LG LWC0961AHG Service Manual ▷ View online
—25—
COMPLAINT
CAUSE
REMEDY
If cracked, out of balance, or partially missing,
replace it.
replace it.
If cracked, out of balance, or partially missing,
replace it.
replace it.
Tighten it.
If knocking sounds continue when running or
loose, replace the motor. If the motor hums or
noise appears to be internal while running,
replace motor.
loose, replace the motor. If the motor hums or
noise appears to be internal while running,
replace motor.
Check voltage. See the limits on the preceeding
page. If not within limits, call an electrician.
page. If not within limits, call an electrician.
Check the wire connections, if loose, repair or
replace the terminal. If wires are off, refer to wiring
diagram for identification, and replace. Check wire
locations. If not per wiring diagram, correct.
replace the terminal. If wires are off, refer to wiring
diagram for identification, and replace. Check wire
locations. If not per wiring diagram, correct.
Check for continuity, refer to the wiring diagram
for terminal identification. Replace the switch if
circuit is open.
for terminal identification. Replace the switch if
circuit is open.
Check the position of knob If not at the coldest
setting, advance the knob to this setting and
restart unit.
Check continuity of the thermostat. Replace
thermostat if circuit is open.
setting, advance the knob to this setting and
restart unit.
Check continuity of the thermostat. Replace
thermostat if circuit is open.
Check the capacitor.
Replace if not within ±10% of manufacturers
rating. Replace if shorted, open, or damaged.
Replace if not within ±10% of manufacturers
rating. Replace if shorted, open, or damaged.
Check the compressor for open circuit or ground.
If open or grounded, replace the compressor.
If open or grounded, replace the compressor.
Check the compressor overload, if externally
mounted. Replace if open. (If the compressor
temperature is high, remove the overload, cool it,
and retest.)
mounted. Replace if open. (If the compressor
temperature is high, remove the overload, cool it,
and retest.)
Check the voltage.
If not within limits, call an electrician.
If not within limits, call an electrician.
Check overload, if externally mounted.
Replace if open. (If the compressor temperature
is high, remove the overload, cool, and retest.)
Replace if open. (If the compressor temperature
is high, remove the overload, cool, and retest.)
Check the system for a restriction.
Fan
Blower
Loose clamper
Worn bearings
Voltage
Wiring
Rotary
Thermostat
Capacitor (Discharge
capacitor before servicing.)
capacitor before servicing.)
Compressor
Overload
Voltage
Overload
Refrigerating system
Fan motor noise.
Compressor will not run,
but fan motor runs.
but fan motor runs.
Compressor cycles on
overload.
overload.
—27—
■
MODEL : LWC0961AHG/ABG
MOTOR
COMP.
1
2
4
6
8
7
H
L
C
F
C
C
H
L3
L2
L1
DEICER PWB ASSY
BK(BR)
(Plain)
WH(BL)
(Ribbed)
WH
WH
BL
BL
BL
BL
BL
RD
RD
BK
BK
BK
BK
BK
BK
BK(RD)
BK(RD)
BK
BK
BL
RD
RD
RD
YL
YL
YL
YL
OR
OR
OR
OR
R/SWITCH
BR
BR
O.L.P.
T/B 2
THERMISTOR
THERMOST
A
T
BL
BK
BK
LAMP
BK
BR
T/B 1
CAPACITOR
REVERSING COIL
WIRING DIAGRAM
3854A20022M
MOTOR
RD
BK
BL
BK
RD
BL
BL
OR(BR)
BK
RD
OR(BR)
YL
F
C
H
CAPACITOR
R
C
COMP.
TRANS-
FORMER
FORMER
S
RD
THERMISTOR
BK
OR(BR)
BK(BR)
POWER INPUT
(Plain)
CN-TH
RY-HI
CN-DISP
DISPLAY
P.W.B ASSY
RY-COMP
ZNR
MAIN P.W.B ASSY
RY-4WAY
CN-4WAY
BK(RD)
BK(RD)
BK
T/B 1
T/B 2
BK
SUMP
HEATER
HEATER
BK
BK
RD
RD
RD
RD
REVERSING COIL
4
3
RY-LO
GN/YL(GN)
WH(BL)
(Ribbed)
YL
BR
BR
SYNC.
MOTOR
CN-
SYNC
RY-SYNC
GN/YL
(GN)
FUSE
250V/T2A
(115V/T2A)
OLP
■
MODEL : LWC0961PHG/PBG
5. SCHEMATIC DIAGRAM
5.1 CIRCUIT DIAGRAM
—28—
5.2 DEICER P.C.B. ASSY
■
MODEL : LWC0961AHG/ABG
—29—
5.3 ELECTRONIC CONTROL DEVICE
■
MODEL : LWC0961PHG/PBG
Click on the first or last page to see other LWC0961AHG service manuals if exist.