LG MS-2042W Service Manual ▷ View online
5-14
CONDITION
CHECK
RESULT
CAUSE
REMEDY
1. Setting time
does not count
down when
touching START
pad.
down when
touching START
pad.
2. Fan motor or
oven lamp do
not turn on.
not turn on.
No continuity.
Continuity.
Continuity
Defective PCB
assembly.
assembly.
Loose connection.
Replace PCB
assembly.
assembly.
Connect them
tightly.
tightly.
No continuity
Abnormal
Check fan motor.
Defective fan motor.
Replace fan motor.
Abnormal
Normal
Check oven lamp.
Defective oven lamp.
Replace oven lamp.
Defective
secondary switch.
secondary switch.
Replace
secondary switch.
secondary switch.
Check continuity
of secondary
switch (with
door closed).
of secondary
switch (with
door closed).
Check the con-
nection between
CN1 connector
and PCB
assembly.
nection between
CN1 connector
and PCB
assembly.
(TROUBLE 3) Display shows all figures set, but oven does not start cooking while desired
program times are set and START pad is touched.
(TROUBLE 4) Oven seems to be operating but little heat is produced in oven load.
NOTE : Simple test of power output-conducted by heating one liter water for one min. if available.
Minimum 8.5°C temperature rise is normal condition.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
Output is low
Lower than 90% of
rating voltage.
rating voltage.
Normal
Abnormal
Defective PCB
assembly.
assembly.
Replace PCB
assembly.
assembly.
Normal
Abnormal
Measure the
output power.
output power.
Defective
magnetron.
magnetron.
Replace
magnetron.
magnetron.
Decrease in power
source voltage
with load.
source voltage
with load.
Suggest customer
contact local
electric power
utility co. or
qualified
electrician.
contact local
electric power
utility co. or
qualified
electrician.
Check the
power source
voltage.
power source
voltage.
Disconnect the
wire leads from
relay 2 and
check on and off
time with
multitester.
wire leads from
relay 2 and
check on and off
time with
multitester.
5-15
CONDITION
CHECK
RESULT
CAUSE
REMEDY
No microwave
oscillation.
oscillation.
No continuity.
Continuity.
Abnormal
Defective high
voltage
transformer.
voltage
transformer.
Replace high
voltage
transformer.
voltage
transformer.
Normal
Defective PCB
assembly.
assembly.
Replace PCB
assembly.
assembly.
Disconnect the
wire leads from
relay 2 and
check continuity
of relay 2.
(Operate the unit)
wire leads from
relay 2 and
check continuity
of relay 2.
(Operate the unit)
Check high vol-
tage transformer.
tage transformer.
Abnormal
Defective circuit
protector.
protector.
Replace circuit
protector.
protector.
Normal
Check circuit
protector.
protector.
Abnormal
Defective high
voltage capacitor.
voltage capacitor.
Replace high
voltage capacitor.
voltage capacitor.
Normal
Check high vol-
tage capacitor.
tage capacitor.
Abnormal
Defective high
voltage diode.
voltage diode.
Replace high
voltage diode.
voltage diode.
Normal
Check high vol-
tage diode.
tage diode.
Abnormal
Defective
magnetron.
magnetron.
Replace
magnetron.
magnetron.
Check
magnetron.
magnetron.
(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.
(Display operates properly)
5-16
Output is full power
when you set lower
power level.
when you set lower
power level.
Abnormal.
Defective PCB
assembly.
assembly.
Replace PCB
assembly.
assembly.
Disconnect the
wire leads from
relay 2 and check
continuity relay 2.
(Operate the unit)
wire leads from
relay 2 and check
continuity relay 2.
(Operate the unit)
NOTE : • Make sure the wire leads correct position.
• When Removing the wire leads from the parts, be sure to grasp the connector, not the wires.
• When removing the magnetron, be sure to install the magnetron gasket in the correct position
• When removing the magnetron, be sure to install the magnetron gasket in the correct position
and in good condition.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.
(Display operates properly)
MEASUREMENT WITH OUTER CASE
REMOVED
REMOVED
• When you replace the magnetron, measure for
microwave energy leakage before the outer case is
installed and after all necessary components are
replaced or adjusted.
installed and after all necessary components are
replaced or adjusted.
Special care should be taken in measuring the
following parts. (Circled area of below Fig.)
- Around the magnetron
- The waveguide
- The waveguide
MEASUREMENT WITH A FULLY
ASSEMBLED OVEN
ASSEMBLED OVEN
• After all components, including the outer case, are fully
assembled, measure for microwave energy leakage
around the door viewing window, the exhaust opening,
and air inlet openings.
around the door viewing window, the exhaust opening,
and air inlet openings.
• Microwave energy leakage must not exceed the values
prescribed below.
NOTE: Leakage with the outer case removedless than
5 mW/cm.sq. Leakage for a fully assembled
oven (Before the latch switch (primary) is
interrupted) with the door in a slightly opened
position-less than 2 mW/cm.sq.
oven (Before the latch switch (primary) is
interrupted) with the door in a slightly opened
position-less than 2 mW/cm.sq.
NOTES WHEN MEASURING
• Do not exceed meter full scale deflection.
• The test probe must be removed no faster than
• The test probe must be removed no faster than
1 inch/sec (2.5 cm/sec) along the shaded area,
otherwise a false reading may result.
otherwise a false reading may result.
• The test probe must be held with the grip portion of the
handle.
A false reading may result if the operator's hand is
between the handle and the probe.
• When testing near a corner of the door, keep the probe
perpendicular to the surface making sure the probe
horizontally along the oven surface, this may possibly
cause probe damage.
horizontally along the oven surface, this may possibly
cause probe damage.
RECORD KEEPING AND NOTIFICATION
AFTER MEASUREMENT
AFTER MEASUREMENT
• After adjustment and repair of any microwave energy
interruption or microwave energy blocking device,
record the measured values for future reference. Also
enter the information on the service invoice.
record the measured values for future reference. Also
enter the information on the service invoice.
• The microwave energy leakage should not be more
than 4 mW/cm.sq. after determining that all parts are in
good condition, functioning properly and genuine
replacement parts which are listed in this manual have
been used.
good condition, functioning properly and genuine
replacement parts which are listed in this manual have
been used.
• At least once a year, have the electromagnetic energy
leakage monitor checked for calibration by its
manufacturer.
manufacturer.
5-2
WARNING : AVOID CONTACTING ANY
HIGH VOLTAGE PARTS
(Magnetron, H.V. Transformer,
H.V. Capacitor, H.V. Cable Ass’y,
H.V. Circuit Protector)
H.V. Capacitor, H.V. Cable Ass’y,
H.V. Circuit Protector)
Click on the first or last page to see other MS-2042W service manuals if exist.