Harman Kardon ONYX STUDIO Service Manual ▷ View online
Harman Kardon Onyx Studio
Assembly procedure
Soldering and fixing Tweeter Cable-long and
Tweeter Cable-short by sequence.
Tweeter Cable-short by sequence.
Note: Do not over 5s for the soldering, and
make sure the soldering quality and tightness.
make sure the soldering quality and tightness.
9. 取 Speaker Cable 按正負極連接到 Mid
Woofer 對應位置
Connect the Speaker Cable to the Mid Woofer.
Woofer 對應位置
Connect the Speaker Cable to the Mid Woofer.
注意：紅“+”黑“-”，紅色 Cable 線對應 Mid
Woofer "+"極，黑色 Cable 線對應 Mid Woofer
"-"極；Woofer Cable-long 和 Woofer Cable-short
不可接反
Woofer "+"極，黑色 Cable 線對應 Mid Woofer
"-"極；Woofer Cable-long 和 Woofer Cable-short
不可接反
Note: Red “+” Cable with Mid Woofer "+"
Black”-“ with Mid Woofer "-" , please make sure
the direction of Woofer Cable-long and Woofer
Cable-short.
Black”-“ with Mid Woofer "-" , please make sure
the direction of Woofer Cable-long and Woofer
Cable-short.
10. 將主板對準面框螺柱，注意藍牙天線走主
板下側經過，不能接觸鼓膜
板下側經過，不能接觸鼓膜
注意：主板定位孔需對到位
Note: Position the MB hole shown as the figure.
Note: Position the MB hole shown as the figure.
黑色在上,“-”極
紅色在下,
“+”極
紅色在上,
“+”極
黑色在下,“-”極
Woofer Cable-long
Woofer Cable-short
藍牙天線理在螺柱內
側，不能接觸鼓膜
排線走螺柱
內側
排線走螺柱內側
Harman Kardon Onyx Studio
Assembly procedure
Assemble the MB to the post and let the BT A
Antenna under the MB, and do not touch Mid
woofer.
Antenna under the MB, and do not touch Mid
woofer.
11.使用螺絲起子，依次鎖付 4PCs 螺絲
(3*8.2MM)固定主板
Tightens 4 screws by using the T10 screwdriver.
(3*8.2MM)固定主板
Tightens 4 screws by using the T10 screwdriver.
注意：主板定位孔需對到位
Note: Position the MB hole shown as the figure.
12. 將 Speak Cable 連接到主板指定接口；將
天線連接到主板對應位置，注意扣合到位
Assemble the Speak Cable and BT Antenna to
天線連接到主板對應位置，注意扣合到位
Assemble the Speak Cable and BT Antenna to
12.1 將喇叭排線理到喇叭側下邊經過，不能在
螺絲上方經過
Arrange the Speak Cable under the Speaker and
螺絲上方經過
Arrange the Speak Cable under the Speaker and
定位孔
2
3
4
1
藍牙天線
Speak
Cable
Speaker Cable 理在
側下邊經過
Harman Kardon Onyx Studio
Assembly procedure
the MB shown in the figure.
it shouldn’t pass by the upper screw.
13. 取 4PCs 泡棉粘貼到按鍵板指定位置
Assemble 4 sponges to the switches shown in
the figure.
Assemble 4 sponges to the switches shown in
the figure.
注意：
泡棉粘貼在白線中間位置，兩側靠末端
粘貼，長於部份朝缺口側粘貼
Note: If the length is longer, please stick near
the gap.
the gap.
14. 將按鍵板從排線接口位置開始組裝，再依
次左右兩側卡入面框
Assemble the Cable first and then assemble the
both sides of the keys.
次左右兩側卡入面框
Assemble the Cable first and then assemble the
both sides of the keys.
注意：
按鍵板需注意組裝方法，防止折斷按鍵
板
Note: Do not bend the key PCB.
多餘部份朝缺口
側粘貼
藍牙鍵
“-”鍵
“+”鍵
注意：按鍵板先裝
接口位置
Harman Kardon Onyx Studio
Assembly procedure
15. 取 Rubber Ring 對準按鍵處依次往面框側
組裝
Assemble the rubber ring and align the keys by
sequence.
組裝
Assemble the rubber ring and align the keys by
sequence.
注意：
Rubber Ring 需注意組裝方法，需卡到
位
Note: Take care the assembly method and its
position.
position.
16. 把 Back Radiator 組裝到後殼對應位置
(Front Radiator 安裝位置有防呆設計)；取螺絲
起子，依次鎖付 4PCs 螺絲(3*10.2MM)
(Front Radiator 安裝位置有防呆設計)；取螺絲
起子，依次鎖付 4PCs 螺絲(3*10.2MM)
Assemble the Back Radiator to the back of back
cover shown in the figure. Tightens 4 screws by
using the T10 screwdriver.
cover shown in the figure. Tightens 4 screws by
using the T10 screwdriver.
Rubber Ring
“-”鍵
“+”鍵
Power 鍵
藍牙鍵
Back Raditor 以
凸起定位
2
3
4
1
Click on the first or last page to see other ONYX STUDIO service manuals if exist.