DOWNLOAD LG GR-L247ER Service Manual ↓ Size: 5.74 MB | Pages: 127 in PDF or view online for FREE

• Pull a water supply tube 

b

forward while pressing 

a

part

to disconnect water supply tube as shown below.

(1)  Loosen hinge cover screw of freezer door and remove

cover.  
Disconnect all connecting lines except earthing cord.

(2) Turn hinge lever in arrow  A  direction until it is loosened

and take it out in arrow  B  direction. 

• When disconnecting refrigerator door, turn hinge

lever counterclockwise.

• If hinge lever or bracket hinge pin is deformed

during assembling freezer and refrigerator doors,
fix two screws (Tap Tite Screw, M6: Hinge, L fixing
screw) in the hole of upper hinge.

(3) Disconnect upper hinge 

a

from a hinge supporter 

b

by grasping the front part of upper hinge and lifting up
(Hinge Assy, U) in arrow direction  A  and pull forward in
arrow  B  direction. Be careful as the door may be fallen
down. 

(4) Lift up the freezer door 

a

in arrow direction and

disconnect the door from the lower hinge 

b

. Don’t pull

a door forward.

• Lift up a freezer door until a water supply tube is

fully taken out.

(5) Assembly is the reverse order of disassembly

- 99 -

2

1

A

A

B

1

2

1

2

Cover, Hinge

2

Connecting

Line

Earthing

Cord

Lever, Hinge

A

B

1) Put blade screwdriver into a groove on the side of a

Deco handle and lift up a little bit in arrow 

a

direction

and push up with hand in arrow 

b

direction and

disconnect.

2) Put blade screwdriver into a groove on the side of a

DECO handle and lift up in arrow direction 

c

and push

down with hand in arrow direction 

d

and disconnect.

3) Push up a piece handle 

c

in arrow direction with hand

and disconnect.

4) Turn screw in arrow direction with a cross driver and

disconnect.

1) Loosen two screws after disconnecting a cap screw of a

grille fan(U) with a balde screwdriver.

2) Disassembly of a grille fan(U) : Pull forward after

opening hook at 

➝

part with a blade screwdriver.

3) Disconnect housing  A  of a grille fan (L) from the main

body.

4) Disassembly of a grille fan (L) : Hold  upper part of a

grille fan(L) and pull forward carefully.

5) Loosen two screws.

6) Disassembly of shroud. F(U) : Disconnect housing of  B

after removing two rail guides with a blade screwdriver. 

7) Disassembly of shroud. F(U) : Hold upper part and pull

forward.

8) Check foam PU sticking conditions around a shroud,

F(U) and F(L)  during assembling.  If damaged, torn or
badly sticked, assemble with a new one after sealing
well.

1) How to disassemble:

(1) Remove ice bank from the freezer compartment.

(2) Loosen two screws on the upper part of icemaker

bracket.

(3) Disconnect icemaker bracket so that it can slide

forward.

(4) Disconnect icemaker housing and sensor housing.

(5) Disconnect icemaker horizontally by pressing bracket

hook part. ( Don’t disassemble further. The set value
may be changed.)

2) How to assemble : The assembly is the reverse order of

the above disassembly.  

When the ice tray is not horizontal after assembly,
assembly must be wrong. Check and assemble
again.

- 100 -

1

Handle, Deco

2

3

4

Handle, Piece

Screw

Bracket, Ice Maker

Hook

Ice Maker Unit

Lever

Tray, Ice

Sensor

Insulation

Cover, Sensor

1) Disconnect button assembly by pulling down until it

stops and then pulling forward.

2) Remove display frame Assy by making a gap between a

display frame Assy. and funnel Assy. with a balde
screwdriver and pulling it forward. The cover dispenser
is fixed with a hook. 

3) Display Assy can be disconnected by pressing the upper

part of a cover dispenser and pushing a display Assy.
after disconnecting display frame Assy. housing.

4) Loosen four screws with a phillips screwdriver and pull a

funnel Assy to disconnect.

5) Duct cap Assy is disconnected if hold lever connecting

screw is loosened with a phillips screwdriver.

6) For assembling a duct cap Assy., insert one end of a

spring into the right hole of dispenser lever, and insert
the other end into the right hole in upper part of
dispenser. And then assemble a holder lever after fixing
a holder at a solenoid Assy working part. 

- 101 -

Button

Funnel Assy

Funnel
Assy

Holder

Lever

Solenoid Assy

Cap Assy,Duct

Spring

Heater, Sheet

Lever,Dispenser

Solenoid Assy

7) Dispenser Related Parts

- 102 -

18

21

19

1

FRAME ASSY, DISPLAY

2

COVER, DISPENSER

4

PWB(PCB) ASSY, DISPLAY

7

FUNNEL ASSY

8

SWITCH, MICRO

9

FRAME, FUNNEL

10 LEVER(SWITCH)

11 FUNNEL

12 RUBBER, FUNNEL

13 SWITCH, ROCKER

14 SOLENOID ASSY

15 SPRING

16 HOLDER, LEVER

17 CAP, DUCT

19 LEVER, DISPENSER

20 RUBBER, CAP

21 BUTTON ASSY

22 BUTTON

23 HOLDER, BUTTON

24 DECO, DRAIN