DOWNLOAD LG GR-P207DTU Service Manual ↓ Size: 8.05 MB | Pages: 127 in PDF or view online for FREE

Installation

1. Place your appliance where it is easy to

use.

2. Avoid placing the unit near heat sources,

direct sunlight or moisture.

3. Air must circulate properly around your

appliance to ensure efficient operation. If
your appliance is placed in a recessed
area in the wall, allow at least a 12 Inches
(30 cm) or greater clearance above the
appliance and 2 inches (5 cm) or more
from the wall. The appliance should be
elevated 1 inch (2.5 cm) from the floor,
especially if it is carpeted.

5. Don't install the appliance below 5

°C. It may cause affect the performance. 

4. To avoid vibrations, the appliance must be leveled.

Failure to do so could result in death or serious injury.

Electric Shock Hazard 
Disconnect electrical supply to refrigerator before installing. 

Remove the lower cover by lifting upward, and
then pull up the feed water tube while pressing
area 

c shown in the figure to the right.

Installation

1) Removing the hinge cover by loosening the

screws. Separate all connection wires except
for the earth line after.

2) Remove the keeper by rotating it counter

clockwise (

c) and then lifting the upper

hinge up (

d).

3) Remove the freezer compartment door by

lifting it upward. This time, the door should
be lifted enough for the feed water pipe tube
to be completely pulled out.

1) Loosen the hinge cover screws and remove

the cover. Remove connection wire, if any,
except for the earth line.

2) Remove keeper by rotating it clockwise (

c)

and then remove the upper hinge by lifting
it up (

d ).

3) Remove the refrigerator compartment door

by lifting it up.

•

If a tube end is deformed or abraded, cut the part away.

•

When removing the upper hinge, be careful that the door does not fall forwards .

•

Move the refrigerator compartment door passing through the access door and lay
it down, but be careful not to damage the feed water pipe tube.

Lower cover

Lower hinge

Lower hinge

Keeper

Feed water tube

Connection
wires

Connection

wires

Hinge
cover

Upper hinge

Upper hinge

Keeper

Upper hinge

Earth line

Pass the refrigerator laterally through the access
door as shown in the right figure.

„

Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5
kgf/cm

2

) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).

„

If water pressure does not reach the rating 147 kPa (1.5 kgf/cm

2

) or below, it is

necessary to purchase a separate pressure pump for normal automatic icing and
cool water feed.

„

Keep the total length of the feed water pipe tube within 12 m and be careful for the
tube not be bent. If the tube is 12 m or longer it may cause trouble in water feed
owing to the drain water pressure.

„

Install the feed water pipe tube at a place free from heat.

„

Connect to potable water supply only.

„

Refer to instructions with water filter kit for installation.

Mount them in the reverse sequence of removal after they pass through the access
door.

1

2

3

4

5

Ma

x

FR

Z

TEMP

RE

F

TEMP

Min

5

4

3

2

1

Max

Installation

Level the door by inserting flat ( - type) driver into the groove of the left height adjusting
screw and rotate it clockwise (

c).

Level the door by inserting flat ( - type) driver into the groove of the right height
adjusting screw and rotate it clockwise (

c).

The refrigerator doors will close smoothly by heightening the front side by adjusting
the height adjusting screw. If the doors do not close correctly, performance may be
affected.

Installation

c

c

1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.

2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their

proper places. They are packed together to prevent possible damage during shipping.

3. Connect the power supply cord (or plug) to the outlet. Don't double up with other

appliances on the same outlet.