DOWNLOAD LG LS-J0763EL Service Manual ↓ Size: 4.3 MB | Pages: 127 in PDF or view online for FREE

-35-

• Capicity is based on standard length and maximum allowance length is the basis of reliability.

• Oil trap should be installed per 5~7 meters.

• Numerical value in "(    )" is for Rotary Comp. model.

Max. Piping

Length

Ⓐ

(m)

Capacity

(Btu/h)

7~12K

15

7

5

20

Max. 

Elevation 

Ⓑ

(m)

Standard

Length(m)

Additional Refrig-

erant

(g/m)

-36-

Discharge air

Bolt

Tubing

connection

Battery Cover

• Anchor the outdoor unit with a bolt and nut

(ø10cm) tightly and horizontally on a concrete or
rigid mount.

• When installing on the wall, roof or rooftop, anchor

the mounting base securely with a nail or wire
assuming the influence of wind and earthquake.

• In the case when the vibration of the unit is con-

veyed to the house, settle the unit with an anti-
vibration rubber.

pendent power supply.
• Circuitbreaker is required.

• Insert two batteries provided.

Remove the battery cover from the remote con-
troller.

• Slide the cover according to the arrow direction.

Insert two batteries.
(Two "R03" or "AAA" dry-cell batteries or equiv-
alent.)

• Be sure that the (+) and (-) directions are cor-

rect.

• Be sure that both batteries are new.

Re-attach the cover.

• Slide it back into position.

-22-

5-7mm

Indoor

Outdoor

WALL

Right rear piping

Installation plate

Marking-off line

Thread

Weight

Type "A" screw

Left rear piping

ø70mm

ø70mm

80mm

50mm

40mm

40mm

ø70mm

ø70mm

80mm

50mm

40mm

40mm

The mounting wall should be strong and solid enough
to protect it from the vibration.

(if mounting the unit on the concrete wall, consider
using anchor bolts.)

• Always mount the Installation plate horizontally by

aligning the marking-off line by means of the
thread and a level.

• Line according to the arrows marked on lower the

left and the right side of the Installation Plate.
The meeting point of the extended line is the cen-
ter of the hole.

• Drill the Piping hole at either the right or the left

and the hole should be slightly slanted to the out-
door side.

-23-

• Use the accessory piping kit or the pipes pur-

chased locally.

• Measure the distance between the indoor and the

outdoor unit.

• Cut the pipes a little longer than measured dis-

tance.

• Cut the cable 1.5m longer than the length of the

pipe.

• Remove burrs from cut edges of pipes.

• Turn the pipe end toward down to avoid the metal

powder entering the pipe.

Caution:
If burrs are not removed, they may cause a gas leak-
age.

• Insert the flare nuts, mounted on the connection

ports of both indoor and outdoor unit, onto the
copper pipes. (When the flare nuts are removed
from the indoor unit.) Some gas may leak, as
some gas is charged to prevent the inside of the
pipe from rusting.

• Fit the copper pipe end into the Bar of flare tool

about 0~1.0mm higher. (See illustration)

• Flare the pipe ends.

90

Slanted Rough

Pipe cutter

Pipe

Reamer

Point down

"A"

Bar

Bar

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Copper pipe

Inclined

Cracked

Uneven

thickness

Surface

damaged

= Improper flaring =

When properly flared, the internal surface of the flare will
evenly shine and be of even thickness.
After the flare part comes into contact with the connec-
tors, carefully check the flare finish.

"A"; ø15.88 mm (5/8") 

→0~

1.0 mm

ø12.7 mm (1/2") 

→ 0~

0.5 mm

ø9.52 mm (3/8") 

→ 0~

0.5 mm

ø6.35 mm (1/4") 

→ 0~

0.5 mm