LG GR-P207DTU Service Manual ▷ View online
5. DISPENSER
1) Disconnect button assembly by pulling down until it
stops and then pulling forward.
2) Remove display frame Assy by making a gap between a
display frame Assy. and funnel Assy. with a balde
screwdriver and pulling it forward. The cover dispenser
is fixed with a hook.
screwdriver and pulling it forward. The cover dispenser
is fixed with a hook.
3) Display Assy can be disconnected by pressing the
upper part of a cover dispenser and pushing a display
Assy. after disconnecting display frame Assy. housing.
Assy. after disconnecting display frame Assy. housing.
4) Loosen four screws with a phillips screwdriver and pull a
funnel Assy to disconnect.
5) Duct cap Assy is disconnected if hold lever connecting
screw is loosened with a phillips screwdriver.
6) For assembling a duct cap Assy., insert one end of a
spring into the right hole of dispenser lever, and insert
the other end into the right hole in upper part of
dispenser. And then assemble a holder lever after fixing
a holder at a solenoid Assy working part.
the other end into the right hole in upper part of
dispenser. And then assemble a holder lever after fixing
a holder at a solenoid Assy working part.
HOW TO DISASSEMBLE AND ASSEMBLE
- 113 -
Button
Funnel Assy
Funnel
Assy
Assy
Holder
Lever
Solenoid Assy
Cap Assy,Duct
Spring
Heater, Sheet
Lever,Dispenser
Solenoid Assy
7) Dispenser Related Parts
HOW TO DISASSEMBLE AND ASSEMBLE
- 114 -
7
12
13
8
11
14
17
15
24
16
23
21
1
22
9
10
2
4
18
21
19
1
FRAME ASSY, DISPLAY
2
COVER, DISPENSER
4
PWB(PCB) ASSY, DISPLAY
7
FUNNEL ASSY
8
SWITCH, MICRO
9
FRAME, FUNNEL
10 LEVER(SWITCH)
11 FUNNEL
12 RUBBER, FUNNEL
13 SWITCH, ROCKER
14 SOLENOID ASSY
15 SPRING
16 HOLDER, LEVER
17 CAP, DUCT
19 LEVER, DISPENSER
20 RUBBER, CAP
21 BUTTON ASSY
22 BUTTON
23 HOLDER, BUTTON
24 DECO, DRAIN
< 17 Cap Assy, Duct Detailed Drawings>
TROUBLE DIAGNOSIS
- 74 -
CLAIMS.
CAUSES AND CHECK POINTS.
HOW TO CHECK
3. Refrigeration
is weak.
Plate
heater
heater
Cord
heater
heater
1) Refrigerant Partly leaked.
2) Poor defrosting capacity.
Drain path (pipe) clogged.
Defrost heater does not
generate heat.
generate heat.
Weld joint leak.
Parts leak.
Parts leak.
Inject P/U into drain hose.
Foreign materials
penetration.
penetration.
Cap drain is not disconnected.
Inject through the
hole.
Seal with drain.
hole.
Seal with drain.
P/U lump input.
Screw input.
Other foreign materials
input.
Screw input.
Other foreign materials
input.
Parts
disconnected.
disconnected.
Wire is cut.
- Heating wire.
- Contact point
- Contact point
between heating
and electric wire.
and electric wire.
Dent by fin evaporator.
Poor terminal contacts.
Poor terminal contacts.
Wire is cut.
- Lead wire.
- Heating wire.
- Contact point
- Heating wire.
- Contact point
between heating and
electric wire.
electric wire.
Heating wire is corroded
- Water penetration.
Bad terminal connection.
■
Check visually.
■
Check terminal
Conduction: OK.
No conduction: NG.
If wire is not cut, refer to
resistance.
P=Power
V=Voltage
R=Resistance
Conduction: OK.
No conduction: NG.
If wire is not cut, refer to
resistance.
P=Power
V=Voltage
R=Resistance
V
2
P= —
R
V
2
R= —
P
6. WATER TANK AND WATER LINE
u
The water tank at back and lower part of a refrigerator is
fixed by one screw and has a capacity containing 7
glasses (180cc per glass) of cold water. It will take time
to make more cold water in the tank.
fixed by one screw and has a capacity containing 7
glasses (180cc per glass) of cold water. It will take time
to make more cold water in the tank.
* The first portion of dispensed water is not cold even
though the refrigerator is working. In this case,
dispense ice first in the cup and then water to make a
cold water.
dispense ice first in the cup and then water to make a
cold water.
7. HOME BAR
7-1. Home Bar related parts
7-2. Home Bar parts disassembly and assembly
1) Disconnect H/Bar Door Assy
a
.
2) Loosen two screws
g
attached on the refrigerator
compartment door with a phillips screwdriver. And
loosen 4 screws
loosen 4 screws
b
and two screws
c
. Pull H/Bar door
Assy
a
. forward to disassemble.
3) Loosen two screws
j
,
i
fixed on H/Bar door Assy. and
two screws
k
with a cross driver to disassemble arm
Assy.
4) Assemble parts by performing the disassembly in
reverse order.
Note :
• Assemble carefully parts
g
,
j
,
k
until they are
fixed firmly when assembling them.
• Adjust exterior gap by adjusting parts
b
,
g
and
when assembling.
HOW TO DISASSEMBLE AND ASSEMBLE
- 115 -
1
8
6
7
5
11
10
9
8
7
6
4
3
11
10
9
2.0
5.0
1.8
1.8
1 DOOR ASSY, H/BAR
7 SCREW TAP TITE(ARM)
2 SEREW, TAP TITE(HINGE-H/B)
8 ARM ASSY
3 SCREW MACHINE(HINGE-H/B)
9 STOPPER
4 HINGE ASSY H/BAR
10 SCREW, MACHINE(STOP ARM-H/B)
5 HINGE ASSY H/BAR
11 SCREW MACHINE(HINGE-H/B)
6 CAP, ARM
Click on the first or last page to see other GR-P207DTU service manuals if exist.