DOWNLOAD JBL ON BEAT MINI Service Manual ↓ Size: 1.92 MB | Pages: 71 in PDF or view online for FREE

 

 

Page 12 of 16 

Report No.: W13-950-006  

IEC60950_1B - ATTACHMENT 

Clause 

Requirement + Test 

Result - Remark 

Verdict

 

2.7.1 In 

the 

, to protect against 

excessive currents and short-circuits in the 
PRIMARY CIRCUIT of DIRECT PLUG-IN 
EQUIPMENT, tests according to 5.3 shall be 
conducted, using an external protective device 
rated 30 A or 32 A. If these tests fail, suitable 
protective devices shall be included as integral 
parts of the DIRECT PLUG-IN EQUIPMENT, so 
that the requirements of 5.3 are met. 

 N/A 

2.10.5.13 In 

, Norway and Sweden, there are 

additional requirements for the insulation, see 
6.1.2.1 and 6.1.2.2 of this annex. 

 N/A 

3.2.1.1 

In Switzerland, supply cords of equipment 
having a RATED CURRENT not exceeding 10 A 
shall be provided with a plug complying with SEV 
1011 or IEC 60884-1 and one of the following 
dimension sheets: 
SEV 6532-2.1991   Plug Type 15 
 

3P+N+PE   250/400 V, 10 A  

 N/A 

 

SEV 6533-2.1991   Plug Type 11  

L+N  

 

250 V, 10 A                                                   

SEV 6534-2.1991   Plug Type 12  

L+N+PE 

 

250 V, 10 A 

In general, EN 60309 applies for plugs for 
currents exceeding 10 A. However, a 16 A plug 
and socket-outlet system is being introduced in 
Switzerland, the plugs of which are according to 
the following dimension sheets, published in 
February 1998: 
SEV 5932-2.1998: Plug Type 25 , 3L+N+PE 
230/400 V, 16 A 
 
SEV 5933-2.1998:Plug Type 21, L+N, 250 V, 16A
 
SEV 5934-2.1998: Plug Type 23, L+N+PE 250 V, 1

 N/A 

 

 

Page 13 of 16 

Report No.: W13-950-006  

IEC60950_1B - ATTACHMENT 

Clause 

Requirement + Test 

Result - Remark 

Verdict

 

3.2.1.1 

In Denmark, supply cords of single-phase 
equipment having a rated current not 
exceeding13 A shall be provided with a plug 
according to the Heavy Current Regulations, 
Section 107-2-D1. 
CLASS I EQUIPMENT provided with socket-
outlets with earth contacts or which are intended 
to be used in locations where protection against 
indirect contact is required according to the wiring 
rules shall be provided with a plug in accordance 
with standard sheet DK 2-1a or DK 2-5a. 
If poly-phase equipment and single-phase 
equipment having a RATED CURRENT 
exceeding 13 A is provided with a supply cord 
with a plug, this plug shall be in accordance with 
the Heavy Current Regulations, Section 107-2-D1 
or EN 60309-2. 

 N/A 

3.2.1.1 

In Spain, supply cords of single-phase equipment 
having a rated current not exceeding 10 A shall 
be provided with a plug according to UNE 
20315:1994. 
Supply cords of single-phase equipment having a 
rated current not exceeding 2,5 A shall be 
provided with a plug according to UNE-EN 
50075:1993. 
CLASS I EQUIPMENT provided with socket-
outlets with earth contacts or which are intended 
to be used in locations where protection against 
indirect contact is required according to the wiring 
rules, shall be provided with a plug in accordance 
with standard UNE 20315:1994. 
If poly-phase equipment is provided with a supply 
cord with a plug, this plug shall be in accordance 
with UNE-EN 60309-2. 

 N/A 

3.2.1.1 

In the United Kingdom, apparatus which is fitted 
with a flexible cable or cord and is designed to be 
connected to a mains socket conforming to BS 
1363 by means of that flexible cable or cord and 
plug, shall be fitted with a ‘standard plug’ in 
accordance with Statutory Instrument 1768:1994 
- The Plugs and Sockets etc. (Safety) 
Regulations 1994, unless exempted by those 
regulations. 

NOTE ‘Standard plug’ is defined in SI 1768:1994 and 
essentially means an approved plug conforming to BS 
1363 or an approved conversion plug.

 

 N/A 

 

 

Page 14 of 16 

Report No.: W13-950-006  

IEC60950_1B - ATTACHMENT 

Clause 

Requirement + Test 

Result - Remark 

Verdict

 

3.2.1.1 

In Ireland, apparatus which is fitted with a flexible 
cable or cord and is designed to be connected to 
a mains socket conforming to I.S. 411 by means 
of that flexible cable or cord and plug, shall be 
fitted with a 13 A plug in accordance with 
Statutory Instrument 525:1997 - National 
Standards Authority of Ireland (section 28) (13 A 
Plugs and Conversion Adaptors for Domestic 
Use) Regulations 1997. 

 N/A 

3.2.4 

In Switzerland, for requirements see 3.2.1.1 of 
this annex. 

 N/A 

3.2.5.1 

In the United Kingdom, a power supply cord with 
conductor of 1,25 mm2 is allowed for equipment 
with a rated current over 10 A and up to and 
including 13 A. 

 N/A 

3.3.4 

In the United Kingdom, the range of conductor 
sizes of flexible cords to be accepted by terminals 
for equipment with a RATED CURRENT of over 
10 A up to and including 13 A is: 
• 1,25 mm

2

 to 1,5 mm

2

 nominal cross-sectional 

area. 

 N/A 

4.3.6 

In the United Kingdom, the torque test is 
performed using a socket outlet complying with 
BS 1363 part 1:1995, including Amendment 
1:1997 and Amendment 2:2003 and the plug part 
of DIRECT PLUG-IN EQUIPMENT shall be 
assessed to BS 1363: Part 1, 12.1, 12.2, 12.3, 
12.9, 12.11, 12.12, 12.13, 12.16 and 12.17, 
except that the test of 12.17 is performed at not 
less than 125 °C. Where the metal earth pin is 
replaced by an Insulated Shutter Opening Device 
(ISOD), the requirements of clauses 22.2 and 23 
also apply. 

 N/A 

4.3.6 

In Ireland, DIRECT PLUG-IN EQUIPMENT is 
known as plug similar devices. Such devices shall 
comply with Statutory Instrument 526:1997 - 
National Standards Authority of Ireland (Section 
28) (Electrical plugs, plug similar devices and 
sockets for domestic use) Regulations, 1997. 

 N/A 

 

 

Page 15 of 16 

Report No.: W13-950-006  

IEC60950_1B - ATTACHMENT 

Clause 

Requirement + Test 

Result - Remark 

Verdict

 

5.1.7.1 

In Finland, Norway and Sweden TOUCH 
CURRENT measurement results exceeding 3,5 
mA r.m.s. are permitted only for the following 
equipment: 
• STATIONARY PLUGGABLE EQUIPMENT 
TYPE A that  
 

is intended to be used in a RESTRICTED 

ACCESS LOCATION where equipotential 
bonding has been applied, for example, in a  
telecommunication centre; and 
 

has provision for a permanently connected 

PROTECTIVE EARTHING CONDUCTOR; and 
 

is provided with instructions for the 

installation of that conductor by a SERVICE 
PERSON; 
• STATIONARY PLUGGABLE EQUIPMENT 
TYPE B; 
• STATIONARY PERMANENTLY CONNECTED 
EQUIPMENT. 

 N/A 

6.1.2.1 

(A1:2010)

 

In Finland, Norway and Sweden, add the 
following text between the first and second 
paragraph of the compliance clause: 
If this insulation is solid, including insulation 
forming part of a component, it shall at least 
consist of either 
- 

two layers of thin sheet material, each of 

which shall pass the electric strength test below, 
or 
- 

one layer having a distance through 

insulation of at least 0,4 mm, which shall pass the 
electric strength test below. 
Alternatively for components, there is no distance 
through insulation requirements for the insulation 
consisting of an insulating compound completely 
filling the casing, so that CLEARANCES and 
CREEPAGE DISTANCES do not exist, if the 
component passes the electric strength test in 
accordance with the compliance clause below 
and in addition 
- 

passes the tests and inspection criteria of 

2.10.11 with an electric strength test of 1,5 kV 
multiplied by 1,6 (the electric strength test of    
2.10.10 shall be performed using 1,5 kV), and 
- 

is subject to ROUTINE TESTING for 

electric strength during manufacturing, using a 
test voltage of 1,5 kV. 

 N/A