LG LS-M3061HL Service Manual ▷ View online
- 41 -
➎
Remove the grille from the chassis.
• Remove the 4 securing screws.(30K, 32K)
• Remove the 5 securing screws.(36K, 38K)
• To remove the Grille, pull the lower left and right side
• Remove the 5 securing screws.(36K, 38K)
• To remove the Grille, pull the lower left and right side
of the grille toward you (slightly tilted) and lift it
straight upward.
straight upward.
2. To remove the sensor, housing connector, earth
conductor and step motor conductor with sensor
holder, Motor, Evaporator and P.C.B.
holder, Motor, Evaporator and P.C.B.
Power
Conductor
Conductor
Step Motor
Conductor
Conductor
Motor
Conductor
Conductor
Sensor
Conductor
Conductor
Earth
Conductor
Conductor
30K, 32K
36K, 38K
30K, 32K
36K, 38K
- 42 -
3. To remove the Control Box.
• Remove the 5 securing screws.
• Pull the control box out from the chassis carefully.
• Pull the control box out from the chassis carefully.
4. To remove the Discharge Grille.
• Remove the 3 securing screw.
• Pressing the right side of the discharge grille
• Pressing the right side of the discharge grille
downward slightly, unhook the discharge grille.
• Pull the discharge grille out from the chassis
carefully.
5. To remove the Evaporator.
• Remove 3 screws securing the evaporator(at the
left 2EA, at the right 1EA).
• Remove 2 screws securing the evaporator clamp.
• Unhook the tab on the right inside of the chassis
at the same time, slightly pull the evaporator
toward you until the tab is clear of the slot.
toward you until the tab is clear of the slot.
Screw
Screw
(for clamp)
Screw
Screw
- 43 -
6. To remove the Fan motor
• Loosen the screw securing the cross-flow fan to
the fan motor (do not remove).
• Loosen the screw securing the mount motor.
• Separate the fan motor from the cross-flow fan.
• Take care not to drop the motor.
• Take care not to drop the motor.
7. To remove the Cross-Flow Fan
• Loosen the screw securing the holder bearing.
• Lift up the cross-flow fan.
• Lift up the cross-flow fan.
Screw
Fan motor
Screw
Screw
Fan motor
Mount motor
Holder bearing
- 44 -
Warning :
Disconnect the unit from power supply before making
any checks.
Be sure the power switch is set to “OFF”.
Disconnect the unit from power supply before making
any checks.
Be sure the power switch is set to “OFF”.
1. To remove the Grille from the Chassis.
➊
Remove the 2 screws of right side panel.
➋
Remove the right side panel by the arrow.
■
The connector can be disconnected by pulling it
while pressing the connector's hook.
while pressing the connector's hook.
■
Remove the 1 screw for fixing low panel.
➌
Remove the lower panel by the arrow.
■
Take care not to scratch the wall and mat to
drop.
drop.
➍
Remove the left side panel.
(Remove the 2 screws.)
(Remove the 2 screws.)
■
LS-M3060HL/CL, LS-M3061HL/CL, LS-M3064HL/CL, LS-M3221HL/CL
LS-N3660HL/CL, LS-N3661HL/CL, LS-N3821HL/CL
LS-N3660HL/CL, LS-N3661HL/CL, LS-N3821HL/CL
Right side panel
Main PCB
Lower panel
Left side panel
Lower panel
Click on the first or last page to see other LS-M3061HL service manuals if exist.