JBL SPARK (serv.man5) EMC - CB Certificate ▷ View online
Report No.: EM201300221-5 Application No.: ZJ00028648 Page 37 of 68
FCC ID:
APISPARK
3DH1
3DH3
Report No.: EM201300221-5 Application No.: ZJ00028648 Page 38 of 68
FCC ID:
APISPARK
3DH5
Report No.: EM201300221-5 Application No.: ZJ00028648 Page 39 of 68
FCC ID:
APISPARK
4.7 CONDUCTED EMISSION MEASUREMENT
4.7.1 LIMITS
Frequency range
Limits (dBµV)
Quasi-peak
Average
150kHz ~ 0.5MHz
66~56 56~46
0.5 MHz ~ 5 MHz
56 46
5 MHz ~ 30 MHz
60 50
4.7.2 TEST PROCEDURES
Procedure of Preliminary Test
For measurement of the disturbance voltage the equipment under test (EUT) is connected to
the power supply mains and any other extended network via one or more artificial
network(s). An EUT, whether intended to be grounded or not, and which is to be used on a
table is configured as follows:
the power supply mains and any other extended network via one or more artificial
network(s). An EUT, whether intended to be grounded or not, and which is to be used on a
table is configured as follows:
– Either the bottom or the rear of the EUT shall be at a controlled distance of 40 cm from a
reference ground plane. This ground plane is normally the wall or floor of a shielded room. It
may also be a grounded metal plane of at least 2 m by 2 m. This is physically accomplished
as follows:
reference ground plane. This ground plane is normally the wall or floor of a shielded room. It
may also be a grounded metal plane of at least 2 m by 2 m. This is physically accomplished
as follows:
1) place the EUT on a table of non-conducting material which is at least 80 cm high. Place
the EUT so that it is 40 cm from the wall of the shielded room, or
the EUT so that it is 40 cm from the wall of the shielded room, or
2) place the EUT on a table of non-conducting material which is 40 cm high so that the
bottom of the EUT is 40 cm above the ground plane;
bottom of the EUT is 40 cm above the ground plane;
– All other conductive surfaces of the EUT shall be at least 80 cm from the reference
ground plane;
ground plane;
– The EUT are placed on the floor that one side of the housings is 40 cm from the vertical
reference ground plane and other metallic parts;
reference ground plane and other metallic parts;
– Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded
back and forth forming a bundle 30 cm to 40 cm long, hanging approximately in the middle
between the ground plane and the table.
back and forth forming a bundle 30 cm to 40 cm long, hanging approximately in the middle
between the ground plane and the table.
– I/O cables that are connected to a peripheral shall be bundled in the centre. The end of the
cable may be terminated if required using correct terminating impedance. The total length
shall not exceed 1 m.
cable may be terminated if required using correct terminating impedance. The total length
shall not exceed 1 m.
The test mode(s) described in Item 2.4 were scanned during the preliminary test. After the
preliminary scan, we found the test mode described in Item 2.4 producing the highest
emission level. The EUT configuration and cable configuration of the above highest
emission levels were recorded for reference of the final test.
preliminary scan, we found the test mode described in Item 2.4 producing the highest
emission level. The EUT configuration and cable configuration of the above highest
emission levels were recorded for reference of the final test.
Procedure of Final Test
EUT and support equipment were set up on the test bench as per the configuration with
highest emission level in the preliminary test. A scan was taken on both power lines,
recording at least the six highest emissions. Emission frequency and amplitude were
recorded into a computer in which correction factors were used to calculate the emission
level and compare reading to the applicable limit. The test data of the worst-case
condition(s) was recorded.
EUT and support equipment were set up on the test bench as per the configuration with
highest emission level in the preliminary test. A scan was taken on both power lines,
recording at least the six highest emissions. Emission frequency and amplitude were
recorded into a computer in which correction factors were used to calculate the emission
level and compare reading to the applicable limit. The test data of the worst-case
condition(s) was recorded.
Report No.: EM201300221-5 Application No.: ZJ00028648 Page 40 of 68
FCC ID:
APISPARK
4.7.3 TEST SETUP
Click on the first or last page to see other SPARK (serv.man5) service manuals if exist.