JBL JSR 655 User Manual / Operation Manual ▷ View online
8
1. FM INDOOR ANTENNA
Connect the supplied antenna (the
wire lead) to a 300
wire lead) to a 300
Ω
/75
Ω
adapter
and connect the adapter to the 75
Ω
T-shaped FM antenna terminal, as
shown in the Rear Panel Connection
Diagram. Change the position of the
antenna until you get the best recep-
tion of your favorite stations.
shown in the Rear Panel Connection
Diagram. Change the position of the
antenna until you get the best recep-
tion of your favorite stations.
2. FM OUTDOOR
ANTENNA
ANTENNA
An outdoor FM antenna may be used
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
Ω
/300
Ω
adapter
must be used.
3. AM LOOP ANTENNA
Tune in your favorite AM station and
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
NOTE:
If noise is heard during AM
reception, move the antenna for bet-
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 30 cm
away from the remote control wiring.
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 30 cm
away from the remote control wiring.
4. SYSTEM GROUND
TERMINAL
TERMINAL
To reduce hum to a minimum, con-
nect the ground lead from your
turntable to this terminal.
nect the ground lead from your
turntable to this terminal.
5. PHONO INPUT JACKS
Input for TURNTABLE with an MM
cartridge having 47K ohms of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
cartridge having 47K ohms of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
NOTE:
Do not place your
TURNTABLE on a speaker enclosure.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
6. TV/AUX INPUT JACKS
This extra stereo input is provided for
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
7. CD INPUT JACKS
Connect the output cables of a com-
pact disc player to these jacks.
pact disc player to these jacks.
8. TAPE 1 PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
9. TAPE 1 REC JACKS
Connect the line input of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
10. TAPE 2 MONITOR
PLAY JACKS
PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
11. TAPE 2 MONITOR REC
JACKS
JACKS
Connect the line input of your
CASSETTE DECK to these jacks. EQ
controls, loudness and volume set-
tings have no effect on the signal
from this output for recording. To
monitor this input source while
recording, press the TAPE 2 MONI-
TOR button (MONITOR ON position).
These REC jacks may be used for the
line input of the audio processor like
an optional graphic equalizer or a
Digital Signal Processor.
CASSETTE DECK to these jacks. EQ
controls, loudness and volume set-
tings have no effect on the signal
from this output for recording. To
monitor this input source while
recording, press the TAPE 2 MONI-
TOR button (MONITOR ON position).
These REC jacks may be used for the
line input of the audio processor like
an optional graphic equalizer or a
Digital Signal Processor.
AM LOOP ANTENNA SETTING
Stand and place it on a shelf
or hang it on a wall.
or hang it on a wall.
LEG
Rear Panel Connections
JSR655om (a) qx 7/28/98 9:54 AM Page 10
9
12. VIDEO/AUDIO INPUT
(PLAY) JACKS OF VCR 1
(PLAY) JACKS OF VCR 1
Connect these jacks to the corre-
sponding AUDIO OUTPUT jacks of
your VCR.
sponding AUDIO OUTPUT jacks of
your VCR.
13. VIDEO/AUDIO OUTPUT
(REC) JACKS OF VCR 1
(REC) JACKS OF VCR 1
Connect these jacks to the corre-
sponding INPUT jacks of a VCR.
VIDEO OUTPUT jack: Connect this
jack to the VIDEO INPUT jack of the
VCR. AUDIO REC jack: Connect
these jacks to the AUDIO INPUT
jacks of the VCR.
sponding INPUT jacks of a VCR.
VIDEO OUTPUT jack: Connect this
jack to the VIDEO INPUT jack of the
VCR. AUDIO REC jack: Connect
these jacks to the AUDIO INPUT
jacks of the VCR.
14. VIDEO/AUDIO INPUT
(PLAY) JACKS OF VCR 2
(PLAY) JACKS OF VCR 2
Connect these jacks to the corre-
sponding OUTPUT jacks of your VCR
or VDP.
sponding OUTPUT jacks of your VCR
or VDP.
15. VIDEO MONITOR JACK
Connect this jack to the VIDEO
INPUT jack of a TV/MONITOR.
INPUT jack of a TV/MONITOR.
16. REMOTE CONTROL
OUT JACK
OUT JACK
Connect this jack to the “REMOTE IN”
jack on a Harman Kardon component.
Use one of the accessory mini-plug
cables.
jack on a Harman Kardon component.
Use one of the accessory mini-plug
cables.
You can control some Harman Kardon
components in your system using the
JSR655 remote commander.
components in your system using the
JSR655 remote commander.
17. MULTI-ROOM REMOTE
IN JACK
IN JACK
Connect a remote IR sensor to this
jack. You can operate the unit by
remote commander through the
adapter. It is convenient when the unit
is located in a separate room. (See
page 10)
jack. You can operate the unit by
remote commander through the
adapter. It is convenient when the unit
is located in a separate room. (See
page 10)
18. FRONT, CENTER,
REAR PRE OUT AND MAIN
IN JACKS
REAR PRE OUT AND MAIN
IN JACKS
FRONT PRE OUT
When a separate power amplifier is
used to drive the front speakers, con-
nect the power amplifier input to
these jacks.
used to drive the front speakers, con-
nect the power amplifier input to
these jacks.
FRONT MAIN IN
When a separate pre-amplifier is con-
nected and this unit is used as a
power amplifier, connect the pre-
amplifier output to these jacks.
nected and this unit is used as a
power amplifier, connect the pre-
amplifier output to these jacks.
NOTE:
When you do not use the
PRE OUT and MAIN IN separately,
always connect the PRE OUT and
MAIN IN jacks with a jumper plug.
always connect the PRE OUT and
MAIN IN jacks with a jumper plug.
CENTER PRE OUT
When a separate power amplifier is
used to drive the center speaker,
connect the power amplifier input to
these jacks.
used to drive the center speaker,
connect the power amplifier input to
these jacks.
REAR PRE OUT
When a separate power amplifier is
used to drive the rear speaker, con-
nect the power amplifier input to
these jacks.
used to drive the rear speaker, con-
nect the power amplifier input to
these jacks.
19. 1/ 2 SPEAKER
TERMINALS
TERMINALS
Connect the main left (L) and right
(R) speakers to the corresponding A
and B speaker terminals. Make sure
that the positive (+) and negative (-)
terminals on the speaker are con-
nected to the corresponding termi-
nals on the receiver.
(R) speakers to the corresponding A
and B speaker terminals. Make sure
that the positive (+) and negative (-)
terminals on the speaker are con-
nected to the corresponding termi-
nals on the receiver.
19A. CENTER SPEAKER
TERMINALS
TERMINALS
Connect the corresponding positive
and negative terminals on the center
speaker to the positive (+) and nega-
tive (-) terminals on the receiver.
and negative terminals on the center
speaker to the positive (+) and nega-
tive (-) terminals on the receiver.
20. REAR SPEAKER
TERMINALS
TERMINALS
Connect rear speakers to the corre-
sponding terminals. When you con-
nect the rear speakers, connect both
L and R speakers.
sponding terminals. When you con-
nect the rear speakers, connect both
L and R speakers.
21. AC INPUT CORD
Plug this cord in the AC outlet on
a wall.
a wall.
22. SUBWOOFER OUT
When a separate power amplifier is
used to drive a subwoofer, connect
the power amplifier inputs to these
jacks.
used to drive a subwoofer, connect
the power amplifier inputs to these
jacks.
JSR655om (a) qx 7/28/98 9:54 AM Page 11
10
REAR SPEAKERS
RIGHT
8
Ω
LEFT
8
Ω
REMOTE CONTROL
REMOTE
REMOTE IR SENSOR
REMOTE ROOM
MAIN ROOM
REMOTE
COMMANDER
COMMANDER
2 SPKR
LEFT
LEFT
1 SPKR
LEFT
LEFT
1 SPKR
RIGHT
RIGHT
2 SPKR
RIGHT
RIGHT
REMOTE IR SENSOR
RECEIVER
Volume
Speakers
1
2
FM Mode
Search
AM
FM
Tuning
Loudness
1
2
3
4
5
P. Scan
0-30
Memory
6
7
8
9
0
Surround
Input
VCR2
VCR1
VCR2
Delay
Surround
Center
Test
Tape 2 Mon
Tape 1
VCR2
VCR1
TV/Aux
Tuner
Phono
CD
Power
Headphones
SetRec
Set
Bass
Treble
Balance
DOLBY SURROUND
P R O • L O G I C
P R O • L O G I C
JSR655 DOLBY® SURROUND RECEIVER
PRO-LOGIC
DOLBY SURROUND
MHz
FM
AM
MONO
SEARCH
TAPE MONITOR
PRESET
MEMORY
MS
MIN
DELAY
TIME
SLEEP
TIME
SLEEP
CENTER MODE
PHANTOM
NORM
WIDE
VCR 1 DUBBING
KHz
3 STEREO
HALL
CD
Tape1
Tape2
TV/Aux
VCR1
VCR2
CassDeck
Skip
Intro
Search
Phono
Tuner
A-B
A/B
Select
Delay
Off
Hall
Surround
3-Stereo
Pro-Logic
Display
Sleep
Mute
RearLevel
MasterVolume
CenterLevel
CentMode
Test
Power
Tuning
PScan
T
uner
CD
1
2
3
4
5
6
7
8
9
0
Disc
IN
OUT
Optional Multi-Room Control
Adapter Connection
Adapter Connection
JSR655om (a) qx 7/28/98 9:54 AM Page 12
11
LINE-IN
PRE OUT
PRE OUT PRE OUT
MAIN IN
LEFT
RIGHT
FRONT
CENTER
REAR
L
R
CENTER
SPEAKER
(Remove PRE OUT/MAIN IN jumpers when the front speakers are connected to external amplifier.)
FRONT(left)
FRONT(right)
Power
LEFT
RIGHT
RIGHT
USE 8 OHM MIN SPEAKERS
FRONT SPEAKERS
-1
-2
Power Amplifier
CENTER
SPEAKERS
SUBWOOFER
OUT
8
Ω
LEFT
RIGHT
LEFT
REAR SPEAKERS
RIGHT
8
Ω
LEFT
8
Ω
When you drive the front speakers with another amplifier
JSR655om (a) qx 7/28/98 9:54 AM Page 13
Click on the first or last page to see other JSR 655 service manuals if exist.