LG AS-C0764DM0 / AS-H0764DM0 / LS-C1264DM0 / LS-H0764DM0 / AS-C0964DM0 / AS-H0964DM0 / LS-C1865DM0 / LS-H0964DL0 / AS-C1264DM0 / AS-H1264DM0 / LS-C2665DM0 / LS-H1264DM0 / AS-C1865DM0 / AS-H1865DM0 / LS-C0964DA0 / LS-H1865DM0 / AS-C2465DM0 / AS-H2465DM0 / LS-C0964DM0 / LS-H2665DM0 / AS-C0764DB0 / AS-H0764GM0 / LS-C1865DB0 / LS-H2465DM0 / AS-C0964DB0 / AS-H0964GM0 / LS-C1264DA0 / LS-H0964DM0 / AS-C1264DB0 / AS-H1264GM0 / LS-C2465DB0 / AS-C1865DB0 / AS-H1865GM0 / LS-C2465GB0 / AS-C2465DB0 / AS-H2465GM0 / LS-C1865DM1 / LS-C1865GB0 / LS-C2665DM1 / AS-C0764DH0 / AS-C0964DH0 / AS-C1264DH0 / AS-C1865DH0 / AS-C2465DH0 / AS-C0964DA0 / AS-C1264DA0 / AS-C0964GA0 / AS-C1264GA0 / AS-C1865GB0 / AS-C2465GB0 / AS-H0964DA0 / AS-H1264DA0 / AS-H1865DB0 / LS-C1264DM1 / AS-H2465DB0 / LS-C1264GA0 / AS-H0964GA0 / LS-C1264GB0 / AS-H1264GA0 / LS-C0964DM1 / AS-H1865GB0 / AS-H2465GB0 / AS-H2465DM1 / LS-H0964DY0 / LS-H1264DY0 / LS-H1865DY0 / LS-H2465DY0 / LS-H0764DM1 / LS-H0964DM1 / LS-H1264DM1 / LS-H1865DM1 / LS-H2465DM1 / LS-H2665DM1 / LS-H2465GB0 / LS-H0964GB0 / LS-H1264GB0 Service Manual ▷ View online
installation plate until the hooks engage into their
slots(clicking sound).
into the rear piping housing section.
the back of the chassis.
of the chassis with the tubing holder.
chassis.
pipe
unit piping
(wide)
vinyl tape(wide)
passage through
piping hole
tighten the flare nut by hand.
until the wrench clicks.
(Bigger diameter)
piping
(Smaller
diameter)
those of the indoor unit.). The earth wire should be longer than the common wires.
The above circuit diagram is subject to change without notice.
When installing, refer to the circuit diagram on the control box
inside Indoor Uint.
Use a circuit
breaker or time
delay fuse.
the indoor and outdoor unit should be
complied with the following specifications
(Type "B" approved by HAR or SAA).
should be complied with the following
specifications(Type "B" approved by HAR or
SAA).
CROSS-SECTIONAL
AREA 0.75mm
shown below.
loosening the screw.
trol board individually.
the cord clamp.
with the screw.
between the power source and the unit.
A disconnecting device to adequately discon-
nect all supply lines must be fitted.
1) Never fail to have an individual power circuit specifically for the air conditioner. As for the method of wiring,
all tightly fastened. (If they are loose, it could cause burn-out of the wires.)
4) Confirm that electrical capacity is sufficient.
5) See to that the starting voltage is maintained at more than 90 percent of the rated voltage marked on the
8) The following would be caused by voltage drop.
Click on the first or last page to see other AS-C0764DM0 / AS-H0764DM0 / LS-C1264DM0 / LS-H0764DM0 / AS-C0964DM0 / AS-H0964DM0 / LS-C1865DM0 / LS-H0964DL0 / AS-C1264DM0 / AS-H1264DM0 / LS-C2665DM0 / LS-H1264DM0 / AS-C1865DM0 / AS-H1865DM0 / LS-C0964DA0 / LS-H1865DM0 / AS-C2465DM0 / AS-H2465DM0 / LS-C0964DM0 / LS-H2665DM0 / AS-C0764DB0 / AS-H0764GM0 / LS-C1865DB0 / LS-H2465DM0 / AS-C0964DB0 / AS-H0964GM0 / LS-C1264DA0 / LS-H0964DM0 / AS-C1264DB0 / AS-H1264GM0 / LS-C2465DB0 / AS-C1865DB0 / AS-H1865GM0 / LS-C2465GB0 / AS-C2465DB0 / AS-H2465GM0 / LS-C1865DM1 / LS-C1865GB0 / LS-C2665DM1 / AS-C0764DH0 / AS-C0964DH0 / AS-C1264DH0 / AS-C1865DH0 / AS-C2465DH0 / AS-C0964DA0 / AS-C1264DA0 / AS-C0964GA0 / AS-C1264GA0 / AS-C1865GB0 / AS-C2465GB0 / AS-H0964DA0 / AS-H1264DA0 / AS-H1865DB0 / LS-C1264DM1 / AS-H2465DB0 / LS-C1264GA0 / AS-H0964GA0 / LS-C1264GB0 / AS-H1264GA0 / LS-C0964DM1 / AS-H1865GB0 / AS-H2465GB0 / AS-H2465DM1 / LS-H0964DY0 / LS-H1264DY0 / LS-H1865DY0 / LS-H2465DY0 / LS-H0764DM1 / LS-H0964DM1 / LS-H1264DM1 / LS-H1865DM1 / LS-H2465DM1 / LS-H2665DM1 / LS-H2465GB0 / LS-H0964GB0 / LS-H1264GB0 service manuals if exist.