JBL ON STAGEII (serv.man12) EMC - CB Certificate ▷ View online
IEC 60950 3
rd
Ed, 1999
- Page 1 of 1 -
Order No. 46974
APPENDIX: ISRAEL DEVIATIONS
Test results according to SI 60950 : 2000
Variations to IEC 60950:1999 for application in Israel.
Clause
Requirement - Test
Result - Remark
Ver-
dict
1.2.12.1
TN Power Distribution
The mains system in Israel in TN-S or TN-C or
TN-C-S.
The mains system in Israel in TN-S or TN-C or
TN-C-S.
Class III equipment.
N/A
1.7 Marking
and
Instructions
The package of the equipment shall be marked
in Hebrew, and shall include:
in Hebrew, and shall include:
The name of the manufacturer,
The name of the product,
The country and year of production,
The name and address of the importer.
The marking shall be on a rectangular label (of
at least 52mm x 24mm). The letters height
should be at least 2mm. The color of the label
shall be in contrast to the color of the package.
at least 52mm x 24mm). The letters height
should be at least 2mm. The color of the label
shall be in contrast to the color of the package.
Must be considered before
marketing in Israel.
marketing in Israel.
—
1.7.12 Language
All instructions and warnings concerning safety
should be in the Hebrew language.
should be in the Hebrew language.
Must be considered before
marketing in Israel.
marketing in Israel.
—
2.101 EMC
The equipment shall comply with SI 961 part 6
(CISPR 22 + 24).
(CISPR 22 + 24).
Must be considered before
marketing in Israel.
marketing in Israel.
—
3.2.1.1
Connection to an a.c. mains supply
Additional note :
In Israel the mains supply plug shall comply
with the Israeli standard SI 32.
Additional note :
In Israel the mains supply plug shall comply
with the Israeli standard SI 32.
Class III equipment.
N/A
3.2.3 Permanently
connected
equipment
Additional note below table 3A:
In Israel the diameter of the conduit
shall comply with the Electricity Law.
Class III equipment, not for
permanently connected to the
mains.
permanently connected to the
mains.
N/A
IEC 60950 3rd Ed., 1999.
- Page 1 of 5 -
Order No. 46974
APPENDIX: JAPAN DEVIATIONS
Test results according to CB BULLETIN No. 107A, May 2004
Clause
Requirement - Test
Result - Remark
Ver-
dict
1.2
Addition:
Add the following terms.
Add the following terms.
Equipment, Class 0I
1.2.4.101
Material, VTM
1.2.12.101
Considered. —
1.2.4.101
Addition:
CLASS 0I EQUIPMENT: Equipment where protection
against electric shock is achieved by:
CLASS 0I EQUIPMENT: Equipment where protection
against electric shock is achieved by:
a) using BASIC INSULATION, and
b) providing a means of connecting to the protective
earthing conductor in the building wiring those
conductive parts that are otherwise capable of
assuming HAZARDOUS VOLTAGES if the BASIC
INSULATION fails, and
earthing conductor in the building wiring those
conductive parts that are otherwise capable of
assuming HAZARDOUS VOLTAGES if the BASIC
INSULATION fails, and
c) using a supply cord without earthing conductor and
a plug without earthing wire although the equipment
has externally an earth terminal or a lead wire for
earthing.
a plug without earthing wire although the equipment
has externally an earth terminal or a lead wire for
earthing.
Equipment provided with a cord set having a two-pin
type plug with a lead wire for earthing is also regarded
as Class 0I.
type plug with a lead wire for earthing is also regarded
as Class 0I.
NOTE – Class 0I equipment may have a part
constructed with Double Insulation or Reinforced
Insulation as well as an operating part as SELV circuit.
constructed with Double Insulation or Reinforced
Insulation as well as an operating part as SELV circuit.
Class III equipment.
N/A
1.2.12.1
Replacement:
FLAMMABILITY CLASSIFICATION OF MATERIALS:
The recognition of the burning behaviour of materials
and their ability to extinguish if ignited. Materials are
classified as in 1.2.12.2 to 1.2.12.9, and 1.2.12.101
when tested in accordance with annex A.
FLAMMABILITY CLASSIFICATION OF MATERIALS:
The recognition of the burning behaviour of materials
and their ability to extinguish if ignited. Materials are
classified as in 1.2.12.2 to 1.2.12.9, and 1.2.12.101
when tested in accordance with annex A.
NOTE 1 - When applying the requirements in this
standard, HF-1 CLASS FOAMED MATERIALS are
regarded as better than those of CLASS HF-2, and
HF-2 better than HBF.
standard, HF-1 CLASS FOAMED MATERIALS are
regarded as better than those of CLASS HF-2, and
HF-2 better than HBF.
NOTE 2 - Similarly, other MATERIALS, including rigid
(engineering structural) foam of CLASSES 5V or V-0
are regarded as better than those of CLASS V-1, V-1
better than V-2, and V-2 better than HB.
(engineering structural) foam of CLASSES 5V or V-0
are regarded as better than those of CLASS V-1, V-1
better than V-2, and V-2 better than HB.
NOTE 3 - Similarly, for thin MATERIALS, VTM-0 Class
materials are regarded as better than those of VTM-1
Class, and VTM-1 better than VTM-2.
materials are regarded as better than those of VTM-1
Class, and VTM-1 better than VTM-2.
Considered, refer to List of
Critical Componets in main
test report.
Critical Componets in main
test report.
P
IEC 60950 3rd Ed., 1999.
- Page 2 of 5 -
Order No. 46974
Clause
Requirement - Test
Result - Remark
Ver-
dict
1.2.12.101
Addition:
VTM CLASS MATERIAL: Thin MATERIALS fulfil the
specified conditions during the test of clause A.101
applied for materials that the test and evaluation of
clauses A.6 to A.10 is difficult to enforce. Materials are
classified to three classifications as VTM-0, VTM-1 and
VTM-2 according to the conditions after the removal of
the test flame.
VTM CLASS MATERIAL: Thin MATERIALS fulfil the
specified conditions during the test of clause A.101
applied for materials that the test and evaluation of
clauses A.6 to A.10 is difficult to enforce. Materials are
classified to three classifications as VTM-0, VTM-1 and
VTM-2 according to the conditions after the removal of
the test flame.
Considered. N/A
1.7.101
Addition:
Marking for CLASS 0I EQUIPMENT
Marking for CLASS 0I EQUIPMENT
For CLASS 0I EQUIPMENT, the following instruction
shall be indicated on the visible place of the mains plug
or the main body:
shall be indicated on the visible place of the mains plug
or the main body:
“Provide an earthing connection”
Moreover, for CLASS 0I EQUIPMENT, the following
instruction shall be indicated on the visible place of the
main body or written in the operating instructions:
instruction shall be indicated on the visible place of the
main body or written in the operating instructions:
“Provide an earthing connection before the mains plug
is connected to the mains. And, when disconnecting
the earthing connection, be sure to disconnect after
pulling out the mains plug from the mains.”
is connected to the mains. And, when disconnecting
the earthing connection, be sure to disconnect after
pulling out the mains plug from the mains.”
Class III equipment.
N/A
2.1.1.1
Replacement:
Replace “IEC 60083” to “IEC 60083 or JIS C 8303” in
2.1.1.1 b).
Replace “IEC 60083” to “IEC 60083 or JIS C 8303” in
2.1.1.1 b).
Considered. —
2.6.3.1
Addition:
Add the following after 1st paragraph.
Add the following after 1st paragraph.
This also applies to the conductor of lead wire for
protective earthing of CLASS 0I EQUIPMENT.
protective earthing of CLASS 0I EQUIPMENT.
Class III equipment.
N/A
2.6.4.1
Replacement:
Replace 2nd sentence in 1st paragraph.
Replace 2nd sentence in 1st paragraph.
For CLASS I EQUIPMENT with a DETACHABLE
POWER SUPPLY CORD, the earthing terminal in the
appliance inlet is regarded as the main protective
earthing terminal.
POWER SUPPLY CORD, the earthing terminal in the
appliance inlet is regarded as the main protective
earthing terminal.
Class III equipment.
N/A
2.6.5.4
Replacement:
Replace 1st sentence.
Replace 1st sentence.
Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later than
the supply connections in each of the following:
EQUIPMENT shall make earlier and break later than
the supply connections in each of the following:
Class III equipment.
N/A
IEC 60950 3rd Ed., 1999.
- Page 3 of 5 -
Order No. 46974
Clause
Requirement - Test
Result - Remark
Ver-
dict
2.6.101
Addition:
Earthing of CLASS 0I EQUIPMENT
Earthing of CLASS 0I EQUIPMENT
Plugs with a lead wire for earthing shall not be used for
equipment having a rated voltage exceeding 150V.
equipment having a rated voltage exceeding 150V.
For plugs with a lead wire for earthing, the lead wire
shall not be earthed by a clip.
shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with an
earthing terminal or lead wire for earthing in the
external where easily visible.
earthing terminal or lead wire for earthing in the
external where easily visible.
Class III equipment.
N/A
3.2.5
Delete 1) in Table 3B.
Considered.
—
4.2.8
Addition:
Add the following informative remark after the last
sentence.
Add the following informative remark after the last
sentence.
Remark - IEC 61965 is also applicable instead of IEC
60065.
60065.
Considered. —
4.5.1
Addition:
Add the following to suffix 5) as specified in
“Conditions applicable to Table 4A, Parts 1 and 2”.
Add the following to suffix 5) as specified in
“Conditions applicable to Table 4A, Parts 1 and 2”.
With regard to Table 4A, insulating materials
complying with Japanese requirements (refer to
Japanese differences for the current IEC 60335-1 (3rd
Edition) in CB Bulletin 101B) are also acceptable.
complying with Japanese requirements (refer to
Japanese differences for the current IEC 60335-1 (3rd
Edition) in CB Bulletin 101B) are also acceptable.
Add a suffix 7) in “Conditions applicable to Table 4A,
Parts 1 and 2”.
Parts 1 and 2”.
In the right column of Table 4A, Part 1, add suffix 7) to
“50” (K), corresponding to “- without T – marking” in the
left column so as to become “50 7)”.
“50” (K), corresponding to “- without T – marking” in the
left column so as to become “50 7)”.
Add 7) to Table 4A, Part 2 as follows.
7) This value shall apply only to wiring or cords
complying with relevant IEC standards. Others shall
comply with Japanese requirements (refer to Japanese
differences for the current IEC 60335-1 (3rd Edition) in
CB Bulletin 101B).
complying with relevant IEC standards. Others shall
comply with Japanese requirements (refer to Japanese
differences for the current IEC 60335-1 (3rd Edition) in
CB Bulletin 101B).
Considered. N/A
4.7.3.2
Addition:
Add the following in 7th paragraph.
Add the following in 7th paragraph.
- for thin materials, e.g., flexible printed boards, etc.,
used inside equipment, be of FLAMMABILITY CLASS
VTM-2 or better.
used inside equipment, be of FLAMMABILITY CLASS
VTM-2 or better.
Considered. N/A
Click on the first or last page to see other ON STAGEII (serv.man12) service manuals if exist.