 page

(4) AC off/ on and on HDCP button of MSPG925 and confirm

whether picture is displayed or not of using MSPG925

(5) HDCP Key value is different among the sets.
* Before HDCP Download, you have to Set th Configuration
that CMD delay. -> Configuration -> Option -> I2C(16 Byte
Write : 20ms, 128 Byte Read : 20ms, Read CMD Byte : 0.5ms,
I2C Clock : 45KHz

(1) Purpose : Adjust the color temperature to reduce the

deviation of the module color temperature.

(2) Principle : To adjust the white balance without the

saturation, Fix the one of R/G/B gain to C0 and
decrease the others.

(3) Adjustment mode : Two modes of Cool and Warm

(Medium data is automatically calibrated by the Cool data)

(4) Required Equipment

1) Remote controller for adjustment 
2) Color Analyzer : CA100+ or CA-210 or same product,

(Should be used in the calibrated ch by CS-1000 (CH9)

3) Auto W/B adjustment instrument(only for Auto

adjustment)

(1) Enter the adjustment mode of DDC

- Set command delay time : 50ms
- Enter the DDC adjustment mode at the same time heat-

run mode when pushing the power on by power only key

- Maintain the DDC adjustment mode with same condition

of Heat-run (Maintain after AC off/on in status of Heat-run
pattern display)

(2) Release the DDC adjustment mode

- Release the adjust mode after AC off/on or std-by off/on in

status of finishing the Hear-run mode

- Release the Adjust mode when receiving the aging off

command(F3 00 00) from adjustment equipment

- Need to transmit the aging off command to TV set after

finishing the adjustment.

- Check DDC adjust mode release by exit key and release

DDC adjust mode

(3) Enter the adjust mode of white balance

- Enter the white balance adjustment mode with aging

command(F3, 00, FF)

* Luminance min value is 200cd/m

2

≥ in the cool mode (For LCD)

(1) Adjustment mode : Two modes (Cool and Warm)

(Medium data is automatically calibrated by the Cool data)

(2) Color analyzer(CA100+, CA210) should be used in the

calibrated ch by CS-1000(LCD : CH9, PDP : CH10)

(3) Operate the zero-calibration of the CA100+ or CA-210,

then stick sensor to the module when adjusting.

(4) For manual adjustment, it is also possible by the following

sequence.

1) Select white pattern of heat-run by pressing “POWER

ON” key on remote control for adjustment then operate
heat run longer than 15 minutes. (If not executed this
step, the condition for W/B may be different.)

2) Push “Exit” key.
3) Change to the AV mode by remote control.(Push front-

AV or Input key)

4) Input external pattern(85% white pattern)
5) Push the ADJ key two times (entering White Balance

mode)

6) Stick the sensor to the center of the screen and select

each items (Red/Green/Blue Gain and Offset) using

D

/

E

(CH +/-) key on R/C.

7) Adjust R/ G/ B Gain using F/G(VOL +/-) key on R/C.
8) Adjust two modes (Cool and Warm)

(Fix the one of R/G/B and change the others)

9) When adjustment is completed, Exit adjustment mode

using EXIT key on R/C.

Model name

Model Name(HEX)

LG TV

00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20