DOWNLOAD LG LWC0961AHG Service Manual ↓ Size: 3.4 MB | Pages: 63 in PDF or view online for FREE

—6—

1. Open the lnlet grille upward .
2. Remove the screw which fastens the front grille.
3. Pull the front grille from the right side.
4. Remove the front grille.
5. Re-install the component by referring to the

removal procedure, above.(See Figure 1)

1. After disassembling the FRONT GRILLE, remove

the 2 screws which fasten the cabinet at both
sides.

2. Remove the 2 screws which fasten the cabinet at

back.

3. Pull the base pan forward. (See Figure 2)
4. Remove the cabinet.
5. Re-install the component by referring to the

removal procedure, above.

1. Remove the front grille. (Refer to section 2.1.1)
2. Remove the cabinet. (Refer to section 2.1.2)
3. Remove the 2 screws which fasten the control box

cover.

4. Remove two  housings which connect compressor

wire and motor wire in the control box.

5.Discharge the capacitor by placing a 20,000

ohmresistor across the capacitor terminals.

6. Remove the 2 screws which fasten the control

box.

7. Pull the control box forward completely.
8. Re-install the components by referring to the

removal procedure, above. (See Figure 3)
(Refer to the circuit diagram found on pages
24~25 in this manual and on the control box.)

Warm

er

Cooler

Warmer

Cooler

Warm

er

Coole

r

— Before the following disassembly, POWER SWITCH set to OFF and disconnect the power cord.

—7—

1. Remove the front grille. (Refer to section 2.1.1)

2. Remove the cabinet. (Refer to section 2.1.2)

3. Remove the control box. (Refer to section 2.1.3)

4. Remove the 4 screws which fasten the brace.

5. Remove the brace.

6. Remove the 2 screws which fasten the evaporator.

7. Move the evaporator forward and pulling it upward

slightly. (See Figure 4)

8. Move the evaporator to the left carefully. 

9. Pull out the hook of orifice by pushing the tabs and

remove it. (See Figure 5)

10. Remove the clamp with a hand plier which

secures the blower.

11. Remove the blower.
12. Remove the 4 screws which fasten the air guide

from the barrier.

13. Move the air guide backward, pulling out from the

base pan.

14. Re-install the components by referring to the

removal procedure, above. 

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the brace (Refer to section 2.2.1)

3. Remove the 4 screws which fasten the condenser.

4. Move the condenser to the left carefully.

5. Remove the clamp which secures the fan.

6. Remove the fan. (See Figure 7)

7. Re-install by referring to the removal procedure. 

Warm

er

Cooler

—8—

1. Remove the fan. (Refer to section 2.2.2)
2. Remove the screw which fastens the shroud.

3. Remove the shroud. (See Figure 8)

4. Re-install the component by referring to the

removal procedure, above.

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the nut which fastens the terminal cover.

3. Remove the terminal cover. (See Figure 9)

4. Remove all the leads from the overload protector.

5. Remove the overload protector.

6. Re-install the component by referring to the

removal procedure, above. 

1. Remove the cabinet. (Refer to section 2.1.2)

2. Discharge the refrigerant system using a Freon

TM

Recovery System.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before venting
the Freon

TM

. Leave the valve in place after 

servicing the system.

3. Remove the overload protector. (Refer to section

2.3.1)

4. After purging the unit completely, unbraze the

suction and discharge tubes at the compressor
connections.

5. Remove the 3 nuts and the 3 washers which 

fasten the compressor.

6. Remove the compressor. (See Figure 10)

7. Re-install the components by referring to the

removal procedure, above.

—9—

1. Remove the control box. (Refer to section 2.1.3)
2. Remove the knobs and the screw which fasten

control panel from control box.

3. Remove the screw which located in the front.
4. Open the bottom side of control box.
5. Remove the screw and the clamp which fastens

the capacitor.

6. Disconnect all the leads of capacitor terminals.
7. Re-install the components by referring to the

removal procedure, above. (See Figure 11)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Disconnect the grounding screw from the control

box.

4. Disconnect the 2 receptacles.
5. Remove a screw which fastens the clip cord. 

(See Figure 12)

6. Remove the power cord. 
7. Re-install the component by referring to the above

removal procedure, above.
(Use only one ground-marked hole      for ground
connection.)

8. If the supply cord of this appliance is damaged, it

must be replaced by the special cord. (The 
special cord means the cord which has the same
specification marked on the supply cord attached
at the unit.)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Remove the 2 screws which fasten the thermostat.
4. Disconnect 2 leads of thermostat terminals.
5. Remove the thermostat.
6. Re-install the components by refereing to the

above removal procedure. (See Figure 13)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Remove the 2 screws which fasten the rotary

switch.

4. Disconnect all the leads of the rotary switch

terminals.

5. Remove the rotary switch.
6. Re-install the components by referring to the

above removal procedure. (See Figure 14)