DOWNLOAD LG 22LK230-MA (CHASSIS:LP92R) Service Manual ↓ Size: 4.02 MB | Pages: 36 in PDF or view online for FREE

- 9 -

(1) Profile : Must be changed the Area option value because

being different of each Country’s Language and
signal Condition.

(2) Equipment : Adjustment remote control.
(3) Adjustment method 

- The input methods are same as other chassis.(Use IN-

START key on the Adjustment remote control.)

Refer to Job Expression of each main chassis assembly
(EBTxxxxxxxx) for Option value.

- Purpose : Adjust the color temperature to reduce the

deviation of the module color temperature.

- Principle : To adjust the white balance without the saturation,

Fix the one of R/G/B gain to 192 (default data)
and decrease the others.

- Adjustment mode : Three modes - Cool / Medium / Warm

(Medium data is automatically calibrated by the Cool data)

- Required Equipment

1) Remote control for adjustment 
2) Color Analyzer : CA100+ or CA-210 or same product

- LCD TV(ch : 9)
(should be used in the calibrated ch by CS-1000)

3) Auto W/B adjustment instrument(only for auto adjustment)

5.2.1. Connecting diagram of equipment for measuring

(For Automatic Adjustment)

* LP92A Support I2C Interface For ADC/DDC Adjustment.

(1) Enter the adjustment mode of DDC

- 22 Set command delay time : 50 ms
- Enter the DDC adjustment mode at the same time heat-

run mode when pushing the power on by power only key.

- Maintain the DDC adjustment mode with same condition

of Heat-run => Maintain after AC off/on in status of Heat-
run pattern display)

(2) Release the DDC adjustment mode

- Release the adjust mode after AC off/on or std-by off/on

in status of finishing the Hear-run mode

- Release the Adjust mode when receiving the aging off

command(WB 00 FF) from adjustment equipment.

- Need to transmit the aging off command to TV set after

finishing the adjustment.

- Check DDC adjust mode release by exit key and release

DDC adjust mode)

(3) Enter the adjust mode of white balance

- Enter the white balance adjustment mode with aging

command (F3, 00, 00)

(4) Release the adjust mode of white balance

- Release the white balance adjustment mode with aging

command(F3, 00, FF)

* Luminance min value is 150cd in the Cool/Medium/Warm

mode(For LCD)

5.2.2. Adjustment of White Balance (for Manual adjustment)

(1) Color analyzer(CA100+, CA210) should be used in the

calibrated ch by CS-1000

(2) Operate the zero-calibration of the CA100+ or CA-210,

then stick sensor to the module when adjusting.

(3) For manual adjustment, it is also possible by the following

sequence.

1) Select white pattern of heat-run by pressing “POWER

ON” key on remote control for adjustment then operate
heat run longer than 15 minutes. (If not executed this
step, the condition for W/B may be different.)

2) Push “Exit” key.
3) Change to the AV mode by remote control.
4) Input external pattern (85 % white pattern)
5) Push the ADJ key two time(entering White Balance

mode) -> Enter “04 13” (Password)

6) Stick the sensor to the center of the screen and select

each items (Red/Green/Blue Gain and Offset) using

D

/

E

(CH +/-) key on R/C..

7) Adjust R/ G/ B Gain using 

F

/

G

(VOL +/-) key on R/C.

8) Adjust three modes all (Cool/ Medium/ Warm) : Fix the

one of R/G/B gain and change the others.

9) When adjustment is completed, Exit adjustment mode

using EXIT key on R/C.

* CASE

First adjust the coordinate far away from the target value(x, y).
1) x, y > target

i) Decrease the R, G. 

2) x, y < target

i) First decrease the B gain, 
ii) Decrease the one of the others.

3) x > target, y < target

i) First decrease B, so make y a little more than the target.
ii) Adjust x value by decreasing the R

4) x < target, y > target

i) First decrease B, so make x a little more than the target.
ii) Adjust x value by decreasing the G

(4) Standard color coordinate and temperature when using the

CA100+ or CA210 equipment

(Small size inch’s color coordinate is different from others,

So use below table.)

To check the Coordinates of White Balance, you have to
measure at the below conditions.
Picture Mode : User 1
Dynamic Contrast : Off
Dynamic Colour : Off
(If you miss the upper condition, the coordinates of W/B
can be lower than the spec.)

Coordinate 

Mode 

x y 

Temp

uv∆

Cool 0.280 

± 0.002

0.283 

± 0.002

9,300 

K

0.000

Medium

0.290 ± 0.002

0.295 ± 0.002

8,000 K

0.000

Warm

0.308 ± 0.002

0.319 ± 0.002

6,500 K

0.000

- 10 -

300

200

530

540

401

400

900

510

120

LV

1

910

810

A2

A10

820

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by       in the Schematic Diagram and EXPLODED VIEW. 
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. 
Do not modify the original design without permission of manufacturer.

THE    SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE    SYMBOL MARK OF THE SCHEMETIC.

[AV]

MNT_ROUT

CVBS_LIN

D102
30V

R104

10K

R101

12K

R103

10K

D107

30V

CVBS_RIN

MUTE_LINE

R102
12K

MNT_LOUT

CVBS_VIN

R110
75

D108

30V

D101
30V

MUTE_LINE

C105
10uF

16V

C104
10uF

16V

C106

560pF

50V

READY

C107

560pF
50V

READY

R128

1K

R127

1K

C103

5600pF

50V

C102

5600pF

50V

R109
220K

R108
220K

JK101

PPJ234-03

5A

[RD1]O-SPRING

6A

[RD1]E-LUG

4A

[RD1]CONTACT

7B

[WH1]E-LUG-S

5B

[WH1]O-SPRING

7C

[RD2]E-LUG-S

5C

[RD2]O-SPRING

4C

[RD2]CONTACT

5D

[WH2]O-SPRING

4E

[YL]CONTACT

5E

[YL]O-SPRING

6E

[YL]E-LUG

16.5V_AOUT

R114

47

FOR DEBUG

Q101

ISA1530AC1

FOR DEBUG

E

B

C

R106

220

FOR DEBUG

R111

470

FOR DEBUG

R112

68

FOR DEBUG

JP101

MNT_VOUT_T

ZD101
SD05
ZD102
SD05

Q105

MMBT3904(NXP)

E

B

C

Q106

MMBT3904(NXP)

E

B

C

Q102

MMBT3904(NXP)

FOR DEBUG

E

B

C

Q103

MMBT3904(NXP)

E

B

C

Q104

MMBT3904(NXP)

E

B

C

INPUT

INPUT

EAX64207701

2011/5/6

1  7

POP NOISE

POP NOISE

AV IN/OUT

GAIN X 4

FOR DEBUG

THE    SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE    SYMBOL MARK OF THE SCHEMETIC.

TXCE3+

TXCE3-

TXCLKE+

TXCLKE-

TXCE2+

TXCE2-

TXCE1+

TXCE1-

TXCE0+

TXCE0-

LED_KEY

L203

MBW3216-501TF

500-ohm

LED_POWER

ST_5V

3.3V_M

IR

KEY1

5V_LCD

TXCE0+,TXCE0-,TXCE1+,TXCE1-,TXCE2+,TXCE2-,TXCE3+,TXCE3-,TXCLKE+,TXCLKE-

C206
100pF

50V

READY

C205
47pF
50V

READY

C209

100pF

50V

READY

C208
100pF
50V

C204
100pF

50V

READY

C203
0.1uF
50V

C202
0.1uF
50V

READY

C201
0.1uF
50V

C207
0.1uF
50V

C212
100pF
50V

READY

KEY2

ST_3.3V

R203

10K

R206
4.7K

P201

12507WR-08L

1

KEY1

2

KEY2

3

GND

4

+ST_5V

5

GND

6

IR

7

LED_KEY

8

LED_POWER

9

R230

0

JEIDA

P204

FF10001-30

1

30

2

29

3

28

4

27

5

26

6

25

7

24

8

23

9

22

10

21

11

20

12

19

13

18

14

17

15

16

16

15

17

14

18

13

19

12

20

11

21

10

22

9

23

8

24

7

25

6

26

5

27

4

28

3

29

2

30

1

31

.

R229

0

22"LGD/Tsinghua

ZD200

5.6V

READY

ZD204
5.6V

READY

ZD205
5.6V

READY

ZD201

5.6V

ZD202

5.6V

READY

IR & LED

LVDS/IR_LED_KEY

HD(22")

LVDS/IR/KEY

EAX64207701

2011/5/6

2  7