DOWNLOAD LG GR-P207DTU Service Manual ↓ Size: 8.05 MB | Pages: 127 in PDF or view online for FREE

- 89 -

Ice in the freezer 1) Bad cooling air circulation.

- Check food storage conditions 

- Be acquainted with how to use.

- Check the p

arts related

compartment.

- Intake port is colgged in the freezer

visually.(Check clogging at intake 

- Check defrost (Check ice on the

to defro

sting if the 

- Surface of fan

compartment.

and discharging port of cooling air.)

evaporator and pipes after forced

problem is caused by

grille.

- Discharging port is Clogged.

- Check food occupation ratio in 

defrosting).

the faulty defrosting.

- Wall of freezer

- Too much food is stored.

volume(Less than 75%).

compartment.

- Bad defrosting.

- Check frost on the evaporator after

- Cool air

dissembling shroud and fan grille.

discharging port.

- Check icing at intake port of 

- Basket(rack)

refrigerator compartment.

area.

- Food surface.

2) Bad freezer compartment door

- Check gasket attachment 

- Correct the gasket attachement

- Replace when it can n

ot

- Icing in the

- Faulty gasket

conditions.

conditions and replace it.

be repaired.

shute.

- Faulty assembly

- Check door assembly conditions.

- Door assembly and replacement.

3) Over freezing in the freezer 

- Refrigerator operates pull down.

-Replace defective parts.

compartment.

(Check if it is operated 

- Faulty MICOM.

intermittently)

- The Temperature of freezer 

compartment is satisfactory, but 

over freezing happens in the 

refrigerator compartment even 

though the notch is set at "weak".

4) Bad defrosting.

- Check frost on the evaporator after

- Check parts related to defrosting.

- Heater wire is cut.

dissembling shroud and grille.

- Check defrosting.(Check ice on the

- Faulty defrost sensor.

- Check ice on the intake port in the

evaporator and pipes after forced

- Defrosting cycle

refrigerator compartment.

defrosting.)

5) User is not familiar with how to 

- Check food holds door open.

- Be acquainted with how to use.

use.

- Check ice on the ice tray.

- Door opens.

- High moisture food(water) is stored.

- 122 -

• Pull a water supply tube 

b

forward while pressing 

a

part

to disconnect water supply tube as shown below.

(1)  Loosen hinge cover screw of freezer door and remove

cover.  
Disconnect all connecting lines except earthing cord.

(2) Turn hinge lever in arrow  A  direction until it is

loosened and take it out in arrow  B  direction. 

• When disconnecting refrigerator door, turn hinge

lever counterclockwise.

• If hinge lever or bracket hinge pin is deformed

during assembling freezer and refrigerator doors,
fix two screws (Tap Tite Screw, M6: Hinge, L fixing
screw) in the hole of upper hinge.

(3) Disconnect upper hinge 

a

from a hinge supporter 

b

by grasping the front part of upper hinge and lifting up
(Hinge Assy, U) in arrow direction  A  and pull forward
in arrow  B  direction. Be careful as the door may be
fallen down. 

(4) Lift up the freezer door 

a

in arrow direction and

disconnect the door from the lower hinge 

b

. Don’t pull

a door forward.

• Lift up a freezer door until a water supply tube is

fully taken out.

(5) Assembly is the reverse order of disassembly

- 111 -

2

1

A

A

B

1

2

1

2

Cover, Hinge

2

Connecting

Line

Earthing

Cord

Lever, Hinge

A

B

1) Put blade screwdriver into a groove on the side of a

Deco handle and lift up a little bit in arrow 

a

direction

and push up with hand in arrow 

b

direction and

disconnect.

2) Put blade screwdriver into a groove on the side of a

DECO handle and lift up in arrow direction 

c

and push

down with hand in arrow direction 

d

and disconnect.

3) Push up a piece handle 

c

in arrow direction with hand

and disconnect.

4) Turn screw in arrow direction with a cross driver and

disconnect.

1) Loosen two screws after disconnecting a cap screw of a

grille fan(U) with a balde screwdriver.

2) Disassembly of a grille fan(U) : Pull forward after

opening hook at 

➝

part with a blade screwdriver.

3) Disconnect housing  A  of a grille fan (L) from the main

body.

4) Disassembly of a grille fan (L) : Hold  upper part of a

grille fan(L) and pull forward carefully.

5) Loosen two screws.

6) Disassembly of shroud. F(U) : Disconnect housing of  B

after removing two rail guides with a blade screwdriver. 

7) Disassembly of shroud. F(U) : Hold upper part and pull

forward.

8) Check foam PU sticking conditions around a shroud,

F(U) and F(L)  during assembling.  If damaged, torn or
badly sticked, assemble with a new one after sealing
well.

1) How to disassemble:

(1) Remove ice bank from the freezer compartment.

(2) Loosen two screws on the upper part of icemaker

bracket.

(3) Disconnect icemaker bracket so that it can slide

forward.

(4) Disconnect icemaker housing and sensor housing.

(5) Disconnect icemaker horizontally by pressing bracket

hook part. ( Don’t disassemble further. The set value
may be changed.)

2) How to assemble : The assembly is the reverse order of

the above disassembly.  

When the ice tray is not horizontal after assembly,
assembly must be wrong. Check and assemble
again.

- 112 -

1

Handle, Deco

2

3

4

Handle, Piece

Screw

Bracket, Ice Maker

Hook

Ice Maker Unit

Lever

Tray, Ice

Sensor

Insulation

Cover, Sensor